The following errors are listed by the module that issues the error. These errors are logged in the AIX error log. Use the AIX command errpt to generate reports from the log.
| CS Module Errors | ||
|---|---|---|
| Error # | Description | Resolution |
| cs001 | Text checksum failed. Reboot the 7318 or check the hardware. | Possible memory error. Power-cycle 7318. If problem persists, report to technical support. |
| cs002 | Insufficient memory to run operating kernel; rebooting. | You do not have enough memory to run this package. Add memory to 7318. |
| cs003 | Operating kernel requires configuration file; rebooting. | Verify accessibility of configuration file. |
| cs004 | Power-up selftest was not run. | None. This is informational only. |
| cs005 | Incorrect operating image for the hardware. | The executable image is not supported on this hardware. Make sure you are booting the executable image for this product. |
| cs006 | Incorrect operating image (P10) for the hardware. | The executable image is not supported on this hardware. Make sure you are booting the executable image for this product. |
| cs007 | Invalid operating image (S20) for the hardware. | The executable image is not supported on this hadware. Make sure you are booting the executable image for this product. |
| Exec Module Errors | ||
|---|---|---|
| Error # | Description | Resolution |
| exec001 | Reboot command issued. | None. This is informational only. |
| exec002 | Relogged previous panic. | Report log entry from panic to technical support. |
| HRS Module Errors | ||
|---|---|---|
| Error # | Description | Resolution |
| hrs001 | Incorrect address type. | Change address type in configuration file section. |
| hrs002 | Incorrect interface type. | Change interface type in configuration file section. |
| hrs003 | Cannot set primary and backup interface the same. | Change one of the interfaces in configuration file section. |
| hrs004 | No reliable server specified. | Specify server in configuration file section. |
| hrs005 | Bad reliable server address. | Change address in configuration file section. |
| hrs006 | No primary host specified. | Define primary host in configuration file section. |
| hrs007 | No backup host specified. | Define backup host in configuration file section. |
| hrs008 | Bad primary host address. | Change address in configuration file section. |
| hrs009 | Bad backup host address. | Change address in configuration file section. |
| hrs010 | Bad backup Internet address. | Change address in configuration file section. |
| hrs011 | Bad backup network mask. | Change network mask in configuration file section. |
| hrs012 | Cannot specify backup network mask without backup Internet address. | Change address in configuration file section. |
| hrs013 | Bad backup gateway address. | Change address in configuration file section. |
| hrs014 | Switch from primary to backup interface. | None required, informational only. |
| Kernel Module Errors | ||
|---|---|---|
| Error # | Description | Resolution |
| kernel001 | Internal error. Kernel asserted. | Try to get an upload and report it to technical support. |
| kernel002 | Bad numeric decode in configuration. | Revise the configuration file. |
| LDT Module Errors | ||
|---|---|---|
| Error # | Description | Resolution |
| ldt001 | Incorrect configuration file transparent print parameters. | Revise configuration file. |
| ldt002 | Incorrect configuration file data in numbered session section. | Revise configuration file. |
| ldt003 | Incorrect configuration file data in hot key entry. | Revise configuration file hot key definitions. |
| ldt004 | Incorrect configuration file data; too many hot keys. | Reduce the number of hot keys defined in configuration file section. |
| Log Module Errors | ||
|---|---|---|
| Error # | Description | Resolution |
| log001 | Host Message. | None required. Informational only. |
| Session Module Errors | ||
|---|---|---|
| Error # | Description | Resolution |
| session001 | SPX link up. | None. This is informational only. |
| session002 | SPX link failed. | Verify the host is online and the Ethernet connection is complete. |
| session003 | SPX link down. | None. This is informational only. |
| session004 | SPX link down; malformed packet. | Report to technical support. |
| session005 | Packet protocol violation. | Report to technical support. |
| session006 | Host credit violation on received data. | Report to technical support. |
| session007 | Host sending incorrect protocol number in packets. | Report to technical support. |
| session008 | Host sending incorrect STREAMS module in open packet. | Report to technical support. |
| session009 | Incorrect lan0 address in configuration. | Change the address in the IPX configuration file section. |
| session010 | Incorrect lan1 address in configuration. | Change the address in the IPX configuration file section. |
| session011 | Incorrect lan2 address in configuration. | Change the address in the IPX configuration file section. |
| session012 | Bad framing type specified for SPX/IPX. | Change the frametype entry in the IPX configuration file section. |
| SIO Module Errors | ||
|---|---|---|
| Error # | Description | Resolution |
| sio001 | Incorrect configuration file entry. | Revise the configuration file. |
| sio002 | Unable to set the configuration file value. | Revise the configuration file. |
| sio003 | No STREAMS resources. | Reduce the number of sessions or services in use. |
| sio004 | Excessive line errors; temporarily disabling port. | Verify the data rate, parity, or character size on the port matches the attached device. Improve the physical connection with the shorter cable or slower data rate. |
| sio005 | Power-on self test failed. | Power-on the cycle unit and re-verify. If the problem continues, stop using the port or return the Connection Station for repair. |
| sio006 | Requested poll time is below the minimum acceptable value. | Change the pollTime value in the port section of the configuration file. |
| SPX Module Errors | ||
|---|---|---|
| Error # | Description | Resolution |
| spx001 | SPX link is disconnected in the transmit timeout routine. | Check the LAN interface and MAC statistics for Etherenet problems. Check for low memory and reduce the load if neccesary. |
| spx002 | SPX link is disconnected because of a bad sequence number. | Report to technical support. |
| spx003 | Interval of 0 is illegal; defaulting. | Change the configuration file in the SPX section. |
| spx004 | Transmit retries of 0 is illegal; defaulting. | Change the configuration file in the SPX section. |
| spx005 | Receive retries of 0 is illegal; defaulting. | Change the configuration file in the SPX section. |