The optimal settings of the tunable communications parameters vary with the type of LAN, as well as with the communications-I/O characteristics of the predominant system and application programs. The following sections describe the global principles of communications tuning, followed by specific recommendations for the different types of LAN.
You can choose to tune primarily either for maximum throughput or for minimum memory use. Some recommendations apply to one or the other; some apply to both. Recommended application block sizes for different adapter devices are as follows:
| Device Name | Application Block Size |
| Ethernet | Multiples of 4096 |
| Token-Ring (4 Mb) | Multiples of 4096 |
| Token-Ring (16 Mb) | Multiples of 4096 |
| FDDI (tcp) | Multiples of 4096 |
| SOCC (tcp) | 28672 bytes |
| HIPPI | 65536 bytes |
| ATM | Multiples of 4096 |
Use the following recommendations to tune for maximum throughput:
Follow these guidelines:
(a multiple of the MTU size minus 28 bytes to allow for standard IP and UDP headers).
Follow these guidelines:
Use the following recommendations to tune for minimizing memory usage:
OR
If the applications were using TCP, both time and memory would be wasted. TCP tries to form outbound data into MTU-sized packets. If the MTU of the LAN were larger than 14976 bytes, TCP would put the sending thread to sleep when the tcp_sendspace limit was reached.To force the data to be written, a timeout ACK from the receiver would be required.
Most communication drivers provide a set of tunable parameters to control transmit and receive resources. These parameters typically control the transmit queue and receive queue limits, but may also control the number and size of buffers or other resources. These parameters limit the number of buffers or packets that may be queued for transmit or limit the number of receive buffers that are available for receiving packets. These parameters can be tuned to ensure enough queueing at the adapter level to handle the peak loads generated by the system or the network.
Following are some general guidelines:
For transmit, the device drivers may provide a transmit queue limit. There may be both hardware queue and software queue limits, depending on the driver and adapter. Some drivers have only a hardware queue; some have both hardware and software queues. Some drivers internally control the hardware queue and only allow the software queue limits to be modified. Generally, the device driver will queue a transmit packet directly to the adapter hardware queue. If the system CPU is fast relative to the speed of the network, or on an SMP system, the system may produce transmit packets faster than they can be transmitted on the network. This will cause the hardware queue to fill. After the hardware queue is full, some drivers provide a software queue and they will then queue to the software queue. If the software transmit queue limit is reached, then the transmit packets are discarded. This can affect performance because the upper-level protocols must then time out and retransmit the packet.
Prior to AIX 4.2.1, the upper limits on the transmit queues were in the range of 150 to 250, depending on the specific adapter. The system default values were low, typically 30. With AIX 4.2.1 and later, the transmit queue limits were increased on most of the device drivers to 2048 buffers. The default values were also increased to 512 for most of these drivers. The default values were increased because the faster CPUs and SMP systems can overrun the smaller queue limits.
Following are examples of MCA adapter transmit queue sizes:
| MCA Adapter Type | Default | Range |
| Ethernet | 512 | 20 - 2048 |
| 10/100 Ethernet | 64 | 16,32,64,128,256 |
| Token-Ring | 99 or 512 | 32 - 2048 |
| FDDI | 512 | 3 - 2048 |
| ATM / 155 ATM | 512 | 0 - 2048 |
Following are examples of PCI adapter transmit queue sizes:
| PCI Adapter Type | Default | Range |
| Ethernet | 64 | 16 - 256 |
| 10/100 Ethernet | 256, 512, or 2048 | 16 -16384 |
| Token-Ring | 96, 512, or 2048 | 32 - 16384 |
| FDDI | 30 or 2048 | 3 - 16384 |
| 155 ATM | 100 or 2048 | 0 - 16384 |
For adapters that provide hardware queue limits, changing these values will cause more real memory to be consumed on receives because of the associated control blocks and buffers associated with them. Therefore, raise these limits only if needed or for larger systems where the increase in memory use is negligible. For the software transmit queue limits, increasing these limits does not increase memory usage. It only allows packets to be queued that were already allocated by the higher layer protocols.
Some adapters allow you to configure the number of resources used for receiving packets from the network. This might include the number of receive buffers (and even their size) or may be a receive queue parameter (which indirectly controls the number of receive buffers).
The receive resources may need to be increased to handle peak bursts on the network. The network interface device driver places incoming packets on a receive queue. If the receive queue is full, packets are dropped and lost, resulting in the sender needing to retransmit. The receive queue is tunable using the SMIT or chdev commands (see How to Change the Parameters). The maximum queue size is specified to each type of communication adapter (see Tuning MCA and PCI Adapters).
