Appendix K: 7318 System Errors

The following errors are listed by the module that issues the error. These errors are logged in the AIX error log. Use the AIX command errpt to generate reports from the log.

CMD Module Errors

CMD Module Errors
Error #	Description:	Resolution:
cmd001	Session number missing from configuration file.	Revise session section number in configuration file.
cmd002	Invalid application in configuration file session section.	Revise application name in session section number in configuration file to be one of the support session types.
cmd003	Module open failed during command session initialization.	Revise configuration file or disable external host accessing device.
cmd004	Not enough memory to complete application initialization.	Simplify configuration file or install more memory in 7318.
cmd005	Configuration file error. Application string too long.	Shorten application entry in configuration file session section.
cmd006	Configuration file error. Too many arguments application string.	Shorten application entry in configuration file session section.
cmd007	Configuration file error. Invalid section.	Revise configuration file.
cmd008	Configuration file error. Invalid device name.	Revise device name in configuration file.
cmd009	Configuration file error. Invalid port number.	Revise port number in configuration file.
cmd010	Configuration file error. Invalid session number.	Revise session section number in configuration file.
cmd011	Configuration file error. Invalid LDT device.	Revise port number in configuration file section.
cmd012	Configuration file error. Attempt to redefine session on port.	Disable console or command section for port.
cmd013	Configuration file error. Port requires command a session.	Add session section to port with application equal to command.
cmd014	Internal error.	Report error number and circumstances to technical support.
cmd015	Configuration file error. Both Kerberos and Passwords are active.	Disable Kerberos or passwords in the configuration file.
cmd016	Configuration file error. No time rules specified.	Add time rule to the configuration file.
cmd017	Configuration file error. Bad effective date for time rules.	Revise time rule in the configuration file.
cmd018	Configuration file error. Bad time zone name for time rule.	Revise time rule in the configuration file.
cmd019	Configuration file error. Bad offset for time rule.	Revise time rule in the configuration file.

CS Module Errors

CS Module Errors
Error #	Description	Resolution
cs001	Text checksum failed. Reboot the 7318 or check the hardware.	Possible memory error. Power-cycle 7318. If problem persists, report to technical support.
cs002	Insufficient memory to run operating kernel; rebooting.	You do not have enough memory to run this package. Add memory to 7318.
cs003	Operating kernel requires configuration file; rebooting.	Verify accessibility of configuration file.
cs004	Powerup selftest was not run.	None. This is informational only.
cs005	Incorrect operating image for the hardware.	The executable image is not supported on this hardware. Make sure you are booting the executable image for this product.
cs006	Incorrect operating image (P10) for the hardware.	The executable image is not supported on this hardware. Make sure you are booting the executable image for this product.
cs007	Invalid operating image (S20) for the hardware.	The executable image is not supported on this hadware. Make sure you are booting the executable image for this product.

Exec Module Errors

Exec Module Errors
Error #	Description	Resolution
exec001	Reboot command issued.	None. This is informational only.
exec002	Relogged previous panic.	Report log entry from panic to technical support.

HRS Module Errors

HRS Module Errors
Error #	Description	Resolution
hrs001	Incorrect address type.	Change address type in configuration file section.
hrs002	Incorrect interface type.	Change interface type in configuration file section.
hrs003	Cannot set primary and backup interface the same.	Change one of the interfaces in configuration file section.
hrs004	No reliable server specified.	Specify server in configuration file section.
hrs005	Bad reliable server address.	Change address in configuration file section.
hrs006	No primary host specified.	Define primary host in configuration file section.
hrs007	No backup host specified.	Define backup host in configuration file section.
hrs008	Bad primary host address.	Change address in configuration file section.
hrs009	Bad backup host address.	Change address in configuration file section.
hrs010	Bad backup Internet address.	Change address in configuration file section.
hrs011	Bad backup network mask.	Change network mask in configuration file section.
hrs012	Cannot specify backup network mask without backup Internet address.	Change address in configuration file section.
hrs013	Bad backup gateway address.	Change address in configuration file section.
hrs014	Switch from primary to backup interface.	None required, informational only.

