Creating a Surfacic Flange

This section explains how to create a surfacic flange on a web, or an existing surfacic flange.

Understanding the surfacic flange

When creating a surfacic flange, the bend is propagated along the whole base feature (with a continuity in tangency).

In certain cases this propagation prevents the surfacic flange from being relimited: this happens when the selected edge allows propagation of the bend.

   

Open the SurfacicFlange1.CATPart document.

Here are the different elements taken into account when creating a surfacic flange:
  1. Click Surfacic Flange .

    The Surfacic Flange definition dialog box is displayed.
     
     

    Base Feature

     
    In the Base Feature tab, the Bend Radius is of Constant type. It is set to the default bend radius of the part.
  2. You can modify the fillet Radius value by changing the driving equation. To do so, click .
    The Formula Editor dialog box opens and you can then modify the dictionary and the parameters.

    Or you may need to deactivate the formula using the contextual menu on the field and choosing Formula -> Deactivate before editing the value.
  3. Choose the web as the Base Feature.

    Once you chose the base feature, the Support tab automatically displays. 
     

    Support

     
     
  4. In the Support tab, choose the surfacic flange's geometrical support. It can either be a surface, a plane or a curve.

    A preview of the surfacic flange is displayed.
     
     
    • In case the preview of the surfacic flange is not displayed, you should not be able to create it.
    • Remember that the preview helps you build the surfacic flange but that the computation is only partial. For instance, it does not include relimitations of a surfacic flange.
       
    Make sure the support is big enough to be able to later define an EOP with a length from OML.
       
    Three types of support are available:
    • Exact: the selected support is to be used for the creation of the surfacic flange.
    • Approximation:  the support surface is approximated using a ruled surface. This ruled surface is defined from two curves:
      • the OML (in light blue), computed at the intersection between the support surface and the web plane.
      • a curve parallel to the OML (in pink), computed at a distance equal  to the approximation length

      This mode enables you to compute the maximum deviation between the support geometry and the approximated surface.

       
    • Angle: the support of the surfacic flange can also be defined by a line, a curve, an angle or the edge of a base feature. The angle is constant and you can change its value using the spinners.

     
    You cannot build a surfacic flange if you select only a part of the support's edge since relimitations are not computed.

    For instance, in the example below, the surfacic flange cannot be build, since it is not possible to select the whole edge of the web.

       
    Instead, you have to select a sketch (displayed in red) or a curve (displayed in blue) to be able to build a surfacic flange.
     
     
    You can modify the Support Length generated by the curve and the angle. By default, the length is set to ten times the EOP (Edge of Part) length. If the default EOP length is higher than 100mm, you need to modify the surface length.
     
    The red angle is the angle taken into account when creating the surfacic flange.
  5. Define the vectors' directions.

    You can modify the directions by clicking the arrows in the geometry or you can use the buttons available in the Surfacic Flange Definition dialog box.
    • The Material's vector shows on which side of the support surface the surfacic flange will be built;
    • The Base Feature's vector shows the part that will be kept according to the support surface;
    • The Surfacic Flange's vector shows the direction in which the surfacic flange will be built.
     
     
     
    The surfaces (or curves) used to define the support surface must be continuous in point and tangency.
       

    EOP

     
  6. In the EOP (Edge Of Part) tab, you can define either:

    • a length from OML (Outer Mold Line): length between the curve defining the top of the surfacic flange and the OML,

    • an element FD (Folded): boundary element (either a surface that intersects with its surface, or a sketch, or a wire projected on its surface),

    • an element FP (Flat Pattern): curve or sketch defining the flattened profile of the surfacic flange. 

     
    The element FP must be included within the limits of the surfacic flange support when folded.
     
  7. Click OK.

    The Surfacic Flange (identified as Surfacic Flange.xxx) is created and the specification tree is updated accordingly.
     
    Surfacic Flange with a length from OML of 15 mm
     
    Surfacic Flange with Plane.2 (in pink) as Element FD
     
    Surfacic Flange with EOP FP (in light blue) as Element FP
     
    Unfolded view of the Surfacic Flange with EOP FP as Element FP.
     
    See Unfolding.