For the Micro Channel adapters and the PCI adapters, receive queue parameters typically control the number of receive buffers that are provided to the adapter for receiving input packets.
AIX 4.1.4 and later support device-specific mbufs. This allows a driver to allocate its own private set of buffers and have them pre-setup for Direct Memory Access (DMA). This can provide additional performance because the overhead to set up the DMA mapping is done one time. Also, the adapter can allocate buffer sizes that are best suited to its MTU size. For example, ATM, High Performance Parallel Interface (HIPPI), and the SP switch support a 64 K MTU (packet) size. The maximum system mbuf size is 16 KB. By allowing the adapter to have 64 KB buffers, large 64 K writes from applications can be copied directly into the 64 KB buffers owned by the adapter, instead of copying them into multiple 16 K buffers (which has more overhead to allocate and free the extra buffers).
The adapters that support Device Specific mbufs are:
Device-specific buffers add an extra layer of complexity for the system administrator. The system administrator must use device-specific commands to view the statistics relating to the adapter's buffers and then change the adapter's parameters as necessary. If the statistics indicate that packets were discarded because not enough buffer resources were available, then those buffer sizes need to be increased.
Due to differences between drivers and the utilities used to alter these parameters, the utilities and parameters are not fully described here. The MCA ATM parameters are listed in Micro Channel Adapter (MCA). Use the atmstat -d atm0 command to view the ATM statistics (substitute your ATM interface number as needed).
Following are some guidelines to help you determine when to increase the receive/transmit queue parameters:
Several status utilities can be used to show the transmit queue high-water limits and number of queue overflows. You can use the command netstat -v, or go directly to the adapter statistics utilities (entstat for Ethernet, tokstat for Token-Ring, fddistat for FDDI, atmstat for ATM, and so on).
For an entstat example output, see The entstat Command. Another method is to use the netstat -i utility. If it shows non-zero counts in the Oerrs column for an interface, then this is typically the result of output queue overflows.
You can use the lsattr -E -l adapter-name command or you can use the SMIT command (smitty commodev) to show the adapter configuration.
Different adapters have different names for these variables. For example, they may be named sw_txq_size, tx_que_size, or xmt_que_size for the transmit queue parameter. The receive queue size and receive buffer pool parameters may be named rec_que_size, rx_que_size, or rv_buf4k_min for example.
Following is the output of a lsattr -E -l atm0 command on an IBM PCI 155 Mbs ATM adapter. This output shows the sw_txq_size is set to 250 and the rv_buf4K_min receive buffers set to x30.
# lsattr -E -l atm0 dma_mem 0x400000 N/A False regmem 0x1ff88000 Bus Memory address of Adapter Registers False virtmem 0x1ff90000 Bus Memory address of Adapter Virtual Memory False busintr 3 Bus Interrupt Level False intr_priority 3 Interrupt Priority False use_alt_addr no Enable ALTERNATE ATM MAC address True alt_addr 0x0 ALTERNATE ATM MAC address (12 hex digits) True sw_txq_size 250 Software Transmit Queue size True max_vc 1024 Maximum Number of VCs Needed True min_vc 32 Minimum Guaranteed VCs Supported True rv_buf4k_min 0x30 Minimum 4K-byte pre-mapped receive buffers True interface_type 0 Sonet or SDH interface True adapter_clock 1 Provide SONET Clock True uni_vers auto_detect N/A True
Following is an example of a Micro Channel 10/100 Ethernet settings using the lsattr -E -l ent0 command. This output shows the tx_que_size and rx_que_size both set to 256.
# lsattr -E -l ent0 bus_intr_lvl 11 Bus interrupt level False intr_priority 3 Interrupt priority False dma_bus_mem 0x7a0000 Address of bus memory used for DMA False bus_io_addr 0x2000 Bus I/O address False dma_lvl 7 DMA arbitration level False tx_que_size 256 TRANSMIT queue size True rx_que_size 256 RECEIVE queue size True use_alt_addr no Enable ALTERNATE ETHERNET address True alt_addr 0x ALTERNATE ETHERNET address True media_speed 100_Full_Duplex Media Speed True ip_gap 96 Inter-Packet Gap True
The following are some of the parameters that are user-configurable:
The device driver supports a user-configurable transmit queue. This is the queue the adapter uses (not an extension of the adapter's queue). It is configurable among the values of 16, 32, 64, 128 and 256, with a default of 256.
Because of the configurable size of the adapter's hardware queue, the driver does not support a software queue.
