Adapter ID

8DF0, 8DF1, 8DF2, 8DF3, 8DF4, 8DF5, 8DF6

Name

8DF0 : IBM Image Adapter/A

8DF1 : IBM Image Adapter/A with Printer/Scanner Option

8DF2 : DSS and sub card 2

8DF3 : DSS and sub card 3

8DF4 : IBM Image Adapter/A

8DF5 : IBM Image Adapter/A and Printer/Scanner Option

8DF6 : IBM Image-I Adapter

Class

VID  Video

Origin

IBM

P/N

Part Name	FRU P/N	MKT P/N
Image Adapter/A 1MB	06G8224 *	35G4715
Image Adapter/A 3MB	66G2279 *	35G4716
Image Adapter/A 3MB and 6091-Cable		35G4717
6091-019 Video Cable	58F2902
Memory Module-DRAM **	07F4407
Memory Module-VRAM	75X5894
Printer/Scanner Feature Card	07F4403
Printer/Scanner Y-Cable	07F4417
OEM Scanner Cable (25-Pin male-male)	58F4411
3812-002 Printer Cable	07F4413
4216-020 Printer Cable	07F2474

* 8550, 8555, 8560, 8570, 8580, 8595 only.
** Not for 8565, 8573, 9047.

Video Cables for Displays

Display Type	Cable Description	MKT P/N
6091-016 6091-19i	IBM SIMM cable (SIMM connector to 5BNC)	49G2717
6091-019	See note below
9517 1091-051	IBM Connector Converter Cable	49G2718
1091-051	No special cable needed	--
9527	IBM SIMM Cable	95G9906
9521	IBM SIMM Cable	95G9907

6091-019 Display Cable

This cable is required if the Image Adapter/A or the Image-I Adapter/A is supporting an IBM Color Display 6019-019. The cable is supplied with the Image Adapter/A 3MB 6019. The cable (FRU 58F2902) must be ordered separately for all others.

Copyright Notice

Technical information and illustrations contained in this page are edited excerpts from the EPRM, Copyright © IBM Corp. 1992-97.

Image Adapter/A

The Image Adapter/A is a high-resolution adapter, capable of driving displays up to 128 MHz, with a maximum screen addressability of 1600x1200 pixels. The driver output impedance for video signals is 75 ohms. The sync lines of the adapter are TTL levels driven by 4 ma drivers, therefore the termination should at the very least be at 750 ohms.

The Image Adapter/A is available in three versions:

• The Image Adapter/A 1MB is available with one megabyte of Video Memory (VRAM). It can be upgraded to three megabyte of VRAM and the Image Adapter/A Memory Expansion Kit.
• The Image Adapter/A 3MB has two megabytes of VRAM and the Image Adapter/A Memory Expansion Kit already installed.
• The Image Adapter/A 3MB 6091 is the same as the Image Adapter/A 3MB, but also has a cable for attaching an IBM 6019-019 Color Display.

The three versions of the Image Adapter/A support IBM analog displays equipped with a 15-pin direct-drive analog interface. The adapters can be installed in any IBM PS/2 Micro Channel system unit, except portable models.

Image Adapter/A Options

You can attach optional features only to the Image Adapter/A.

• Printer/Scanner Option.
• Memory Expansion Kit.
• PS/2 Video Memory Expansion Option.

For a single display configuration, you must always attach the display to the display connector on the Image Adapter/A and not to the system-unit display connector.

Image Adapter/A 15-pin Analog Video Connector

Pin Color Mode Monochrome Mode 1 Red Video Reserved 2 Green Video Video 3 Blue Video Reserved 4 Display ID 2 Display ID 2 5 Self-Test Self-Test 6 Red Ground Reserved 7 Green Ground Video Ground 8 Blue Ground Reserved 9 +12V fused +12V fused 10 Digital Ground Digital Ground 11 Display ID 0 Display ID 0 12 Display ID 1 Display ID 0 13 External Hsync External Hsync 14 External Vsync External Vsync 15 Display ID 3 Display ID 3

Image-I Adapter/A

The Image-I Adapter/A is a high-resolution adapter, capable of driving displays up to 230 MHz, with a maximum screen addressability of 1600x1280 pixels. It is available in 3MB only. It is ISO (International Organization for Standardization) enabled. The Image-I Adapter/A supports only ISO refresh rates, it does not support non-ISO displays.

The Image-I Adapter/A can be installed in all IBM PS/2 system units except portable models. ISO-enabled IBM display types are 6091-016, 6091-19i, 1091-051, 4517 and the 9504 Monochrome Display. These displays conform with industry and government standards, such as ISO standard 9241/3.

The display attached to the Image Adapter can show VGA graphics only if the adapter is installed in the AVEC slot. Ideally, the Image Adapter should be installed in the AVEC slot unless this slot is already in use (e.g. with an 8514/A Adapter).

SIM-Video Connector

Image-I Adapter/A SIM-Video Connector:

Pin Type No Serial Interface Serial Interface Captured Cable C1 Coax Red BNC Red 75 Ohm Terminator C2 Coax Green BNC Green 75 Ohm Terminator C3 Coax Blue BNC Blue 75 Ohm Terminator 1 TP ID Pin 2 ID Pin 2 2 TP ID Pin 1 ID Pin 1 / Clk Out 3 TP   H.V.S.D. 4 Coax Digital Ground Digital Ground 5 Coax Hsync BNC Hsync 6 TP ID Pin 4 ID Pin 4 7 TP ID Pin 3 ID Pin 3 / Data 8 TP     9 Coax Vsync BNC Vsync 10 Coax Digital Ground Digital Ground

@8DF0.ADF  IBM Image Adapter/A

@8DF1.ADF  IBM Image Adapter/A with Printer/Scanner Option

@8DF2.ADF  DSS and sub card 2

@8DF3.ADF  DSS and sub card 3

@8DF4.ADF  IBM Image Adapter/A

@8DF5.ADF  IBM Image Adapter/A with Printer/Scanner Option

@8DF6.ADF  IBM Image-I Adapter