[ Previous | Next | Contents | Glossary | Home | Search ]
AIX Version 4.3 Messages Guide and Reference

List of Three-Digit Display Values: 100-195

Display Value 100

Explanation Progress indicator. Built-in self-test completed successfully.
System Action Control was passed to IPL ROM.
User Action If the system halts with this value displayed, record SRN 101-100 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 101

Explanation Progress indicator. Initial built-in self-test started following system reset.
System Action Built-in self-test running.
User Action If the system halts with this value displayed, record SRN 101-101 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 102

Explanation Progress indicator. Built-in self-test started following power-on reset.
System Action Built-in self-test running.
User Action If the system halts with this value displayed, record SRN 101-102 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 103

Explanation Built-in self-test could not determine the system model number.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-103 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 104

Explanation Built-in self-test could not find the common on-chip processor bus address.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-104 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 105

Explanation Built-in self-test could not read from the on-chip sequencer EPROM.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-105 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value106

Explanation Built-in self-test detected a module failure.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-106 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 111

Explanation On-chip sequencer stopped; BIST detected a module error.
System Action The system halts.
User Action Follow the steps for a flashing 888. Go to "888 in the Three-Digit Display" .

Display Value 112

Explanation Checkstop occurred during built-in self-test and checkstop results could not be logged out.
System Action The system attempted to save the failure data associated with the checkstop into NVRAM but was unsuccessful. The system halts.
User Action If the system halts with this value displayed, record SRN 101-112 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 113

Explanation The built-in self-test checkstop count equals 3.
System Action The checkstop count is initialized to 0 (zero) whenever the system is turned on. When a checkstop occurs, the checkstop count is increased and a system restart begins automatically. If the system restart is successful, the operating system records the checkstop in the system error log and resets the checkstop count to 0. If three consecutive checkstops occur without a system restart completing successfully, the system halts.
User Action If the system halts with this value displayed, record SRN 101-113 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 120

Explanation Progress indicator. Built-in self-test started cyclic redundancy-check character (CRC) check on the 8752 EPROM.
System Action Built-in self-test running.
User Action If the system halts with this value displayed, record SRN 101-120 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 121

Explanation Built-in self-test detected a bad CRC on the on-chip sequencer EPROM.
System Action Built-in self-test running.
User Action If the system halts with this value displayed, record SRN 101-121 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 122

Explanation Progress indicator. Built-in self-test started CRC check on the on-chip sequencer EPROM.
System Action Built-in self-test running.
User Action If the system halts with this value displayed, record SRN 101-122 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 123

Explanation Built-in self-test detected a bad CRC on the on-chip sequencer NVRAM.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-123 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 124

Explanation Progress indicator. Built-in self-test started CRC check on the on-chip sequencer NVRAM.
System Action Built-in self-test running.
User Action If the system halts with this value displayed, record SRN 101-124 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 125

Explanation Built-in self-test detected a bad CRC on the time-of-day NVRAM.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-125 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 126

Explanation Progress indicator. Built-in self-test started CRC check on the time-of-day NVRAM.
System Action Built-in self-test running.
User Action If the system halts with this value displayed, record SRN 101-126 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 127

Explanation Built-in self-test detected a bad CRC on the 8752 EPROM.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-127 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 130

Explanation Progress indicator. Built-in self-test presence test started.
System Action Built-in self-test running.
User Action If the system halts with this value displayed, then the built-in self-test has detected a problem with the Reset button. Record SRN 101-130 in item 4 on the Problem Summary Form, and report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 140

Explanation Built-in self-test was unsuccessful.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-140 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 142

Explanation Built-in self-test was unsuccessful.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-142 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 143

Explanation Invalid memory configuration.

Display Value 144

Explanation Built-in self-test was unsuccessful.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-144 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 151

Explanation Progress indicator. Built-in self-test started array-initialization program test code.
System Action Built-in self-test running.
User Action If the system halts with this value displayed, record SRN 101-151 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 152

Explanation Progress indicator. Built-in self-test started direct-current logic self-test (DCLST) test code.
System Action Built-in self-test running.
User Action If the system halts with this value displayed, record SRN 101-152 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 153

Explanation Progress indicator. Built-in self-test started alternating-current logic self-test (ACLST) test code.
System Action Built-in self-test running.
User Action If the system halts with this value displayed, record SRN 101-153 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 154

Explanation Progress indicator. Built-in self-test started array self-test (AST) test code.
System Action Built-in self-test running.
User Action If the system halts with this value displayed, record SRN 101-154 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 160

Explanation The built-in self-test detected a missing Early Power-Off Warning (EPOW) connector.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-160 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 161

Explanation The Bump quick I/O tests failed.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-161 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 162

Explanation The JTAG tests failed.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-161 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 164

Explanation The built-in self-test encountered an error while reading low NVRAM.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-164 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 165

Explanation The built-in self-test encountered an error while writing low NVRAM.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-165 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 166

Explanation The built-in self-test encountered an error while reading high NVRAM.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-166 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 167

Explanation The built-in self-test encountered an error while writing high NVRAM.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-167 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value168

Explanation The built-in self-test encountered an error while reading the serial input/output (SIO) register.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-168 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 169

Explanation The built-in self-test encountered an error while writing the serial input/output (SIO) register.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-169 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 180

Explanation Progress indicator. Built-in self-test checkstop logout in progress.
System Action The system is saving checkstop failure data into NVRAM.
User Action If the system halts with this value displayed for more than two minutes, record SRN 101-180 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 182

Explanation The built-in self-test COP bus is not responding.

Display Value 185

Explanation Checkstop occurred during built-in self-test.
System Action Built-in self-test running.
User Action If the system halts with this value displayed, record SRN 101-185 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 186

Explanation System logic-generated checkstop (Model 250 only).
System Action Built-in self-test running.
User Action If the system halts with this value displayed, record SRN 101-186 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value 187

Explanation The built-in self-test was unable to identify the chip release level in the checkstop logout data.
System Action The system halts.
User Action If the system halts with this value displayed, record SRN 101-187 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.

Display Value195

Explanation Progress indicator. Built-in self-test checkstop logout completed.
System Action The system successfully saved checkstop failure data into NVRAM.
User Action If the system halts with this value displayed, record SRN 101-195 in item 4 on the Problem Summary Form. Report the problem to your hardware service organization, and then stop. You have completed these procedures.
[ Previous | Next | Contents | Glossary | Home | Search ]