![]() |
|
This page deals with the options concerning:
|
|
Grid |
|
![]() |
|
Defines the grid options:DisplayDefines whether the grid is displayed.
Snap to pointDefines whether annotations are snapped to the grid point.
Allow DistortionsDefines whether grid spacing and graduations are the same horizontally and vertically.
H Primary spacingDefines the grid horizontal spacing.
H GraduationsDefines the grid horizontal graduations.
V Primary spacingDefines the grid vertical spacing, available only if Allow Distortions is selected.
V GraduationsDefines the grid vertical graduations, available only if Allow Distortions is selected.
|
|
Sketch Plane |
![]() |
![]() |
|
Defines the sketch plane options:Shade sketch planeDefines whether a shaded plane is displayed in the Sketcher workbench representing the sketch plane.
Position sketch plane parallel to screenDefines if the sketch plane is positioned parallel to the screen when you enter in the Sketcher workbench, otherwise the default orientation is kept.
Visualization of the cursor coordinatesDefines whether the cursor coordinates are displayed, near the cursor, within the geometry.
|
|
Geometry |
![]() |
![]() |
|
Defines the geometry options:Create circle and ellipse centersDefines when you create a circle or an ellipse whether its center is created.
Allow direct manipulationDefines whether you are able to move geometry using the mouse according to the Solving Mode options.
Solving Mode...Click this button to display the solving mode options. |
|
![]() |
|
Solving mode for moving elements
Drag elements end points includedDefines whether you move geometrical elements with their end points.
|
|
Constraint |
![]() |
![]() |
|
Defines the constraint options:Creates the geometrical constraintsDefines whether the geometrical constraints detected by the SmartPick
tool are created. This option is also available in the Sketcher Tools
toolbar through the Geometrical Constraints capability
Creates the dimensional constraintsDefines whether the dimensional constraints detected by the SmartPick
tool are created. For more information, see
SmartPick. This option is also available in the Sketcher Tools
toolbar thru the Dimensional Constraints capability
SmartPick...Click this button to display the SmartPick options. The SmartPick detects multiple directions and positions, and more and more relationships with existing elements. This may lead to confusion due to the rapid highlighting of several different detection possibilities as you point the cursor at different elements in rapid succession. |
|
![]() |
|
Support lines and circlesDefines whether the line and arc of circle support are detected. AlignmentDefines whether alignment constraint is detected. ParallelismDefines whether parallelism constraint is detected. PerpendicularityDefines whether perpendicularity constraint is detected. TangencyDefines whether tangency constraint is detected. Horizontal and verticalDefines whether horizontal and vertical constraints are detected.
|
|
Colors |
![]() |
![]() |
|
Defines the colors options:Default color of the elementsDefines the color of the geometrical elements.
Visualization of diagnosisDefines whether the diagnosis colors are applied. See Colors diagnoses.
Colors...Click this button to display diagnosis colors options. |
|
![]() |
|
Over-constrained elementsDefines the color of over-constrained elements.
Inconsistent elementsDefines the color of inconsistent elements.
Not-changed elementsDefines the color of unchanged elements.
Iso-constrained elementsDefines the color of iso-constrained elements.
Other color of the elementsDefines the color of the elements which are different of geometrical and diagnosis elements. See Colors for other elements. Colors...Click this button to display colors for other elements options. |
|
![]() |
|
Protected elementsDefines the color of the protected elements.
Construction elementsDefines the color of construction elements.
SmartPickDefines the color of the SmartPick assistant elements and symbols.
|
|
Update |
![]() |
![]() |
|
Select this option to ensure that the
Update Diagnosis dialog box appears to inform you that the sketch you
have modified is under-constrained.
|