The device driver supports a user-configurable receive queue. This is the queue the adapter uses (not an extension of the adapter's queue). It is configurable among the values of 16, 32, 64, 128 and 256, with a default of 256.
The device driver supports a user-configurable receive buffer pool size. The buffer is the number of preallocated mbufs for receiving packets. The minimum size of the buffer is the receive queue size and the maximum is 2 KB (the default value of 384).
The device driver supports speeds of 10 (10 Mbps, half-duplex), 20 (10 Mbps, full-duplex), 100 (100 Mbps, half-duplex), 200 (100 Mbps, full-duplex), and auto-negotiate on twisted pair. On the AUI port, the device driver supports speeds of 10 (10 Mbps, half-duplex) and 20 (10 Mbps, full-duplex). The bayonet Niell-Concelman (BNC) port will only support 10 (10 Mbps, half-duplex). This attribute is user-configurable, with a default of auto-negotiate on twisted pair.
The device driver supports a configuration option to toggle use of an alternate network address. The values are yes and no, with a default of no. When this value is set to yes, the alt_addr parameter defines the address.
For the network address, the device driver accepts the adapter's hardware address or a configured alternate network address. When the use_alt_addr configuration option is set to yes, this alternate address is used. Any valid individual address can be used, but a multicast address cannot be defined as a network address.
The inter-packet gap (IPG) bit rate setting controls the aggressiveness of the adapter on the network. A smaller number will increase the aggressiveness of the adapter, while a larger number will decrease the aggressiveness (and increase the fairness) of the adapter. If the adapter statistics show a large number of collisions and deferrals, increase this number. Valid values range from 96 to 252, in increments of 4. The default value of 96 results in IPG of 9.6 microseconds for 10 Mb and 0.96 microseconds for 100 Mb media speeds. Each unit of bit rate introduces an IPG of 100 ns at 10 Mb and 10 ns at 100 Mb media speed.
To change any of the parameter values, do the following:
# ifconfig en0 detach
where en0 represents the adapter name.
# ifconfig en0 hosthame upAn alternative method to change these parameter values is to run the following command:
# chdev -l [ifname] -a [attribute-name]=newvalue
For example, to change the above tx_que_size on en0 to 128, use the following sequence of commands. Note that this driver only supports four different sizes, so it is better to use the SMIT command to see these values.
# ifconfig en0 detach
# chdev -l ent0 -a tx_que_size=128
# ifconfig en0 hostname up
The following information is provided to document the various adapter-tuning parameters. These parameters and values are for AIX 4.3.1 and are provided to aid you in understanding the various tuning parameters, or when a system is not available to view the parameters.
These parameter names, defaults, and range values were obtained from the ODM database. The comment field was obtained from the lsattr -E -l interface-name command.
The Notes field provides additional comments.
Feature Code: 2980 Ethernet High-Performance LAN Adapter (8ef5) Parameter Default Range Comment Notes ------------- -------- -------- --------------------------- ----------------- xmt_que_size 512 20-2048 TRANSMIT queue size SW TX queue rec_que_size 30 20-150 RECEIVE queue size See Note 1 rec_pool_size 37 16-64 RECEIVE buffer pool size On Adapter Feature Code: 2992 Ethernet High-Performance LAN Adapter (8f95) Parameter Default Range Comment Notes ------------- --------- -------- ------------------- ---------- xmt_que_size 512 20-2048 TRANSMIT queue size SW queue Feature Code: 2994 IBM 10/100 Mbps Ethernet TX MCA Adapter (8f62) Parameter Default Range Comment Notes ------------- -------- ---------------- --------------------- ----------- tx_que_size 64 16,32,64,128,256 TRANSMIT queue size HW queue rx_que_size 32 16,32,64,128,256 RECEIVE queue size HW queue Feature Code: 2970 Token-Ring High-Performance Adapter (8fc8) Parameter Default Range Comment Notes ------------- -------- -------- --------------------- ------------ xmt_que_size 99 32-2048 TRANSMIT queue size SW queue rec_que_size 30 20-150 RECEIVE queue size See Note 1 Feature Code: 2972 Token-Ring High-Performance Adapter (8fa2) Parameter Default Range Comment Notes ------------- -------- -------- ---------------------------- ---------- xmt_que_size 512 32-2048 TRANSMIT queue size SW queue rx_que_size 32 32-160 HARDWARE RECEIVE queue size HW queue Feature Code: 2727 FDDI Primary Card, Single Ring Fiber Parameter Default Range