Appendix A. Messages

 A.0 Appendix A.  Messages 
     This appendix lists the messages that the LAN Support Program Custom
     Version 1.01 device driver files can display when being loaded into
     memory.  These messages start with DXM.
 A.1 Message Format 
     Figure A-1 shows the format of the sample message:
       DXMA0 02E: DOS Version 3.3 or later required.
     The messages are listed in numerical order.  See the sections following
     this table for descriptions of the device driver, message type, and
     message text categories.
     +------------------------------------------------------------------------+
     | Figure  A-1. Message Format                                            |
     +-----------+-----------+------------+-----------------------------------+
     | Device    | Message   | Message    |                                   |
     | Driver    | Number    | Type       | Message Text                      |
     +-----------+-----------+------------+-----------------------------------+
     | DXMA0     | 02        | E          | DOS Version 3.3 or later required |
     +-----------+-----------+------------+-----------------------------------+
 A.1.1 Device Driver Identifier 
     The first 5 characters of the message (for example, DXMT0) identify the
     device driver that originated the message.  These drivers are as follows:
         DXMA0MOD.SYS
         DXMC0MOD.SYS
         DXMT0MOD.SYS
     For a description of these drivers, see "Device Driver Summary" in
     topic 4.1.
 A.1.2 Message Type 
     The two types of messages are:
     E   Error
     I   Information.
 A.1.3 Message Text 
     The message text is a phrase describing the message.  The variable
     portions of the message are represented by symbols separated from the rest
     of the message text by single quotation marks.  The description of these
     symbols follows:
     °   The adapter number is represented by 'n'.  This number may be 0 or 1
         (0 for the primary adapter, 1 for the alternate adapter).  The LAN
         Support Program Custom supports only one adapter, but that adapter can
         be configured as either primary or alternate.
     °   The term 'data' stands for 24 bytes of the DEVICE= line in the
         CONFIG.SYS file.  The bytes begin with the abbreviation of the NETBIOS
         keyword in error, followed by the "=" and the value of the parameter.
         For example, consider the following message:
           DXMT0 36E: Invalid keyword value:  SS=18
         The 'data' in this example is SS=18.  The following command is entered
         in CONFIG.SYS:
           DEVICE=DXMT0MOD.SYS SS=18
         SS is the incorrect keyword; you must replace it with a correct
         keyword abbreviation, such as S.  (Refer to "Keyword Values for the
         NETBIOS New Parameters" in topic 4.4.2 for a description of the
         keywords.)
     The terms Token-Ring Adapter and Token-Ring Network Adapter refer to the
     adapter with which the LAN Support Program Custom is shipped.
     If an error message is displayed, you will be prompted by the device
     driver to "Press F1 to Continue." After pressing F1, wait for the DOS
     prompt to be displayed.  When it is, you can attempt to correct the
     problem by reading the "Explanation" and following the directions provided
     as "User Response."
     Information relating to parameters can be found in Chapter 4, "Customizing
     the Device Driver Parameters."
 A.2 Device Driver Message Listings 
     The LAN Support Program Custom Version 1.01 can display the messages
     listed in this section.  Each message number is preceded by the identifier
     of the device driver.  This identifier (for example, DXMT0) is not shown
     in the listing because it varies depending upon which driver displays the
     message.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 00I:   Please wait, opening adapter 'n'                                |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  The Token-Ring Network Adapter is executing an open process.
     User Response:  This is an information message; no action is required.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 02E:   DOS Version 3.3 or later required                               |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  The DOS version is earlier than 3.3.
     User Response:  The DOS version needs to be changed to Version 3.3 or
     later.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 04E:   Program already loaded                                          |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  This device driver was already installed into memory.
     User Response:  Do one of the following:
     °   Use the Installation Aid to reconfigure.
     °   Check the CONFIG.SYS file to ensure that the device driver is not
         listed twice.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 05E:   Invalid node address parameter                                  |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  The address parameter is invalid, an invalid global
     parameter was entered, or a comma was placed after a global parameter.  (A
     global parameter is a non-positional parameter.  See "Global and
     Positional Parameters" in topic 4.3.3.)
     User Response:  Do one of the following:
     °   Use the Installation Aid to reconfigure the parameter.
