IBM-DOS V-7.0 -R- ERROR Messages

 RAMDrive:Error in extended memory allocation 
    Cause:    RAMDRIVE.SYS.  The extended memory manager reported an error to RAMDRIVE.SYS while attempting to
              allocate memory for the RAM drive.
    Action:  Run memory diagnostic software on your system.  Consult the documentation for your extended memory
              manager.
 RAMDrive:Expanded Memory Manager not present 
    Cause:    RAMDRIVE.SYS.  You included the /a switch in the RAMDRIVE.SYS command line.  However, you failed to
              load the expanded memory manager before RAMDRIVE.SYS.  Therefore, RAMDRIVE.SYS could not be installed.
    Action:  You must always load RAMDRIVE.SYS after the expanded memory manager when the /a switch is used.
 RAMDrive:Expanded Memory Status shows error 
    Cause:    RAMDRIVE.SYS.  DOS detected an error in the expanded memory adapter while trying to install
              RAMDRIVE.SYS.  RAMDRIVE.SYS could not be installed.
    Action:  Consult your expanded memory adapter documentation for information about memory errors.
 RAMDrive:Extended Memory Manager not present 
    Cause:    RAMDRIVE.SYS.  RAMDRIVE.SYS could not find the extended memory manager.
    Action:  Install HIMEM.SYS or another XMS extended memory manager.  Make sure the device command that
              installs the extended memory manager comes before the device command for RAMDRIVE.SYS in the CONFIG.SYS
              file.
 RAMDrive:Insufficient memory 
    Cause:    RAMDRIVE.SYS.  There is not enough memory available to set up a RAM drive.  RAMDRIVE.SYS was not
              installed.
    Action:  Free some extended memory or obtain more memory.
 RAMDrive:Invalid parameter 
    Cause:    RAMDRIVE.SYS.  The parameters you specified in your CONFIG.SYS entry for RAMDRIVE.SYS are not
              correct.  RAMDRIVE.SYS was not installed.
    Action:  Check to see if you specified too many parameters, if one of your numeric parameters is not valid, if
              you specified conflicting switches, or if you specified too many switches.
 RAMDrive:I/O error accessing drive memory 
    Cause:    RAMDRIVE.SYS.  While setting up the RAMDRIVE.SYS driver, an error was detected in the memory being
              accessed for the RAM drive. RAMDRIVE.SYS was not installed.
    Action:  Run the memory test for the memory on which you were attempting to install the RAM drive.
 RAMDrive:No extended memory available 
    Cause:    RAMDRIVE.SYS.  Your computer has no memory available for RAM drives.  RAMDRIVE.SYS was not
              installed.
    Action:  Free some extended memory or obtain more memory.
 RATE and DELAY must be specified together 
    Cause:    MODE.  The typematic rate and delay must both be set at the same time.
    Action:  Specify both rate and delay values when you want to change the setting of either.
 Read fault error 
    Cause:    COMMANDS.  PC DOS was unable to read the data from the device.
    Action:  Make sure the device is installed and connected correctly, and that the medium is properly inserted in
              the drive.
  If you get the same message, select Abort and rerun the command with different medium.
 Requested configuration unavailable 
    Cause:    PCMCIA.  One or more of the configuration changes you tried to make to this card is not available.
    Action:  Make another selection or change the value and try again.
 Requested I/O unavailable 
    Cause:    PCMCIA.  The I/O setting you tried to assign to this card is not available, probably because it is being
              used by another device.
    Action:  Select another I/O setting or reallocate the I/O of the device that currently controls it.
 Requested IRQ unavailable 
    Cause:    PCMCIA.  The IRQ level you tried to assign this card is not available, probably because it is being used
              by another device or by the system.
    Action:  Select another IRQ or reallocate the IRQ of the device that currently controls it.
 Requested logical drive size exceeds the maximum available space. 
    Cause:    FDISK.  The cylinder size entered for the logical drive is larger than the maximum available space in the
              extended DOS partition.  FDISK displays the maximum available size for the partition as the default entry value.
    Action:  Enter a value that is less than or equal to the default size displayed.
 Requested Memory unavailable 
    Cause:    PCMCIA.  The memory range you tried to assign to this card is not available, probably because it is
              being used by another device.
    Action:  Select another range setting, accept the default, or reallocate the memory of the device that currently
              controls it.
 Requested partition size exceeds the maximum available space. 
    Cause:    FDISK.  The cylinder size entered for the partition size is larger than the maximum available space on
              the hard disk.  FDISK displays the maximum available size for the partition as the default entry value.
    Action:  Enter a value that is less than or equal to the default size displayed.
 Required font not loaded 
    Cause:    MODE.  The console device driver (DISPLAY.SYS) does not have the font size required to set the
              requested number of lines in the current code page.
    Action:  Set the maximum number of subfonts in the DEVICE=DISPLAY.SYS statement in the CONFIG.SYS file;
              restart PC DOS.
 Required parameter missing 
    Cause:    COMMANDS.  You tried to use a command without using a required parameter.
    Action:  To find out which parameters are valid, at the command prompt, type help followed by the command
              name.
 Restore file sequence error 
    Cause:    RESTORE.  The file was not restored because the diskettes were not inserted in sequential order.
    Action:  Retry the restore, inserting the diskettes in sequential order.


Back to  Jump to TOP-of-PAGE

Please see the LEGAL  -  Trademark notice.
Feel free - send a Email-NOTE  for any BUG on this page found - Thank you.