Manual Installation of the LAN Support Program Custom Version 1.01

 3.0 Chapter 3.  Manual Installation of the LAN Support Program Custom Version 1.01 
     The Installation Aid enables you to do a complete configuration,
     including changing all the LAN Support Program Custom device driver
     parameters.  However, if you prefer to do a manual configuration, the
     steps required to install the program are as follows:
     1.  Prepare your computer.
     2.  Copy the LAN Support Program Custom files to your working copy. (1)
     3.  Edit CONFIG.SYS to load the device drivers.
     4.  Change the device driver parameters, if required.
     5.  Restart the computer to load the working copy.
      (1) A working copy is a copy of the program that has been
         configured for use in a particular computer.  The working
         copy can be installed on a diskette or on a fixed disk.
 3.1 Preparing the Computer 
     Follow these steps to prepare the computer:
     1.  If you will be starting the computer from a fixed disk, make sure that
         DOS 3.3 or higher has been installed on the fixed disk.  Use the DOS
         VER command to check the DOS level.  If you must reformat your fixed
         disk, be sure to back up your files.  See the IBM Personal Computer
         Disk Operating System User's Guide for your version of DOS for
         instructions.
     2.  If you will be starting the computer from a diskette (instead of a
         fixed disk), be sure that you have a formatted diskette for use as the
         working copy.  It must be formatted as a DOS 3.3 or higher system
         diskette.  Use the DOS FORMAT command with the /S option to format it,
         if it is not already formatted.
 3.2 Copying the Files 
     The program files for the LAN Support Program Custom are found in the
     root directory of the LAN Support Program Custom Program Diskette, which
     is supplied with the adapter.  You should make a backup copy of the LAN
     Support Program Custom Program Diskette and use the backup copy as the
     source diskette.  See "Making a Backup Copy" in topic 2.2.2.
     To create your working copy, set up a directory on the disk or diskette
     you plan to use for the working copy.  Copy these files to that directory:
     °   DXMA0MOD.SYS
     °   DXMC0MOD.SYS.
     The driver named DXMT0MOD.SYS provides the NETBIOS interface.  If you need
     the NETBIOS interface, copy this file as well.
 3.2.1 Copying DXM.MSG 
     If you are using U.S. English, copy the file DXM.MSG that is provided with
     the LAN Support Program Custom.  The version of DXM.MSG that is provided
     with the program contains the LAN Support Program Custom device driver
     messages in U.S. English.
     If you are using a different language, you cannot use the DXM.MSG file
     that is provided.  To get the DXM.MSG file in the language you need, you
     must copy DXMMSG.ccc under the name DXM.MSG. The letters ccc represent a
     number that corresponds to one of the values used by the DOS COUNTRY
     command that is defined in the IBM Personal Computer Disk Operating System
     User's Guide for your version of DOS.  LAN Support Program Custom Version
     1.01 supports only Spanish, German, and Japanese.  See "Parameter for the
     Interrupt Arbitrator Device Driver (DXMA0MOD.SYS)" in topic 4.2 for a list
     of the country codes for these languages.
     To copy the message file, first select the supported value of ccc that
     corresponds to the language you are using in DOS.  For example, DXMMSG.034
     is the message file for Spanish.  Copy the desired file to the working
     copy with the new name DXM.MSG.
     NOTE:  The correct message file must be copied and renamed DXM.MSG, or the
     LAN Support Program Custom cannot be activated.
 3.3 Editing CONFIG.SYS 
     In the following example, \LSP represents the directory in which the
     working copy of the LAN Support Program Custom is located.  You may
     substitute another directory if you like.
     Edit CONFIG.SYS to include the following lines:
       DEVICE=\LSP\DXMA0MOD.SYS
       DEVICE=\LSP\DXMC0MOD.SYS
     If you plan to use the NETBIOS interface, also include the statement:
       DEVICE=\LSP\DXMT0MOD.SYS
     These statements may be entered anywhere in CONFIG.SYS but must be listed
     in the order shown (DXMA0MOD.SYS first, then DXMC0MOD.SYS, and, last,
     DXMT0MOD.SYS).
     DXMA0MOD.SYS is the interrupt arbitrator for all the device driver files.
     It has a language parameter (ccc) that defines the language in which
     load-time messages are displayed.  If this parameter is equal to 001, all
     load-time messages are displayed in U.S. English.
     If you are using a different language, this parameter must be the same as
     the ccc file extension that identified the DXMMSG.ccc file you copied.
     For example, if you specified the DXMA0MOD.SYS language parameter as 034
     (for Spanish), you should copy the DXMMSG.034 message file and rename it
     DXM.MSG.  See "Parameter for the Interrupt Arbitrator Device Driver
     (DXMA0MOD.SYS)" in topic 4.2 for a syntax diagram showing you how to enter
     this parameter.
     NOTE:  The statements in CONFIG.SYS are different if you use a memory
     manager.  See Chapter 5, "Using DOS 5.0, Windows, and QEMM-386" for more
     information.
 3.3.1 Changing Parameters 
     The default values for the device driver parameters are usually
     acceptable.  If you need to alter some parameters, you can edit the
     DEVICE= statements as described in Chapter 4, "Customizing the Device
     Driver Parameters."
 3.3.2 Tips for Editing CONFIG.SYS 
     Use the following tips to edit CONFIG.SYS:
     °   The DEVICE= line needs to include the path DEVICE=\LSP\DXM...  where
         \LSP represents the directory.  You can substitute another directory
         name in place of \LSP.
     °   Each DEVICE= line must not exceed one line in the CONFIG.SYS file.
     °   If the working copy already has a CONFIG.SYS file, be sure to change
         only the lines needed for the LAN Support Program Custom device
         drivers.  For maximum safety, copy the original CONFIG.SYS file to a
         file with a unique extension to save it before editing.
 3.4 Loading the Working Copy 
     When you have completed the configuration of the working copy, load the
     LAN Support Program Custom as follows:
     °   If the LAN Support Program Custom configuration was copied to a fixed
         disk, remove any diskettes from the diskette drives and press the
         Ctrl-Alt-Del keys to restart the computer.
     °   If the LAN Support Program Custom was copied to a diskette, insert
         that diskette into the startup diskette drive (usually drive A:) and
         press the Ctrl-Alt-Del keys to restart the computer.
     A copyright statement will be displayed.  Look for messages.  If there are
     no messages or if there are only information messages, the LAN Support
     Program Custom is correctly loaded.  If any error messages are displayed,
     the LAN Support Program Custom may not be correctly installed; see
     Appendix A, "Messages." For additional help, see Chapter 6,
     "Recommendations and Problem Solving."  If no LAN Support Program Custom
     copyright statement is displayed, the LAN Support Program Custom is not
     installed or has been removed.  In this case, make a new backup copy and
     reinstall the program.


Back to  Jump to TOP-of-PAGE

Please see the LEGAL  -  Trademark notice.
Feel free - send a Email-NOTE  for any BUG on this page found - Thank you.