Sides and Corners

In the Sides and Corners tab, you can choose to define the following elements:

  • sides (intersection between the Base Feature and a curve) as:
    • standard: they are automatically defined at the web limit and the perpendicular plans are kept (in this case, the user does not have to define them)
    • none: no side computed (only the EOP will define the profile of the Flange)
    • element FD (Folded): they are defined by a folded  geometrical element (curve, plane or surface). 
    • element FP (Flat Pattern): curve defining the flattened profile of the flange.

 

   
 
Surfacic Flange defined with a Length from OML of 10mm, and Side 1 and 2 as Standard
 
 
Surfacic Flange defined with EOP FD as Element FD, and Side 1 and 2 as None
 
 
Folded view of the Surfacic Flange with EOP FP as Element FP, Side 1 FP and Side 2 FP (in light brown) as Side 1 and Side 2.
See Unfolding.
 
 
Unfolded view of the Surfacic Flange with EOP FP as Element FP, Side 1 FP and Side 2 FP (in light brown) as Side 1 and Side 2.
See Unfolding.
 
  1. The following examples show two cases of a flange defined by an EOP FP or FD and Sides as None.

There is an intersection between the EOP and the web support -> the Surfacic Flange can be computed

There is no intersection between the EOP and the web support -> the Surfacic Flange cannot be computed

  1. The following examples show two cases of a flange defined by an element FD as the EOP and Standard sides.

There is an intersection between the EOP and the side -> the Surfacic Flange can be computed

There is no intersection between the EOP and the side  -> the Surfacic Flange cannot be computed

  1. The following examples show two cases of a flange defined by an element FP as the EOP and Standard sides.

There is an intersection between the OML and the EOP -> the Surfacic Flange can be computed

There is no intersection between the OML and the EOP -> the Surfacic Flange cannot be computed

  1. The following examples show three cases of a flange defined by an element FD as the side.
  There is an intersection between the Element FD and the OML and between the side and the EOP -> the Surfacic Flange can be computed
  There is an intersection between the side and the OML but no intersection between the side and the EOP -> the Surfacic Flange cannot be computed
  There is an intersection between the side and the EOP but no intersection between the side and the OML -> the Surfacic Flange cannot be computed
  1. The following examples show three cases of a flange defined by an element FD as the side.
  There is an intersection between the side and the EOP and between the side and the OML -> the Surfacic Flange can be computed
  There is an intersection between the side and the OML but no intersection between the side and the EOP -> the Surfacic Flange cannot be computed
  There is an intersection between the side and the EOP but no intersection between the side and the OML -> the Surfacic Flange cannot be computed
 
Any cutout on the web will be taken into account to create the surfacic flange's sides. For example, if you create a cutout on the web, then create a surfacic flange with standard sides, the latter will be calculated from the web's profile including the cutout.
For optimization reasons, we advise you to first create a sketch with the desired shape, then create the surfacic flange.
 
  A surfacic flange with a side limit defined by a plane or a curve cannot be created in the case when the side projection (displayed in blue on the second picture) of the top of the flange overtakes the supporting surface.
   
  In such a case, you have to make sure the supporting surface is large enough before creating the flange. In the picture below, the supporting surface has been extrapolated.
 
   

The example above shows a Surfacic Flange with standard sides calculated from the web modified by a cutout (the cutout, shown in blue, is taken into account)

  You can create several surfacic flanges on a web already containing cutouts by selecting the web and the same support plane.

  In such a case, each surfacic flange can be opened and modified independently from the others. Yet, if the support of one of the surfacic flanges was to be modified, the change would be propagated to the other surfacic flanges.
  • corners (profile defined between the EOP and the sides) as:
    • none: no corner computed (only the EOP is able to define the profile of the Surfacic Flange)
    • corner: between the side and the EOP (defined with a radius value)

The example above shows a Surfacic Flange defined with Sides 1 and 2 as Standard, and Corners 1 and 2 of 10mm each.

 

 
  • In the case the user does not define a surfacic flange side, the latter is automatically computed at the Web limit, perpendicular to the OML.
  • In the case no corner is defined, the side and the EOP are simply relimiting each other.
  • The sides of the fillet are continuous in tangency with the profile of the web and the sides of the surfacic flange.
   