Comment Notes ------------- -------- -------- ------------------------------ -------------------- tx_que_size 512 3-2048 Transmit Queue Size (in mbufs) rcv_que_size 30 20-150 Receive Queue See Note 1 Feature Code: 2984 100 Mbps ATM Fiber Adapter (8f7f) Parameter Default Range Comment Notes --------------- ----- --------- -------------------------- ----- sw_queue 512 0-2048 Software transmit queue len. SW Queue dma_bus_width 0x1000000 0x800000-0x40000000,0x100000 Amount of memory to map for DMA See Note 3 max_sml_bufs 50 40-400 Maximum Small ATM mbufs Max 256 byte buffers max_med_bufs 100 40-1000 Maximum Medium ATM mbufs Max 4KB buffers max_lrg_bufs 300 75-1000 Maximum Large ATM mbufs Max 8KB buffers See Note 2 max_hug_bufs 50 0-400 Maximum Huge ATM mbufs Max 16KB buffers max_spec_bufs 4 0-400 Maximum ATM MTB mbufs Max of max_spec_buf size spec_buf_size 64 32-1024 Max Transmit Block (MTB) size (kbytes) sml_highwater 20 10-200 Minimum Small ATM mbufs Min 256 byte buffers med_highwater 30 20-300 Minimum Medium ATM mbufs Min 4KB buffers lrg_highwater 70 65-400 Minimum Large ATM mbufs Min 8KB buffers hug_highwater 10 4-300 Minimum Huge ATM mbufs Min 16KB buffers spec_highwater 20 0-300 Minimum ATM MTB mbufs Min 64KB buffers best_peak_rate 1500 1-155000 Virtual Circuit Peak Segamentation Rate Feature Code: 2989 155 Mbps ATM Fiber Adapter (8f67) Parameter Default Range Comment Notes ------------- -------- -------- ---------- ------- (same as ATM 100 adapter above)
This queue is not used by the typical TCP/IP stack.
The other buffers sizes are only for transmit buffers.
Feature Code 2985
IBM PCI Ethernet Adapter (22100020)
Parameter Default Range Comment Notes
------------- -------- ----------------- ------------------- ---------
tx_que_size 64 16,32,64,128,256 TRANSMIT queue size HW Queues
rx_que_size 32 16,32,64,128,256 RECEIVE queue size HW Queues
Featue Code 2968
IBM 10/100 Mbps Ethernet PCI Adapter (23100020)
Parameter Default Range Comment Notes
---------------- ------- ---------------- --------------------- --------------------
tx_que_size 256 16,32,64,128,256 TRANSMIT queue size HW Queue Note 1
rx_que_size 256 16,32,64,128,256 RECEIVE queue size HW Queue Note 2
rxbuf_pool_size 384 16-2048 # buffers in receive Dedicat. receive
buffer pool buffers Note 3
Feature Code: 2969
Gigabit Ethernet-SX PCI Adapter (14100401)
Parameter Default Range Comment Notes
------------- ------- -------- ----------------------------------- ---------
tx_que_size 512 512-2048 Software Transmit Queueu size SW Queue
rx_que_size 512 512 Receive queue size HW Queue
receive_proc 6 0-128 Minimum Receive Buffer descriptiors
Feature Code: 2986
3Com 3C905-TX-IBM Fast EtherLink XL NIC
Parameter Default Range Comment Notes
-------------- -------- ------ ---------------------------- ----------
tx_wait_q_size 32 4-128 Driver TX Waiting Queue Size HW Queues
rx_wait_q_size 32 4-128 Driver RX Waiting Queue Size HW Queues
Feature Code: 2742
SysKonnect PCI FDDI Adapter (48110040)
Parameter Default Range Comment Notes
------------- -------- -------- ------------------- ---------------
tx_queue_size 30 3-250 Transmit Queue Size SW Queue
RX_buffer_cnt 42 1-128 Receive frame count Rcv buffer pool
Feature Code: 2979
IBM PCI Tokenring Adapter (14101800)
Parameter Default Range Comment Notes
------------- -------- ------- --------------------------- --------
xmt_que_size 96 32-2048 TRANSMIT queue size SW Queue
rx_que_size 32 32-160 HARDWARE RECEIVE queue size HW queue
Feature Code: 2979
IBM PCI Tokenring Adapter (14103e00)
Parameter Default Range Comment Notes
------------- -------- -------- -------------------- --------
xmt_que_size 512 32-2048 TRANSMIT queue size SW Queue
rx_que_size 64 32-512 RECEIVE queue size HW Queue
Feature Code: 2988
IBM PCI 155 Mbps ATM Adapter (14107c00)
Parameter Default Range Comment Notes
------------- --------- ------------ -------------------------------- --------
sw_txq_size 100 0-4096 Software Transmit Queue size SW Queue
rv_buf4k_min 48 (0x30) 0-512 (x200) Minimum 4K-byte pre-mapped receive buffers
Notes on the IBM 10/100 Mbps Ethernet PCI Adapter:
Drivers, by default, call IP directly, which calls up the protocol stack to the socket level while running on the interrupt level. This minimizes instruction path length, but increases the interrupt hold time. On an SMP system, a single CPU can become the bottleneck for receiving packets from a fast adapter. By enabling the dog threads, the driver queues the incoming packet to the thread and the thread handles calling IP, TCP, and the socket code. The thread can run on other CPUs which may be idle. Enabling the dog threads can increase capacity of the system in some cases.