Kerberos Module Errors

Kerberos Module Errors
Error #	Description	Resolution
kerberos001	Bad enable value. Kerberos is disable.	Change the enable value in the Kerberos section of the configuration file.
kerberos002	No realm specified. Kerberos is disabled.	Change the realm value in the Kerberos section of the configuration.
kerberos003	Missing IP address for authorization server. Kerberos is disabled.	Add the IP address for authorization server in Kerberos section of the configuration file.
kerberos004	Incorrect IP address for authorization server. Kerberos is disabled.	Change the IP address for the authorization server in the Kerberos section of the configuration file.
kerberos005	Incorrect clock synchronization timeout. Using defaults instead.	Change the clock synchronization timeout value in the Kerberos seection of the configuration file.
kerberos006	Incorrect port number for authentication service. Using default instead.	Change the port number in the Kerberos section of the configuration file.
kerberos007	Incorrect port number for kerberized rlogin service. Using default instead.	Change the port number in the Kerberos section of the configuration file.
kerberos008	Incorrect port number for non-encrypted kerberized rlogin service. Using default instead.	Change the port number in the Kerberos section of the configuration file.
kerberos009	Incorrect port number for encrypted kerberized rlogin service. Using defaults instead.	Change the port number in the Kerberos section of the configuration file.
kerberos010	Incorrect ticket life. Using default instead.	Change the ticket life value in the Kerberos section of the configuration file.
kerberos011	Incorrect renewable ticket life. Using default instead.	Change the renewable ticket life value in the Kerberos section of the configuration file.

Kernel Module Errors

Kernel Module Errors
Error #	Description	Resolution
kernel001	Internal error. Kernel asserted.	Try to get an upload and report it to technical support.
kernel002	Bad numeric decode in configuration.	Revise the configuration file.

LDT Module Errors

LDT Module Errors
Error #	Description	Resolution
ldt001	Incorrect configuration file transparent print parameters.	Revise configuration file.
ldt002	Incorrect configuration file data in numbered session section.	Revise configuration file.
ldt003	Incorrect configuration file data in hot key entry.	Revise configuration file hot key definitions.
ldt004	Incorrect configuration file data, too many hot keys.	Reduce the number of hot keys defined in configuration file section.

Log Module Errors

Log Module Errors
Error #	Description	Resolution
log001	Host Message.	None required. Informational only.

PPP Module Errors

PPP Module Errors
Error #	Description	Resolution
ppp001	Incorrect number of PPP sections.	Reduce number of [PPP] sections in configuration file.
ppp002	Incorrect device name.	Change device name in configuration file [PPP] section.
ppp003	Bad source address.	Change source address in configuration file [PPP] section.
ppp004	Bad destination address.	Change destination address in configuration file [PPP] section.
ppp005	Bad inactivity timeout.	Change activity timeout in configuration file [PPP] section.
ppp006	Bad restart timeout.	Change restart timeout in configuration file [PPP] section.
ppp007	Bad maximum number PPP configure request retries.	Change configure request retries in configuration file [PPP] section.
ppp008	Bad maximum number configuration negative acknowledgement retires.	Change configuration negative acknowledgement retries in configuration file [PPP] section.
ppp009	Bad MRU.	Change MRU in configuration file [PPP] section.
ppp010	Bad asynchronous control character map.	Change asynchronous control character map in configuration file [PPP] section.
ppp011	Bad PAP flag.	Change PAP flag in configuration file [PPP] section.
ppp012	Bad magic number negotiation flag.	Change magic number negotiation in configuration file [PPP] section.
ppp013	Bad address-control field compression flag.	Change restart timeout in configuration file [PPP] sectionppp0.
ppp014	Bad protocol field compression flag.	Change protocol field compression flag in configuration file [PPP] section.
ppp015	Bad IP address negotiation flag.	Change IP address negation flag in configuration file [PPP] section.
ppp016	Bad new address flag.	Change new address flag in configuration file [PPP] section.
ppp017	Bad VJ compression flag.	Change VJ compression flag in configuration file [PPP] section.
ppp018	Device open failed.	None.
ppp019	PPP open failed. (possibly out of mememory).	None.
ppp020	Warning: ixon mismatch with async map compensating.	Disable ixon in the port section, stty entry, of the configuration file or change the acc map in the PPP section
ppp021	Warning: ixoff mismatch with async map compensating.	Disable ixoff in the port section, stty entry, of the configuration file or change the acc map in the PPP section.
ppp022	Warning: ixany mismatch with async compensating.	Disable ixany in the port section, stty entry, of the configuration file.
ppp023	Warning: cs8 is disabled; enabling.	Enable cs8 in the port section, stty entry, of the configuration file.
ppp024	PPP IP address option failed.	IP address negotiation is not supported. Change the destination IP address configuration.
ppp025	PPP link up.	None. This is informational only.
ppp026	PPP link down.	None. This is informational only.
ppp027	PPP link down.	None. This is informational only.
ppp028	PPP invalid default source address.	Default source address not 0.0.0.0 or 255.255.255.255.
ppp029	PPP invalid default destination address.	Default destination address not 0.0.0.0 or 255.255.255.255.
ppp030	PPP couldn't get memory for internal structure.	Out of memory.
ppp031	PPP device specified invalid.	Be sure device=com is set in [PPPNN] sections.