 

Process

 
  In the Process tab, you can define the:
  • Manufacturing process:
    • Hydropressed
    • BreakFormed
  • K_Factor: you can modify the K Factor as defined in the SheetMetal Parameters dialog box by changing the driving equation.
    Click the icon. The Formula Editor dialog box opens, you can modify the dictionary and the parameters. Or you may need to deactivate the formula using the contextual menu on the field and choosing Formula -> Deactivate before editing the value.

 

Prior to R16, in the Process tab, you could also use the Show curves in folded views and Show curves in flattened  view check boxes to display the characteristic curves of a given surfacic flange on the folded view and/or on the unfolded view of the part. The display of characteristic curves is now managed through settings, and for an entire part. For more information, refer to Display in the Customizing chapter.
 

Compensations

 
In the Compensations tab, you can define compensations for the:
  • Joggle:
    • check the Apply Compensation button when creating or editing the joggle.
      See Creating a Joggle for further information.

Standard files and methods must be previously defined from the SheetMetal Parameters dialog box to have access to the Apply Compensation button.

  • Surfacic Flange Sides (Side 1 and Side 2).
    • Define the type:
      • None: no compensation is applied

      • Automatic: for symmetric flanges , A1=A2, so that the length of the flatten EOP = length of the folded EOP

      • Manual: Angle: the deformation is computed according to an angle

      • Manual: Length: the deformation is computed according to a length parallel to the BTL.

    • Define the Angle in the case of a Manual: Angle compensation. A negative angle adds material, and a positive angle removes material.

    • Define the Length in the case of a Manual: Length compensation

 

 
The values of the modification are the angles A1 and A2.
 
 
  • Compensations can be created either on the folded or flattened part, but they only apply on the flattened part.
  • Compensations can be modified independently on each flange.
  • The + sign (in yellow in the 3D geometry) shows that material will be added to the sides.
 

 

Unfolded Surfacic Flange defined with Corners 1 and 2 of 10mm each, and no compensation for Side 1 and Side 2  

Unfolded Surfacic Flange defined with Corners 1 and 2 of 10mm each, a Manual: Angle compensation of -20deg for Side 1 and no compensation for Side 2

Unfolded Surfacic Flange defined with Corners 1 and 2 of 10mm each, a Manual: Angle compensation of 20deg for Side 1 and -10deg for Side 2

More about surfacic flanges

Hybrid Design

  • In hybrid design context, when the edge of a part and/or the surfacic flange are defined by a sketch, they follow the hybrid design aggregation rules.
  • Yet, if you open a part created using an application release prior to Version 5 Release 14, the specification tree is displayed according to the rules implemented for that release.

For more information about Hybrid Design, refer to the Hybrid Design section in the Part Design User's Guide.

Creating Adjacent Flanges

Creating two adjacent flanges may be impossible for some specific flange topologies (the unfolded view cannot be computed properly). In this case, a specific warning message is displayed, advising you to create a notch on the web before trying to create the second surfacic flange.

 

Intersecting surfacic flanges on a web

It is now possible to intersect two surfacic flanges on a web. This means that you can choose as a support a web with an existing surfacic flange that will go through the new surfacic flange.

The intersecting flanges are automatically detected, and the geometry of the first flange is relimited to enable the creation of the second flange; the unfolded view is computed accordingly. You can then remove the sharp vertex in the corner by creating a corner relief or a cutout at the intersection of the surfacic flanges.

 
  Different topological cases may be encountered. In all cases, the common ribbon is removed and the current surfacic flange is cut in a natural way. A few examples are shown below.
  Intersecting surfacic flanges with same bend radii and angles (general case)
   
  Intersecting surfacic flanges with different bend radii
   
  Intersecting surfacic flanges with different bend radii and angles
 
  • The characteristic curves of the previous adjacent flanges (split by the current one) are not split.
  • The capability works only between two surfacic flanges.
  • The adjacent flanges may include joggles, provided that the surfacic flange is not trimmed through a joggle runout.
   

Joggled surfacic flange

You cannot build a Surfacic Flange on a joggled Surfacic Flange.