     °   Edit the CONFIG.SYS file to correct the address parameter or the
         global parameter for this device driver.  See Chapter 4, "Customizing
         the Device Driver Parameters" for more information about configuring
         the parameters.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 06E:   Error reading message file (DXM.MSG)                            |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  The message file, DXM.MSG, is not present or could not be
     read for one or more of the following reasons:
     °   The Interrupt Arbitrator (DXMA0MOD.SYS) was not previously loaded.
     °   DXM.MSG could not be located.
     °   The language type of the file does not correspond to the DOS language
         type specified by the DXMA0MOD.SYS language parameter.
     °   DXM.MSG is from the wrong version of the LAN Support Program Custom.
     NOTE:  This message is not translated.  U.S. English is always displayed.
     User Response:
     °   Make sure that the Interrupt Arbitrator is loaded.  Do this in one of
         two ways:
         -   Use the Installation Aid to reconfigure.
         -   Edit the CONFIG.SYS file to ensure that the DXMA0MOD.SYS device
             driver is listed in the correct sequence.  DXMA0MOD.SYS must be
             loaded before any other LAN Support Program Custom device driver.
     °   Make sure that DXM.MSG is present on the working copy in the same
         directory as the LAN Support Program Custom device drivers.
     °   If you did not use the Installation Aid, and you are not using U.S.
         English, be sure that you renamed DXMMSG.ccc to DXM.MSG on the working
         copy (ccc represents the DOS country code).
     °   Make sure that the language type of the file matches the language type
         specified by the DXMA0MOD.SYS parameter.  See "Copying DXM.MSG" in
         topic 3.2.1.
     °   Make sure that you got the message file and the LAN Support Program
         Custom device drivers from the same version of the LAN Support Program
         Custom.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 10E:   Invalid shared RAM address                                      |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  The shared RAM address is invalid.
     User Response:  Perform one of the following actions:
     °    Refer to the installation and testing instructions for the adapter
         for instructions about setting or checking shared RAM page size.  Make
         sure that the shared RAM is on the correct boundary.  See "Shared RAM"
         in topic 4.3.7 for more information.
     °   Use the Installation Aid to reconfigure the parameter.
     °   Edit the CONFIG.SYS file to correct the shared RAM parameter.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 11E:   DIR.INITIALIZE failed                                           |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  The Token-Ring Network Adapter failed to initialize.
     User Response:  Refer to the section describing the adapter diagnostics in
     the adapter installation and testing instructions.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 12E:   Token-Ring Adapter not installed                                |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  The Token-Ring Network Adapter was not detected.
     User Response:   Be sure that the adapter is installed in your computer.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 13I:   Token-Ring Network Adapter data rate =  4 Mbps                  |
     |                                                                        |
     | 13I:   Token-Ring Network Adapter data rate = 16 Mbps                  |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  Token-Ring Network Adapter data rate.
     User Response:  This is an information message:  no action is required.
     NOTE:  Only one of these messages appears.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 14E:   Invalid Early Token Release parameter                           |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  The parameter is not correct.
     User Response:  Do one of the following:
     °   Use the Installation Aid to reconfigure the parameter.
     °   Edit the CONFIG.SYS file to correct the Early Token Release parameter.
         For a description of the Early Token Release parameter, see "Early
         Token Release" in topic 4.3.8.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 16E:   Invalid minimum SAP parameter                                   |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  The parameter value is out of range.
     User Response:  Do one of the following:
     °   Use the Installation Aid to reconfigure the parameter.
     °   Edit the CONFIG.SYS file to correct the parameter.  For a description
         of the minimum SAP parameter, see "MINSAP" in topic 4.3.9.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 17E:   Invalid minimum link station parameter                          |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  The parameter value is out of range.
     User Response:
     °   Use the Installation Aid to reconfigure the parameter.
     °   Edit the CONFIG.SYS file to correct the parameter.  For a description
         of the minimum link station parameter, see "MINLINK" in topic 4.3.10.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 31E:   Requested resources exceed capabilities on adapter 'n'          |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  The resources defined exceed those supported by the LAN
     Support Program Custom or by the adapter; for example, too many link
     stations are defined.  This error message can appear when the device
     driver parameters EXTRA.SAPS, EXTRA.STATIONS, STATIONS, MINSAP, or MINLINK
     are set so that the work area available with LAN Support Program Custom
     Version 1.01 is exhausted.
