[ Bottom of Page | Previous Page | Next Page | Contents | Index | Library Home |
Legal |
Search ]
Commands Reference, Volume 5
snmpmibd Daemon
Purpose
Starts the snmpmibd dpi2 sub-agent daemon as a background
process.
Syntax
snmpmibd [ -f File ] [ -d [Level] ] [ -h HostName ] [ -c Community ]
Description
The snmpmibd command starts the snmpmibd dpi2 sub-agent. This command may only be issued by a user with
root privileges or by a member of the system group.
The snmpmibd daemon complies with the standard Simple
Network Management Protocol Distributed Protocl Interface Version 2.0 defined
by RFC 1592. It acts as a dpi2 sub-agent to communicate with the dpi2 agent
through dpiPortForTCP.0 (1.3.6.1.4.1.2.2.1.1.1.0) which is defined in RFC1592
section 3.1.
The Management Information Base(MIB) is defined by RFC 1155. The specific
MIB variables snmpmibd is managing are defined by the
following RFCs:
- RFC 1213
- MIB-II
- RFC 1229
- Extension to the Generic-Interface MIB
- RFC 1231
- IEEE 802.5 Token Ring MIB
- RFC 1398
- Ethernet-like Interface Types MIB
- RFC 1512
- FDDI MIB
Note
The "system" and "snmp" groups defined in RFC1213 are not implemented by snmpdmibd daemon. Instead they are implemented by snmpdv3 agent.
The snmpmibd daemon is normally executed during system
startup when /etc/rc.tcpip shell script is called.
The snmpmibd daemon should be controlled using the
System Resource Controller(SRC). Entering snmpmibd at
the command line is not recommended.
Use the following SRC commands to manipulate the snmpmibd daemon:
- startsrc
- Starts a subsystem, group of subsystems, or a subserver.
- stopsrc
- Stops a subsystem, group of subsystems, or a subserver.
- refresh
- Causes a subsystem or group of subsystems to reread the appropriate
configuration file.
- lssrc
- Gets the status of a subsystem, group of subsystems, or a subserver.
If the user issuing the long status form of the lssrc command
is not the root user, no community name information is displayed.
Flags
-c Community |
Use specified community name. If -c flag is not specified, the default
community name is public. |
-d [Level] |
Specifies tracing/debug level. The levels are:
- 8
- DPI level 1
- 16
- DPI level 2
- 32
- Internal level 1
- 64
- Internal level 2
- 128
- Internal level 3
Add the numbers for multiple trace levels.
If -d flag
is specified and the Level is not specified, the default
level is 56.
If -d flag is not specified, the
default level is 0. |
-f File |
A non-default configuration file. If the -f flag is
not specified, the default configuration file is /etc/snmpmibd.conf. See /etc/snmpmibd.conf file for information
on this file format. |
-h HostName |
Send request to specified host. If -h flag is
not specified, the default destination host is loopback (127.0.0.1). |
Examples
- To start the snmpmibd daemon, enter a command similar
to the following:
startsrc -s snmpmibd -a "-f /tmp/snmpmibd.conf"
This
command starts the snmpmibd daemon and reads the configuration
file from /tmp/snmpmibd.conf.
- To stop the snmpmibd daemon normally, enter:
lssrc -s hostmbid
This
command returns the name of the daemon, the process ID of the daemon, and
the state of the daemon (active or inactive).
- To get long status from the snmpmibd daemon, enter:
lssrc -ls snmpmibd
If you are the root user, this long form of the status
report lists the configuration parameters in /etc/snmpmibd.conf.
Files
/etc/snmpmibd.conf |
Defines the configuration parameters for snmpmibd command. |
/etc/mib.defs |
Defines the Management Information Base (MIB) variables
the SNMP agent and manager should recognize and handle. |
Related Information
The hostmibd command, snmpdv3 daemon.
[ Top of Page | Previous Page | Next Page | Contents | Index | Library Home |
Legal |
Search ]