Session Module Errors

Session Module Errors
Error #	Description	Resolution
session001	SPX link up.	None. This is informational only.
session002	SPX link failed.	Verify the host is online and the Ethernet connection is complete.
session003	SPX link down.	None. This is informational only.
session004	SPX link down; malformed packet.	Report to technical support.
session005	Packet protocol violation.	Report to technical support.
session006	Host credit violation on received data.	Report to technical support.
session007	Host sending incorrect protocol number in packets.	Report to technical support.
session008	Host sending incorrect STREAMS module in open packet.	Report to technical support.
session009	Incorrect lan0 address in configuration.	Change the address in the IPX configuration file section.
session010	Incorrect lan1 address in configuration.	Change the address in the IPX configuration file section.
session011	Incorrect lan2 address in configuration.	Change the address in the IPX configuration file section.
session012	Bad framing type specified for SPX/IPX.	Change the frametype entry in the IPX configuration file section.

SIO Module Errors

SIO Module Errors
Error #	Description	Resolution
sio001	Incorrect configuration file entry.	Revise the configuration file.
sio002	Unable to set the configuration file value.	Revise the configuration file.
sio003	No STREAMS resources.	Reduce the number of sessions or services in use.
sio004	Excessive line errors; temporarily disabling port.	Verify the data rate, parity, or character size on the port matches the attached device. Improve the physical connection with the shorter cable or slower data rate.
sio005	Power-on self test failed.	Power-on the cycle unit and re-verify. If the problem continues, stop using the port or return the Connection Station for repair.
sio006	Requested poll time is below the minimum accpetable value.	Change the pollTime value in the port section of the configuration file.

SLIP Module Errors

SLIP Module Errors
Error #	Description	Resolution
slip001	Attempt to start more than the maximum number of slip jobs.	Reduce the number of [Slip] sections in the configuration file.
slip002	Incorrect device name.	Change the device name in the configuration file [Slip] section.
slip003	Missing source address.	Provide the source address in the configuration file [Slip] section.
slip004	Incorrect source address.	Change the source address in the configuration file [Slip] section.
slip005	Missing destination address.	Provide the destination address in the configuration file [Slip] section.
slip006	Incorrect destination address.	Change the destination address in the configuration file [Slip] section.
slip007	Incorrect compression option.	Change the compression option in the configuration file [Slip] section.
slip008	Device open failed.	Verify the port functionally. Verify the port is not used by another function.
slip009	SLIP open failed; possibly out of memory.	Reduce the system load.
slip010	Warning: ixon is enabled; disabling.	Disable ixon in the port section, stty entry, of the configuration file or change the acc map in the PPP section
slip011	Warning: ixoff is enabled; disabling.	Disable ixoff in the port section, stty entry, of the configuration file or change the acc map in the PPP section.
slip012	Warning: ixany is enabled; disabling.	Disable ixany in the port section, stty entry, of the configuration file.
slip013	Warning: cs8 is disabled; enabling.	Enable cs8 in the port section, stty entry, of the configuration file.