This is a feature for the input side (receive) of LAN adapters. It can be configured at the interface level with the ifconfig command (ifconfig interface thread or ifconfig interface hostname up thread).
To disable the feature, use the ifconfig interface -thread command.
Guidelines when considering using dog threads are as follows:
The dog threads run best when they find more work on their queue and do not have to go back to sleep (waiting for input). This saves the overhead of the driver waking up the thread and the system dispatching the thread.
The TCP protocol includes a mechanism for both ends of a connection to negotiate the maximum segment size (MSS) to be used over the connection. Each end uses the OPTIONS field in the TCP header to advertise a proposed MSS. The MSS that is chosen is the smaller of the values provided by the two ends.
The purpose of this negotiation is to avoid the delays and throughput reductions caused by fragmentation of the packets when they pass through routers or gateways and reassembly at the destination host.
The value of MSS advertised by the TCP software during connection setup depends on whether the other end is a local system on the same physical network (that is, the systems have the same network number) or whether it is on a different (remote) network.
If the other end of the connection is local, the MSS advertised by TCP is based on the MTU (maximum transfer unit) of the local network interface, as follows:
TCP MSS = MTU - TCP header size - IP header size.
Because this is the largest possible MSS that can be accommodated without IP fragmentation, this value is inherently optimal, so no MSS-tuning is required for local networks.
When the other end of the connection is on a remote network, this operating system's TCP defaults to advertising an MSS of 512 bytes. This conservative value is based on a requirement that all IP routers support an MTU of at least 576 bytes.
The optimal MSS for remote networks is based on the smallest MTU of the intervening networks in the route between source and destination. In general, this is a dynamic quantity and could only be ascertained by some form of path MTU discovery. The TCP protocol, by default, does not provide a mechanism for doing path MTU discovery, which is why a conservative MSS value is the default. However, it is possible to enable the TCP PMTU discovery by using the following command:
# no -o tcp_pmtu_discover=1
MTU path discovery was added to AIX 4.2.1, but the default is off. With AIX 4.3.3 and later, the default is on.
A typical side effect of this setting is to see the routing table increasing (one more entry per each active TCP connection). The no option route_expire should be set to a non-zero value, in order to have any unused cached route entry removed from the table, after route_expire time of inactivity.
While the conservative default is appropriate in the general Internet, it can be unnecessarily restrictive for private Intranets within an administrative domain. In such an environment, MTU sizes of the component physical networks are known, and the minimum MTU and optimal MSS can be determined by the administrator. The operating system provides several ways in which TCP can be persuaded to use this optimal MSS. Both source and destination hosts must support these features. In a heterogeneous, multi-vendor environment, the availability of the feature on both systems can determine the choice of solution.
The default MSS of 512 can be overridden by specifying a static route to a specific remote network. Use the -mtu option of the route command to specify the MTU to that network. In this case, you would specify the actual minimum MTU of the route, rather than calculating an MSS value.
In a small, stable environment, this method allows precise control of MSS on a network-by-network basis. The disadvantages of this approach are as follows:
This parameter is used to set the maximum packet size for communication with remote networks. However, only one value can be set even if there are several adapters with different MTU sizes. The default value of 512 that TCP uses for remote networks can be changed via the no command. This change is a systemwide change.
To override the MSS default specify a value that is the minimum MTU value less 40 to allow for the typical length of the TCP and IP headers.
The size is the same as the MTU for communication across a local network with one exception: the tcp_mssdflt size is only for the size of the data in a packet. Reduce the tcp_mssdflt for the size of any headers so that you send full packets instead of a full packet and a fragment. Calculate this as follows:
MTU of interface - TCP header size - IP header size - rfc1323 header size
which is:
MTU - 20 - 20 - 12, or MTU - 52
Limiting data to (MTU - 52) bytes ensures that, where possible, only full packets will be sent.