     User Response:  Do one of the following:
     °   Use the Installation Aid to reconfigure the parameters to ensure that
         the resource requirements are not exceeded.  You may need to reduce
         the values of the parameters EXTRA.SAPS, EXTRA.STATIONS, STATIONS,
         MINSAP, or MINLINK.
     °   Edit the CONFIG.SYS file to ensure that the resource requirements are
         not exceeded.  You may need to reduce the values of the parameters
         EXTRA.SAPS, EXTRA.STATIONS, STATIONS, MINSAP, or MINLINK.
     See "Work Area Considerations for LAN Support Program Custom Version 1.01"
     in topic 4.7 for more information.  If you must have higher values for
     these parameters than the LAN Support Program Custom Version 1.01
     supports, you must obtain one of the stand-alone versions of the LAN
     Support Program.  See "Using a Stand-Alone Version of the LAN Support
     Program" in topic 1.1.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 32E:   Initialization or open error on adapter 'n'                     |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  There was an adapter failure or the adapter was already
     open.
     User Response:  If the NETBIOS OPEN.ON.LOAD parameter is set, then the
     NETBIOS driver DXMT0MOD.SYS will try to open the adapter at load time.
     See "Keyword Values for the NETBIOS New Parameters" in topic 4.4.2 for
     instructions about the parameter.  If an initialization or open error
     occurs, this message appears.  Check the adapter data rate and adapter
     diagnostic information as follows:
     °   Verify that the adapter data rate is the same as the ring data rate.
         Your LAN administrator will know the ring data rate.  If the rates are
         different, refer to the adapter installation and testing instructions
         for instructions about changing the rate.
     °   Refer to the adapter installation and testing instructions for
         diagnostic information.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 33E:   Cannot mix OLD.PARMS.x and 'new' keywords                       |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  Both new and old NETBIOS (DXMT0MOD.SYS) parameters are mixed
     on the device driver parameter line.
     User Response:  Do one of the following:
     °   Use the Installation Aid to reconfigure the parameters for NETBIOS
         (DXMT0MOD.SYS).
     °   Edit the CONFIG.SYS file to ensure that the parameter types are not
         mixed.  See "The NETBIOS Old Parameters" in topic 4.4.1 and "Keyword
         Values for the NETBIOS New Parameters" in topic 4.4.2 for more
         information about the keywords.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 34E:   Invalid keyword: 'data'                                         |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  The keyword used is invalid.
     User Response:  Do one of the following:
     °   Use the Installation Aid to reconfigure the parameters for NETBIOS
         (DXMT0MOD.SYS).
     °   Edit the CONFIG.SYS file to ensure that the keyword is correct.  See
         "The NETBIOS Old Parameters" in topic 4.4.1 and "Keyword Values for
         the NETBIOS New Parameters" in topic 4.4.2 for more information about
         the keywords.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 35E:   Duplicate keyword: 'data'                                       |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  This keyword is used twice on the device driver parameter
     line.
     User Response:  Do one of the following:
     °   Use the Installation Aid to reconfigure the parameters for NETBIOS
         (DXMT0MOD.SYS).
     °   Edit the CONFIG.SYS file to remove the keyword listed twice.  See "The
         NETBIOS Old Parameters" in topic 4.4.1 and "Keyword Values for the
         NETBIOS New Parameters" in topic 4.4.2 for more information about the
         keywords.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 36E:   Invalid keyword value: 'data'                                   |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  The value listed is invalid for its keyword.
     User Response:  Do one of the following:
     °   Use the Installation Aid to reconfigure the parameters for NETBIOS
         (DXMT0MOD.SYS).
     °   Edit the CONFIG.SYS file to ensure that the value is correct.  See
         "The NETBIOS Old Parameters" in topic 4.4.1 and "Keyword Values for
         the NETBIOS New Parameters" in topic 4.4.2 for more information about
         the keywords.
     +------------------------------------------------------------------------+
     |                                                                        |
     | 37E:   Adapter support required                                        |
     |                                                                        |
     +------------------------------------------------------------------------+
     Explanation:  No adapter support has been loaded.
     User Response:  Do one of the following:
     °   Use the Installation Aid to reconfigure.
     °   Edit the CONFIG.SYS file to ensure that the IEEE 802.2 driver,
         DXMC0MOD.SYS, is listed.


Back to  Jump to TOP-of-PAGE

Please see the LEGAL  -  Trademark notice.
Feel free - send a Email-NOTE  for any BUG on this page found - Thank you.