[ Previous | Next | Contents | Glossary | Home | Search ]
AIX Version 4.3 Messages Guide and Reference

List of Three-Digit Display Values: 0c0-0cc

Display Value 0c0

Explanation A user-requested dump completed successfully.
System Action System dump completed. The system halts.
User Action To retrieve the system dump, go to "System Dump Facility" in in AIX Problem Solving Guide and Reference.

Display Value 0c1

Explanation An I/O error occurred during the dump.
System Action System dump completed. The system halts.
User Action To retrieve the system dump, go to "System Dump Facility" in in AIX Problem Solving Guide and Reference. However, the dump is a partial dump. Complete the Problem Summary Form, and report the problem to your software service department.

Display Value 0c2

Explanation A user-requested dump is in progress.
System Action Writing a system dump.
User Action A dump started by the system did not complete. Wait at least 1 minute for the dump to complete and for the three-digit display value to change. If the three-digit display values changes, find the new value on this list. If the value does not change, then the dump did not complete due to an unexpected error. Complete the Problem Summary Form, and report the problem to your software service department.

Display Value 0c4

Explanation The dump ran out of space.
System Action Partial system dump completed. The system halts.
User Action To retrieve the system dump, go to "System Dump Facility" in in AIX Problem Solving Guide and Reference. However, the dump is a partial dump. This probably means your dump device is not large enough.

Display Value 0c5

Explanation The dump failed due to an internal error.
System Action System dump attempted and failed. The system halts.
User Action To retrieve the system dump, go to "System Dump Facility" in in AIX Problem Solving Guide and Reference. The dump may be a partial dump. Complete the Problem Summary Form, and report the problem to your software service department.

Display Value 0c7

Explanation Progress indicator. Remote dump in progress.
System Action The dump routine has written a packet of information to the server containing the dump file and is waiting for the server to respond. When the server responds, the dump routine changes the three-digit display code to 0c2 or 0c9 and prepares the next packet. Each time a packet is transmitted, the dump routine changes the three-digit display to 0c7 while waiting for the host to respond. The three-digit display alternates between 0c7 and 0c2 or between 0c7 and 0c9 until the system dump is complete.
User Action A network dump is in progress, and the host is waiting for the server to respond. The value in the three-digit display should alternate between 0c2 and 0c7. If the value does not change, then the dump did not complete due to an unexpected error. Complete the Problem Summary Form, and report the problem to your software service department.

Display Value 0c8

Explanation The dump device is disabled. The current system configuration does not designate a device for the requested dump.
System Action The system dump cannot be completed. The system halts.
User Action Complete the Problem Summary Form, and report the problem to your software service department.

Display Value 0c9

Explanation A system-initiated dump has started.
System Action Partial dump completed.
User Action A dump started by the system is in progress. Wait at least 1 minute for the dump to complete and for the three-digit display value to change. If the three-digit display values changes, find the new value on this list. If the value does not change, then the dump did not complete due to an unexpected error. Complete the Problem Summary Form, and report the problem to your software service department.

Display Value 0cc

Note: For AIX 4.2.1 and later only.

Explanation An error occurred dumping to the primary dump device, and we've switched over to the secondary dump device.
System Action Writing a system dump.
User Action A dump started by the system is in progress. Wait at least 1 minute for the dump to complete and for the three-digit display value to change. If the three-digit display value changes, find the new value on this list. If the value does not change, then the dump did not complete due to an unexpected error. Complete the Problem Summary Form, and report the problem to your software service department.
[ Previous | Next | Contents | Glossary | Home | Search ]