In an environment with a larger-than-default MTU, this method has the advantage in that the MSS does not need to be set on a per-network basis. The disadvantages are as follows:
Several physical networks can be made to share the same network number by subnetting. The no option subnetsarelocal specifies, on a systemwide basis, whether subnets are to be considered local or remote networks. With the command no -o subnetsarelocal=1 (the default), Host A on subnet 1 considers Host B on subnet 2 to be on the same physical network.
The consequence is that when Host A and Host B establish a connection, they negotiate the MSS assuming they are on the same network. Each host advertises an MSS based on the MTU of its network interface, usually leading to an optimal MSS being chosen.
The advantages to this approach are as follows:
The disadvantages to this approach are as follows:
UDP is a datagram protocol. Being a datagram, the entire message (datagram) must be copied into the kernel on a send operation as one atomic operation. The maximum amount of data that UDP can send at one time is limited by the size of the memory buffer assigned to a specific UDP socket, and the maximum packet size that the IP layer can handle in each packet.
Set this parameter to 65536, because any value greater than 65536 is ineffective. Because UDP transmits a packet as soon as it gets any data, and because IP has an upper limit of 65536 bytes per packet, anything beyond 65536 runs the small risk of being discarded by IP. The IP protocol will fragment the datagram into smaller packets if needed, based on the MTU size of the interface the packet will be sent on. For example, sending an 8 K datagram, IP would fragment this into 1500 byte packets if sent over Ethernet. Because UDP does not implement any flow control, all packets given to UPD are passed to IP (where they may be fragmented) and then placed directly on the device drivers transmit queue.
On the receive side, the incoming datagram (or fragment if the datagram is larger than the MTU size) will first be received into a buffer by the device driver. This will typically go into a buffer that is large enough to hold the largest possible packet from this device.
The setting of udp_recvspace is harder to compute because it varies by network adapter type, UDP sizes, and number of datagrams queued to the socket. Set the udp_recvspace larger rather than smaller, because packets will be discarded if it is too small.
For example, Ethernet might use 2 K receive buffers. Even if the incoming packet is maximum MTU size of 1500 bytes, it will only use 73 percent of the buffer. IP will queue the incoming fragments until a full UDP datagram is received. It will then be passed to UDP. UDP will put the incoming datagram on the receivers socket. However, if the total buffer space in use on this socket exceeds udp_recvspace, then the entire datagram will be discarded. This is indicated in the output of the netstat -s command as dropped due to full socket buffers errors.
Because the communication subsystem accounts for buffers used, and not the contents of the buffers, you must account for this when setting udp_recvspace. In the above example, the 8 K datagram would be fragmented into 6 packets which would use 6 receive buffers. These will be 2048 byte buffers for Ethernet. So, the total amount of socket buffer consumed by this one 8 K datagram is as follows:
6*2048=12,288 bytes
Thus, you can see that the udp_recvspace must be adjusted higher depending on how efficient the incoming buffering is. This will vary by datagram size and by device driver. Sending a 64 byte datagram would consume a 2 K buffer for each 64 byte datagram.
Then, you must account for the number of datagrams that may be queued onto this one socket. For example, NFS server receives UDP packets at one well-known socket from all clients. If the queue depth of this socket could be 30 packets, then you would use 30 * 12,288 = 368,640 for the udp_recvspace if NFS is using 8 K datagrams. NFS Version 3 allows up to 32K datagrams.
A suggested starting value for udp_recvspace is 10 times the value of udp_sendspace, because UDP may not be able to pass a packet to the application before another one arrives. Also, several nodes can send to one node at the same time. To provide some staging space, this size is set to allow 10 packets to be staged before subsequent packets are discarded. For large parallel applications using UDP, the value may have to be increased.
The following table shows some suggested minimum sizes for socket buffers based on the type of adapter and the MTU size. Note that setting these values too high can hurt performance. In addition, there is the Nagle Black hole problem that can cause very low throughput for large MTU adapters, such as ATM if the TCP send and receive space parameters are not chosen correctly.