SPX Module Errors

SPX Module Errors
Error #	Description	Resolution
spx001	SPX link is disconnected in the transmit timeout routine.	Check the LAN interface and MAC statistics for Etherenet problems. Check for low memory and reduce the load if neccesary.
spx002	SPX link is disconnected because of a bad sequence number.	Report to technical support.
spx003	Interval of 0 is illegal; defaulting.	Change the configuration file in the SPX section.
spx004	Transmit retries of 0 is illegal; defaulting.	Change the configuration file in the SPX section.
spx005	Receive retries of 0 is illegal; defaulting.	Change the configuration file in the SPX section.

TCP Module Errors

TCP Module Errors
Error #	Description	Resolution
tcp001	Cannot find route to the default gateway.	Change the gateway address in NVRAM, bootptab, or the configuration file.
tcp002	Attempt to configure local IP address as 0.0.0.0.	Define IP address in NVRAM, bootptab, or the configuration file.
tcp003	Unable to initialize the TCP/IP protocol stack.	Report to technical support.
tcp004	BOOTP record contains no vendor record.	None. This is informational only.
tcp005	Too many static host entries. Ignoring extras.	Reduce the number of hosts defined in the configuration file.
tcp006	Too many name server entries. Ignoring extras.	Reduce the number of name servers defined in the configuration file.
tcp007	Conflicting host and domain names in configuration file.	Change the host name or domain name.
tcp008	Missing nameserver entry.	Change the number of nameservers defined in the configuration file.
tcp009	No nameservers specified for the system.	None. This is informational only.
tcp010	Terminal escape string corrupted.	Change the terminal escape string in the configuartion file.
tcp011	Terminal keymap size is not specified.	Add the keymaps size to the keymap section of the configuration file.
tcp012	Missing keymap section.	Change the number of keymaps defined in the configuration file.
tcp013	Keymap section corrupted.	Change the keymap section in the configuration file.
tcp014	Missing host entry.	Add the host section to the ocnfiguration file or change bhosts value.
tcp015	Bad IP address.	Change the IP address in the configuration file.
tcp016	Illegal frametype specified for the TCP stacks.	Change the frametype value in the TCP section of the configuration file.

Telnetd Module Errors

TCP Module Errors
Error #	Description	Resolution
telnet001	Incorrect number of [Telnetd] sections.	Add the [Telnetd] sections to the configuration file.
telnet002	Incorrect device entry.	Change the device entry in the configuration file [Telnetd] section.
telnet003	No valid devices.	Change the device entry or port numbers in the configuration file [Telnetd] section.
telnet004	Incorrect device name.	Change the device entry in the configuration file [Telnetd] section.
telnet005	Bad port number.	Change the port numbers in the configuration file [Telnetd] section.
telnet006	Bad timeout.	Change the timeout value in the configuration file [Telnetd] section.
telenet007	Bad mode.	Change the mode value in the configuration file [Telnetd] section.
telenet008	Devuce open failed.	Verify the port status and that it is not being used by another function.

TN3270 Errors

Error	Description
TCP_ERR_TERM_ESC_SIZE_CORRUPT	Terminal escape string corrupt.
TCP_ERR_TERM_KEYMAP_SIZE_NOT_SPECIFIED	Terminal keymap size not specified.
TCP_ERR_TERM_MISSING_KEYMAP_SECTION	Missing keymap section.
TCP_ERR_TERM_KEYMAP_SECTION_CORRUPT	Keymap section corrupt.
TCP_ERR_MISSING_HOST_ENTRY	Missing host entry. This message will be generated when the number of [HostNN] sections is less than specified by the `nhosts` entry of the [Hosts] section. The recommended action is to provide the [HostNN] section.
TCP_ERR_INVALID_IPADDR_PARAM	Bad IP address. This message is generated when a [HostNN] section has a `hostaddr` entry with text that does not properly specify an IP address. The recommended action is to provide an IP address in the form: ddd.ddd.ddd.ddd where the `d` parameter is a digit from 0 - 9.

[ Previous | Next | Contents | Home | Search ]