| Device | Speed | MTU | tcp_sendspace | tcp_recvspace | sb_max | rfc1323 |
| Ethernet | 10 Mbit | 1500 | 16384 | 16384 | 32768 | 0 |
| Ethernet | 100 Mbit | 1500 | 65536 | 65536 | 65536 | 0 |
| Ethernet | Gigabit | 1500 | 131072 | 65536 | 131072 | 0 |
| Ethernet | Gigabit | 9000 | 131072 | 65535 (Note 1) | 262144 | 0 |
| Ethernet | Gigabit | 9000 | 262144 | 131072 (Note 1) | 524288 | 1 |
| ATM | 155 Mbit | 1500 | 16384 | 16384 | 131072 | 0 |
| ATM | 155 Mbit | 9180 | 65535 | 65535 (Note 2) | 131072 | 0 |
| ATM | 155 Mbit | 65527 | 655360 | 655360 (Note 3) | 1310720 | 1 |
| FDDI | 100 Mbit | 4352 | 45056 | 45056 | 90012 | 0 |
Following are some general guidelines:
The ftp and rcp commands are examples of TCP applications that benefit from tuning the tcp_sendspace and tcp_recvspace variables.
TCP send buffer size can limit how much data the application can send before the application is put to sleep. The TCP socket send buffer is used to buffer the application data in the kernel using mbufs/clusters before it is sent beyond the socket and TCP layer. The default size of this buffer is specified by the parameter tcp_sendspace, but you can use the setsockopt() subroutine to override it.
If the amount of data that the application wants to send is smaller than the send buffer size and also smaller than the maximum segment size and if TCP_NODELAY is not set, then TCP will delay up to 200 ms, until enough data exists to fill the send buffer or the amount of data is greater than or equal to the maximum segment size, before transmitting the packets.
If TCP_NODELAY is set, then the data is sent immediately (useful for request/response type of applications). If the send buffer size is less than or equal to the maximum segment size (ATM and SP switches can have 64 K MTUs), then the application's data will be sent immediately and the application must wait for an ACK before sending another packet (this prevents TCP streaming and could reduce throughput).
If an application does nonblocking I/O (specified O_NDELAY or O_NONBLOCK on the socket), then if the send buffer fills up, the application will return with an EWOULDBLOCK/EAGAIN error rather than being put to sleep. Applications must be coded to handle this error (suggested solution is to sleep for a short while and try to send again).
When you are changing send/recv space values, in some cases you must stop/restart the inetd process as follows:
# stopsrc -s inetd; startsrc -s inetd
TCP receive-buffer size limits how much data the receiving system can buffer before the application reads the data. The TCP receive buffer is used to accommodate incoming data. When the data is read by the TCP layer, TCP can send back an acknowledgment (ACK) for that packet immediately or it can delay before sending the ACK. Also, TCP tries to piggyback the ACK if a data packet was being sent back anyway. If multiple packets are coming in and can be stored in the receive buffer, TCP can acknowledge all of these packets with one ACK. Along with the ACK, TCP returns a window advertisement to the sending system telling it how much room remains in the receive buffer. If not enough room remains, the sender will be blocked until the application has read the data. Smaller values will cause the sender to block more. The size of the TCP receive buffer can be set using the setsockopt() subroutine or by the tcp_recvspace parameter.
The TCP window size by default is limited to 65536 bytes (64 K) but can be set higher if rfc1323 is set to 1. If you are setting tcp_recvspace to greater than 65536, set rfc1323=1 on each side of the connection. Without having rfc1323 set on both sides, the effective value for tcp_recvspace will be 65536.
If you are sending data through adapters that have large MTU sizes (32 K or 64 K for example), TCP streaming performance may not be optimal because the packet or packets will be sent and the sender will have to wait for an acknowledgment. By enabling the rfc1323 option using the command no -o rfc1323=1, TCP's window size can be set as high as 4 GB. However, on adapters that have 64 K or larger MTUs, TCP streaming performance can be degraded if the receive buffer can only hold 64 K. If the receiving machine does not support rfc1323, then reducing the MTU size is one way to enhance streaming performance.
After setting the rfc1323 option to 1, you can increase the tcp_recvspace parameter to something much larger, such as 10 times the size of the MTU.
This parameter controls how much buffer space is consumed by buffers that are queued to a sender's socket or to a receiver's socket. The system accounts for socket buffers used based on the size of the buffer, not on the contents of the buffer.
If a device driver puts 100 bytes of data into a 2048-byte buffer, then the system considers 2048 bytes of socket buffer space to be used. It is common for device drivers to receive buffers into a buffer that is large enough to receive the adapters maximum size packet. This often results in wasted buffer space but it would require more CPU cycles to copy the data to smaller buffers.
Because there are so many different network device drivers, increase the sb_max value much higher rather than making it the same as the largest TCP or UDP socket buffer size parameters. After the total number of mbufs/clusters on the socket reaches the sb_max limit, no additional buffers can be queued to the socket until the application has read the data.
One guideline would be to set it to twice as large as the largest TCP or UDP receive space.
In AIX 4.3.3, a feature called Interface-Specific Network Options (ISNO) was introduced that allows IP network interfaces to be custom-tuned for the best performance. Values set for an individual interface take precedence over the systemwide values set with the no command. The feature is enabled (the default) or disabled for the whole system with the no command use_isno option. This single-point ISNO disable option is included as a diagnostic tool to eliminate potential tuning errors if the system administrator needs to isolate performance problems.
Programmers and performance analysts should note that the ISNO values will not show up in the socket (meaning they cannot be read by the getsockopt() system call) until after the TCP connection is made. The interface this socket will actually be using is not known until the connection is complete, so the socket reflects the system defaults from the no command. After the connection is accepted, ISNO values are put into the socket.
The following five parameters have been added for each supported network interface:
When set for a specific interface, these values override the corresponding no option values set for the system. These parameters are available for all of the mainstream TCP/IP interfaces (Token-Ring, FDDI, 10/100 Ethernet, and Gigabit Ethernet), except the css# IP interface on the SP switch. As a simple workaround, SP switch users can set the tuning options appropriate for the switch using the systemwide no command, then use the ISNOs to set the values needed for the other system interfaces. ATM is supported and works correctly with AIX 4.3.3 (a software update is needed) and later.
These options are set for the TCP/IP interface (such as en0 or tr0), and not the network adapter (ent0 or tok0).
The five new ISNO parameters cannot be displayed or changed using SMIT. Following are commands that can be used first to verify system and interface support and then to set and verify the new values.
# no -a | grep isno use_isno = 1
# lsattr -E -l en0 -H attribute value description user_settable : rfc1323 N/A True tcp_nodelay N/A True tcp_sendspace N/A True tcp_recvspace N/A True tcp_mssdflt N/A True
For example, to set the tcp_recvspace and tcp_sendspace to 64K and enable tcp_nodelay, use one of the following methods:
# ifconfig en0 tcp_recvspace 65536 tcp_sendspace 65536 tcp_nodelay 1
or
# chdev -l en0 -a tcp_recvspace=65536 -a tcp_sendspace=65536 -a tcp_nodelay=1
# ifconfig en0
en0: flags=e080863<UP,BROADCAST,NOTRAILERS,RUNNING,SIMPLEX,MULTICAST,GROUPRT,64BIT>
inet 9.19.161.100 netmask 0xffffff00 broadcast 9.19.161.255
tcp_sendspace 65536 tcp_recvspace 65536 tcp_nodelay 1
or
# lsattr -El en0 rfc1323 N/A True tcp_nodelay 1 N/A True tcp_sendspace 65536 N/A True tcp_recvspace 65536 N/A True tcp_mssdflt N/A True
At the IP layer, the only tunable parameter is ipqmaxlen, which controls the length of the IP input queue discussed in IP Layer. In AIX Version 4, in general, interfaces do not do queuing. Packets can arrive very quickly and overrun the IP input queue. You can use the netstat -s or netstat -p ip command to view an overflow counter (ipintrq overflows).
If the number returned is greater than 0, overflows have occurred. Use the no command to set the maximum length of this queue. For example:
# no -o ipqmaxlen=100
This example allows 100 packets to be queued up. The exact value to use is determined by the maximum burst rate received. If this cannot be determined, using the number of overflows can help determine what the increase should be. No additional memory is used by increasing the queue length. However, an increase may result in more time spent in the off-level interrupt handler, because IP will have more packets to process on its input queue. This could adversely affect processes needing CPU time. The tradeoff is reduced packet-dropping versus CPU availability for other processing. It is best to increase ipqmaxlen by moderate increments if the tradeoff is a concern in your environment.
Ethernet is one of the contributors to the "least common denominator" algorithm of MTU choice. If a configuration includes Ethernets and other LANs, and there is extensive traffic among them, the MTUs of all of the LANs may need to be set to 1500 bytes to avoid fragmentation when data enters an Ethernet. Following are some guidelines:
The default MTU of 1492 bytes is appropriate for Token-Rings that interconnect to Ethernets or to heterogeneous networks in which the minimum MTU is not known. Following are some guidelines:
The default MTU of 1492 bytes is appropriate for Token-Rings that interconnect to Ethernets or to heterogeneous networks in which the minimum MTU is not known. Following are some guidelines:
Despite the comparatively low MTU, this high-speed medium benefits from substantial increases in socket buffer size. Following are some guidelines:
Following are some guidelines:
Following are some guidelines:
Following are some guidelines: