101-000 A Description: The system hung while attempting to configure a device. Action: Use MAP 1540. 101-185 A Description: A checkstop occurred. Action: Use MAP 1540 in the system unit service guide to isolate the cause. 101-517 A Description: The system unit failed to IPL. Action: Use MAP 1540. Description: CD-ROM read problems after 101-518 A boot. Note:The boot record was read from the CD-ROM disk. However, errors occurred when trying to mount the CD-ROM file system. This problem can be caused by SCSI device addressing, SCSI terminator, open PTC, SCSI cable, etc. Action: Go to Chapter 7. "MAP 0050: SCSI Problems Isolation Procedure" Description: The configuration manager 101-521 A detected an error. to Action: If you are running the diagnostics 101-538 from a disk, try running the diagnostics from a CD-ROM. If the diagnostics run correctly from CD-ROM, the problem may be damaged data on the disk. Contact your software support facility. If a different problem occurs when you run the diagnostics from CD ROM, correct that problem. If you were running from a CD ROM at first, or have the same problem on CD ROM that you had when running diagnostics from disk then go to MAP 1540, in either the service guide or the installation and service guide for this system unit. Description: Disk read problems occurred 101-544 A after booting. errors occurred when trying to open the disk drive. This problem can be caused by SCSI device addressing, SCSI terminator, open PTC, SCSI cable, etc. Action: Go to Chapter 7. "MAP 0050: SCSI Problems Isolation Procedure" Description: The system hung while 101-551 A loading the software. This can be caused by to a hardware or software problem. 101-557 Action: Run the diagnostics from CD-ROM. Start at Chapter 4. "MAP 0020: Problem Determination Procedure", Step 14. If the diagnostics run correctly from CD-ROM, the problem may be damaged disk data. Consider having the customer contact Software Support before reinstalling the operating system on the disk. If you still get the same SRN, go to MAP 1540 in either the service guide or the installation and service guide for this system unit. Description: There is not enough memory 101-558 A to execute diagnostics. Action: There must be a minimum of 16MB of installed memory. If the system has 16MB or more of memory installed, suspect a problem with a memory card. 101-559 A Description: The system halted while software was loading. This problem may be to attributed to either hardware or software. Action: Use the CD ROM based diagnostics if 101-599 not yet used. If the same SRN is generated from the CD ROM diagnostics, go to MAP 1540 in the system unit service guide for problem isolation. If the SRN is not generated when using the CD ROM, suspect a problem with the system's software. A xxx Description: The system hung while trying 101-711 to configure an unknown resource. to Action: Run diagnostics from CD-ROM. Start 101-726 at Chapter 4. "MAP 0020: Problem Determination Procedure", Step 14. If you still get the same SRN, refer to "Failing Function Code List" and find the FFC that matches the last three digits of the SRN. Suspect the device adapter or device itself. If more than one adapter or device is installed, isolate the failing resource by removing the adapters or devices one at a time and checking if the system stops with the same value in the three-digit display. Note: xxx corresponds to the last three digits of the SRN. The system hung while trying 101-727 A to configure an asynchronous adapter. Use MAP 1540 in the installation and service guide for this system unit. Suspect a problem with one of the async adapters. 101-7C1 A 7C1 Description: The system unit halted while configuring an audio subsystem. 101-888 A 210 Description: The system does not IPL. Action: Use Chapter 16. "MAP 0260: System 227 Hangs During Resource Configuration". E10 101-c32 D The system hung while indicating that a direct-attached display was selected as the console. Go to MAP 1540 in either the service guide or the installation and service guide for this system unit. Suspect the graphics adapter being used for the display console first. 101-c33 D Description: The system hung while indicating that a TTY terminal is the system console. Action: Go to MAP 1540 in either the service guide or the installation and service guide for this system unit. Suspect the graphics adapter being used for the display console first. 101-xxx A xxx Description: The system hung while configuring a resource. The last three 227 digits identify the failing function code for the resource being configured. Action: Use Chapter 16. "MAP 0260: System Hangs During Resource Configuration". 103-151 D 151 Description: The time-of-day battery failed. 103-202 H Description: Unexpected interrupt. to Action: Go to MAP 1540 in either the 103-210 service guide or the installation and service guide for this system unit. 109-200 B Description: The system crashed while being run by the customer. Action: Use Chapter 4. "MAP 0020: Problem Determination Procedure", and get a new SRN. 110-101 C Description: The diagnostics did not detect an installed resource. Action: If this SRN appeared when running concurrent diagnostics, then run concurrent using the diag -a command, otherwise use Chapter 18. "MAP 0290: Missing Resource Problem Resolution". 110-908 D 908 Description: The system halted while diagnostics were executing. C33 C36 110-921 D Description: The system halted while to xxx diagnostics were executing. 110-926 812 Note: xxx corresponds to the last three digits of the SRN. 110-935 D 935 Description: The system halted while diagnostics were executing. 812 110-946 D 946 Description: The system halted while diagnostics were executing. 221 110-xxx D Description: The system halted while xxx diagnostics were executing. 221 Note: xxx corresponds to the last three digits of the SRN. If your 110 SRN is not listed below, use the 110-xxx procedure. 111-259 B Description: Cannot display readable information on the terminal. Action: Use Chapter 17. "MAP 0280: Boot Problem Resolution" Entry 3. 111-725 B 725 Description: Cannot display readable information on the display. Note: Suspect the display adapter attached to the console display. Action: Use Chapter 17. "MAP 0280: Boot Problem Resolution" 111-736 B 736 Description: The keyboard does not respond. 821 Action: Use Chapter 17. "MAP 0280: Boot Problem Resolution" Entry 1. 111-78C B PCI adapter Description: I/O bus problem. Action: Use Chapter 12. "MAP 0210: General 227 Problem Resolution". E10 Note: PCI adapter refers to the adapters you made note of when using Chapter 11. "MAP 0080 System Bus Problem Isolation". 111-82C B Description: Cannot display readable information on the display. Action: Go to Chapter 17. "MAP 0280: Boot Problem Resolution" Entry 2. 111-922 B 922 Description: The keyboard does not respond. 821 Action: Use Chapter 17. "MAP 0280: Boot Problem Resolution" Entry 1. 111-923 B 923 Description: The keyboard does not respond. 821 Action: Use Chapter 17. "MAP 0280: Boot Problem Resolution" Entry 1. 111-947 B 221 Description: System beeper not functioning correctly. 111-999 D 210 Description: System does not perform a soft reset. 2E6-212 D 2E6 Description: FIFO empty bit set. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E6-213 D 2E6 Description: FIFO empty bit clear. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E6-214 D 2E6 Description: FIFO full bit set. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E6-215 D 2E6 Description: FIFO full bit clear. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E6-216 D 2E6 Description: FIFO data miscompare. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E6-217 D 2E6 Description: SCSI FIFO data miscompare. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E6-218 D 2E6 Description: SCSI FIFO underflow. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E6-219 D 2E6 Description: SCSI parity error. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E6-220 D 2E6 Description: SCSI FIFO flags error. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E6-221 D 2E6 Description: Miscompare during the write/read of the configuration register. 221 Action: Go to Chapter 7. "MAP 0050: SCSI Problems Isolation Procedure". 2E6-222 D 2E6 Description: Error during the write/read of the memory register. 221 Action: Go to Chapter 7. "MAP 0050: SCSI Problems Isolation Procedure". 2E6-223 D 2E6 Description: Miscompare during the write/read of the memory I/O register. 221 Action: Go to Chapter 7. "MAP 0050: SCSI Problems Isolation Procedure". 2E6-224 D 2E6 Description: Error reading the PCI configuration register. 221 2E6-225 D 2E6 Description: Adapter POST failed. 221 2E6-230 D D50 Description: Arbitration test failed. Action: Go to Chapter 7. "MAP 0050: SCSI 2E6 Problems Isolation Procedure". 2E6-231 D D50 Description: Function could not complete. Action: Go to Chapter 7. "MAP 0050: SCSI 2E6 Problems Isolation Procedure". 2E6-232 D D50 Description: SCSI bus data miscompare. Action: Go to Chapter 7. "MAP 0050: SCSI 2E6 Problems Isolation Procedure". 2E6-240 D 2E6 Description: No terminal power. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E6-301 D 2E6 Description: Configuration open failed for parent bus. D50 software 2E6-700 G 2E6 Description: Error log analysis indicates a PCI SCSI adapter failure. software 2E6-701 G 2E6 Description: Error log analysis indicates a PCI SCSI adapter failure. software 2E6-702 G 2E6 Description: Error log analysis indicates a PCI SCSI adapter failure. software 2E6-703 G 2E6 Description: Error log analysis indicates a PCI SCSI adapter failure. software 2E6-704 G 2E6 Description: Error log analysis indicates a PCI SCSI adapter failure. software 2E6-705 G 2E6 Description: Error log analysis indicates a PCI SCSI adapter failure. software 2E6-800 G 2E6 Description: Error log analysis indicates a PCI SCSI adapter PTC failure. Action: Go to Chapter 7. "MAP 0050: SCSI Problems Isolation Procedure". 2E6-802 G 2E6 Description: Error log analysis indicates a PCI SCSI bus failure. Action: Go to Chapter 7. "MAP 0050: SCSI Problems Isolation Procedure". 2E7-212 D 2E7 Description: FIFO empty bit set. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E7-213 D 2E7 Description: FIFO empty bit clear. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E7-214 D 2E7 Description: FIFO full bit set. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E7-215 D 2E7 Description: FIFO full bit clear. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E7-216 D 2E7 Description: FIFO data miscompare. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E7-217 D 2E7 Description: SCSI FIFO data miscompare. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E7-218 D 2E7 Description: SCSI FIFO underflow. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E7-219 D 2E7 Description: SCSI parity error. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E7-220 D 2E7 Description: SCSI FIFO flags error. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E7-221 D 2E7 Description: Miscompare during the write/read of the configuration register. 221 Action: Go to Chapter 7. "MAP 0050: SCSI Problems Isolation Procedure". 2E7-222 D 2E7 Description: Error during the write/read of the memory register. 221 Action: Go to Chapter 7. "MAP 0050: SCSI Problems Isolation Procedure". 2E7-223 D 2E7 Description: Miscompare during the write/read of the memory I/O register. 221 Action: Go to Chapter 7. "MAP 0050: SCSI Problems Isolation Procedure". 2E7-224 D 2E7 Description: Error reading the PCI configuration register. 221 2E7-225 D 2E7 Description: Adapter POST failed. 221 2E7-230 D D50 Description: Arbitration test failed. Action: Go to Chapter 7. "MAP 0050: SCSI 2E7 Problems Isolation Procedure". 2E7-231 D D50 Description: Function could not complete. Action: Go to Chapter 7. "MAP 0050: SCSI 2E7 Problems Isolation Procedure". 2E7-232 D D50 Description: SCSI bus data miscompare. Action: Go to Chapter 7. "MAP 0050: SCSI 2E7 Problems Isolation Procedure". 2E7-240 D 2E7 Description: No terminal power. Action: Go to Chapter 7. "MAP 0050: SCSI 221 Problems Isolation Procedure". 2E7-301 D 2E7 Description: Configuration open failed for parent bus. D50 software 2E7-700 G 2E7 Description: Error log analysis indicates a PCI SCSI adapter failure. software 2E7-701 G 2E7 Description: Error log analysis indicates a PCI SCSI adapter failure. software 2E7-702 G 2E7 Description: Error log analysis indicates a PCI SCSI adapter failure. software 2E7-703 G 2E7 Description: Error log analysis indicates a PCI SCSI adapter failure. software 2E7-704 G 2E7 Description: Error log analysis indicates a PCI SCSI adapter failure. software 2E7-705 G 2E7 Description: Error log analysis indicates a PCI SCSI adapter failure. software 2E7-800 G 2E7 Description: Error log analysis indicates a PCI SCSI adapter PTC failure. Action: Go to Chapter 7. "MAP 0050: SCSI Problems Isolation Procedure". 2E7-802 G 2E7 Description: Error log analysis indicates a PCI SCSI bus failure. Action: Go to Chapter 7. "MAP 0050: SCSI Problems Isolation Procedure". 2EF-101 E 751 Description: Post indicates an adapter failure. 650-xxx D 650 Description: Disk drive configuration failed. 651-140 D 165 Description: Operator panel display test failed 221 651-150 D 166 Description: Sensor indicates a fan has failed. 2E0 Action: Use Chapter 13. "MAP 0220 Hot Plug FRU Problem Resolution". 651-151 D 152 Description: Sensor indicates a voltage is outside the normal range. 2E2 Action: Use MAP 1520. 651-152 D 2E1 Description: Sensor indicates an abnormally high internal temperature. Action: Verify that: 1. The room ambient temperature is within the system operating environment. 2. There is unrestricted air flow around the system. 3. All system covers are closed. 4. There are no fan failures. If none of these problems exist, then proceed with Chapter 13. "MAP 0220 Hot Plug FRU Problem Resolution". 651-153 D 152 Description: Sensor indicates a power supply has failed. E19 Action: Use Chapter 13. "MAP 0220 Hot Plug FRU Problem Resolution". 651-159 D Description: Sensor indicates a FRU has failed. Action: Use the physical location code(s) to replace the FRU(s) that are identified on the diagnostics problem report screen. 651-160 D 166 Description: Sensor indicates a fan is turning too slowly. 2E0 Action: Use Chapter 13. "MAP 0220 Hot Plug FRU Problem Resolution". 651-161 D 152 Description: Sensor indicates a voltage is outside the normal range. 2E2 Action: Use MAP 1520. 651-162 D 2E1 Description: Sensor indicates an abnormally high internal temperature. Action: Verify that: 1. The room ambient temperature is within the system operating environment. 2. There is unrestricted air flow around the system. 3. All system covers are closed. 4. There are no fan failures. If none of these problems exist, then proceed with Chapter 13. "MAP 0220 Hot Plug FRU Problem Resolution". 651-163 D 152 Description: Sensor indicates a power supply has failed. E19 Action: Use Chapter 13. "MAP 0220 Hot Plug FRU Problem Resolution". 651-169 D Description: Sensor indicates a FRU has failed Action: Use the physical location codes to replace the FRUs that are identified on the diagnostics problem report screen. 651-170 D Description: Sensor status not available. Action: Contact your support person. 651-171 D Description: Sensor status not available Action: Contact your support person. 651-600 G Description: Uncorrectable memory or unsupported memory. Action: Examine the memory modules and determine if they are supported types. If the modules are supported, then replace the appropriate memory module(s). 651-601 G Description: Missing or bad memory Action: If the installed memory matches the reported memory size, then replace the memory: otherwise, add the missing memory. 651-602 G 2C5 Description: Bad or missing memory Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-603 G 2C6 Description: Bad or missing memory Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-608 G D01 Description: Bad L2 Cache 651-609 G D01 Description: Missing L2 Cache 651-610 G 210 Description: CPU internal error 651-611 G 210 Description: CPU internal cache error 651-612 G D01 Description: L2 Cache parity or multi-bit ECC error 651-613 G D01 Description: L2 cache ECC single-bit error 651-614 G 214 Description: Time-out error waiting for memory controller 651-615 G 292 Description: Time-out error waiting for I/O 651-619 G Description: Error log analysis indicates an error detected by the CPU. The error log indicates the following physical FRU location(s) as the probable cause(s). Action: Use the physical location codes to replace the FRUs that are identified on the diagnostics problem report screen. 651-620 G 2C5 Description: ECC correctable error Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-621 G 2C6 Description: ECC correctable error Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-622 G 2C5 Description: Correctable error threshold exceeded Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-623 G 2C6 Description: Correctable error threshold exceeded Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-624 G 214 Description: Memory controller internal error 651-625 G 214 Description: Memory Address (Bad address going to memory) 651-626 G 214 Description: Memory Data error (Bad data going to memory) 651-627 G 214 Description: Memory time-out error 651-628 G 210 Description: Processor time-out error 651-629 G Description: Error log analysis indicates and error detected by the memory controller. The error log indicates the following physical FRU location(s) as the probable cause(s). Action: Use the physical location codes to replace the FRUs that are identified on the diagnostics problem report screen. 651-630 G 307 Description: I/O Expansion Bus Parity Error. 651-631 G 307 Description: I/O Expansion Bus Time-out Error. 651-632 G 306 Description: Internal Device Error. 307 308 651-633 G 307 Description: I/O Expansion Unit not in an operating state. 306 651-634 G 307 Description: Internal Device Error. 651-639 G Description: Error log analysis indicates an error detected by the I/O. The error log indicates the following physical FRU location(s) as the probable cause(s). Action: Use the physical location codes to replace the FRUs that are identified on the diagnostics problem report screen. 651-640 G 2D5 Description: I/O general bus error. 651-641 G 2D6 Description: Secondary I/O general bus error 651-642 G 2D3 Description: Internal Service Processor memory error 651-643 G 2D3 Description: Internal Service Processor firmware error 651-644 G 2D3 Description: Other internal Service Processor hardware error 651-650 G E17 Description: ECC correctable error. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-651 G E18 Description: ECC correctable error. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-652 G 300 Description: ECC correctable error. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-653 G 301 Description: ECC correctable error. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-654 G 302 Description: ECC correctable error. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-655 G 303 Description: ECC correctable error. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-656 G 304 Description: ECC correctable error. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-657 G 305 Description: ECC correctable error. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-660 G E17 Description: Correctable error threshold exceeded. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-661 G E18 Description: Correctable error threshold exceeded. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-662 G 300 Description: Correctable error threshold exceeded. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-663 G 301 Description: Correctable error threshold exceeded. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-664 G 302 Description: Correctable error threshold exceeded. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-665 G 303 Description: Correctable error threshold exceeded. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-666 G 304 Description: Correctable error threshold exceeded. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-667 G 305 Description: Correctable error threshold exceeded. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-670 G E17 Description: Bad or missing memory. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-671 G E18 Description: Bad or missing memory. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-672 G 300 Description: Bad or missing memory. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-673 G 301 Description: Bad or missing memory. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-674 G 302 Description: Bad or missing memory. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-675 G 303 Description: Bad or missing memory. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-676 G 304 Description: Bad or missing memory. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-677 G 305 Description: Bad or missing memory. Action: Use Chapter 14. "MAP 0240: Memory Problem Resolution". 651-710 G 214 Description: Address/Data parity error on Processor bus 2C4 651-711 G 214 Description: Address/Data parity error on Processor bus 210 2C4 651-712 G 214 Description: Address/Data parity error on Processor bus 210 210 2C4 651-713 G 214 Description: Transfer error on Processor bus 2C4 651-714 G 214 Description: Transfer error on Processor bus 210 2C4 651-715 G 214 Description: Transfer error on Processor bus 210 210 2C4 651-720 G 2C5 Description: Uncorrectable Memory Error Action: Use Chapter 14. "MAP 0240: Memory 2C7 Problem Resolution". 214 651-721 G 2C6 Description: Uncorrectable Memory Error Action: Use Chapter 14. "MAP 0240: Memory 2C7 Problem Resolution". 214 651-722 G 210 Description: Processor bus parity error 2C4 214 651-723 G 210 Description: Processor bus parity error 2C4 214 651-724 G 292 Description: I/O Host Bridge time-out error 2C8 214 763 651-725 G 292 Description: I/O Host Bridge address/data parity error 2C8 214 763 651-730 G Description: I/O error on the ISA bus. Action: Refer to the Bus SRN to FRU Reference Table in the system unit's service guide. 651-731 G 2C8 Description: Intermediate or System Bus Address Parity Error. 292 763 651-732 G 2C8 Description: Intermediate or System Bus Data Parity Error. 292 763 651-733 G 214 Description: Intermediate or System Bus Address Parity Error. 2C8 292 651-734 G 214 Description: Intermediate or System Bus Data Parity Error. 2C8 292 651-735 G 2D2 Description: Intermediate or System Bus Time-out Error. 292 651-736 G 2D2 Description: Intermediate or System Bus Time-out Error. 292 214 651-740 G 2D3 Description: Time-out on communication response from Service Processor 2D4 651-741 G 2D3 Description: Service Processor error accessing special registers 2D4 651-742 G 2D3 Description: Service Processor reports unknown communication error 2D4 651-743 G 2D7 Description: Service Processor error accessing Vital Product Data EEPROM 2D5 651-744 G 165 Description: Service Processor error accessing Operator Panel 2D5 2D3 651-745 G 2D9 Description: Service Processor error accessing Power Controller 2D5 651-746 G 2E0 Description: Service Processor error accessing Fan Sensor 2D5 651-747 G 2E1 Description: Service Processor error accessing Thermal Sensor 2D5 651-748 G 2E2 Description: Service Processor error accessing Voltage Sensor 2D5 651-749 G 2E3 Description: Service Processor error accessing Serial Port 2D4 651-750 G 814 Description: Service Processor error accessing NVRAM 2D4 651-751 G 817 Description: Service Processor error accessing Real-Time Clock/Time-of-Day Clock 2D4 651-752 G 2E4 Description: Service Processor error accessing JTAG/COP controller/hardware 2D4 651-753 G 151 Description: Service Processor detects loss of voltage from the Time-of-Day Clock 2D4 backup battery 651-760 G software Description: Service Processor caused a reboot of the system due to a surveillance hardware time-out. Action: A surveillance time-out is caused by lack of response from the operating system. The most likely cause is a software or operating system failure. Verify that the problem is not related to hardware by running diagnostics, in Problem Determination Mode, on all resources which have not already been run. Also, the system administrator should look for other symptoms that would indicate a software or operating system problem. Contact the software support structure for assistance in needed. 651-770 G 2C8 Description: Intermediate or System Bus Address Parity Error. 292 306 651-771 G 2C8 Description: Intermediate or System Bus Data Parity Error. 292 306 651-772 G 2D2 Description: Intermediate or System Bus Time-out Error. 292 306 651-773 G 227 Description: Intermediate or System Bus Data Parity Error. 651-780 G E17 Description: Uncorrectable Memory Error. Action: Use Chapter 14. "MAP 0240: Memory 2C7 Problem Resolution". 214 651-781 G E18 Description: Uncorrectable Memory Error. Action: Use Chapter 14. "MAP 0240: Memory 2C7 Problem Resolution". 214 651-782 G 300 Description: Uncorrectable Memory Error. Action: Use Chapter 14. "MAP 0240: Memory 214 Problem Resolution". 651-783 G 301 Description: Uncorrectable Memory Error. Action: Use Chapter 14. "MAP 0240: Memory 214 Problem Resolution". 651-784 G 302 Description: Uncorrectable Memory Error. Action: Use Chapter 14. "MAP 0240: Memory 214 Problem Resolution". 651-785 G 303 Description: Uncorrectable Memory Error. Action: Use Chapter 14. "MAP 0240: Memory 214 Problem Resolution". 651-786 G 304 Description: Uncorrectable Memory Error. Action: Use Chapter 14. "MAP 0240: Memory 214 Problem Resolution". 651-787 G 305 Description: Uncorrectable Memory Error. Action: Use Chapter 14. "MAP 0240: Memory 214 Problem Resolution". 651-800 G 166 Description: Fan is turning slower than expected 2E0 651-801 G 166 Description: Over voltage condition was detected 2E0 Action: Verify the following: * nothing is obstructing the fan rotation * the fan power connection is tight * the fan speed sensing cable is tight If the fan still is not turning replace the fan. If the fan is turning, replace the fan sensor FRU. 651-810 G 152 Description: Over voltage condition was detected 2E2 Action: Verify that all DC voltages are within specifications. If all of the voltages are within specifications, replace the voltage sensor FRU, otherwise replace the power supply FRU. 651-811 G 152 Description: Under voltage condition was detected 2E2 Action: Verify that all DC voltages are within specifications. If all of the voltages are within specifications, replace the voltage sensor FRU, otherwise replace the power supply FRU. 651-812 G 152 Description: System shutdown due to: 1. Loss of AC power 2. Power button was pushed without proper system shutdown 3. Power supply failure Action: If reasons 1 and 2 can be ruled out than replace the power supply FRU. 651-813 G Description: System shutdown due to loss of AC Power to the site. Action: System resumed normal operation, no action required. 651-814 G 152 Description: CEC Rack shutdown due to one of the following: 1. Loss of AC power to the CEC Rack 2. Open or disconnected SPCN cable between racks 3. AC module, Bulk power, regulator or SPCN card failure. Action: If 1 and 2 can be ruled out and the problem can be recreated, try the power supply related FRUs one at a time to isolate the problem. 651-815 G 287 Description: I/O Rack shutdown due to one of the following: 289 1. Loss of AC power to the I/O Rack 2. Open or disconnected SPCN cable between racks 3. Power supply failure Action: If 1 and 2 can be ruled out, then replace the power supply FRU. 651-816 G 287 Description: Power fault due to internal power supply failure. 651-817 G 289 Description: Power fault due to internal power supply failure. 651-818 G Description: Power fault due to manual activation of power-off request. Action: Resume normal operation. 651-820 G 2E1 Description: An over temperature condition was detected Action: Verify the following: * the room ambient temperature is within the system operating environment * there is unrestricted air flow around the system * all system covers are closed If all conditions are met, then replace the temperature sensor FRU. 651-821 G 2E1 Description: System shutdown due to an over maximum temperature condition being reached. Action: Verify the following: * The room ambient temperature is within the system operating environment. * There is unrestricted air flow around the system. * All system covers are closed. If all conditions are met, then replace the temperature sensor FRU. 651-822 G 166 Description: System shutdown due to over temperature condition and fan failure. Use 2E1 the physical FRU location(s) as the probable cause(s). Action: Use the physical location codes to replace the FRUs that are identified on the diagnostics problem report screen. 651-830 G 166 Description: Sensor detected a fan failure. 2E0 Action: Use Chapter 13. "MAP 0220 Hot Plug FRU Problem Resolution". 651-831 G 152 Description: Sensor detected a voltage outside of the normal range. 2E2 Action: Use MAP 1520. 651-832 G 2E1 Description: Sensor detected an abnormally high internal temperature. Action: Verify that: 1. The room ambient temperature is within the system operating environment. 2. There is unrestricted air flow around the system. 3. All system covers are closed. 4. There are no fan failures. If none of these problems exist, then proceed with Chapter 13. "MAP 0220 Hot Plug FRU Problem Resolution". 651-833 G 152 Description: Sensor detected a power supply failure. E19 Action: Use Chapter 13. "MAP 0220 Hot Plug FRU Problem Resolution". 651-839 G Description: Sensor detected a FRU that has failed. Action: Use the physical location code(s) to replace the FRU(s) that are identified on the diagnostics problem report screen. 651-840 G 166 Description: Sensor detected a fan failure. 2E0 Action: Use Chapter 13. "MAP 0220 Hot Plug FRU Problem Resolution". 651-841 G 152 Description: Sensor detected a voltage outside of the normal range. 2E2 Action: Use MAP 1520. 651-842 G 2E1 Description: Sensor detected an abnormally high internal temperature. Action: Verify that: 1. The room ambient temperature is within the system operating environment. 2. There is unrestricted air flow around the system. 3. All system covers are closed. 4. There are no fan failures. If none of these problems exist, then proceed with Chapter 13. "MAP 0220 Hot Plug FRU Problem Resolution". 651-843 G 152 Description: Sensor detected a power supply failure. E19 Action: Use Chapter 13. "MAP 0220 Hot Plug FRU Problem Resolution". 651-849 G Description: Sensor detected a FRU that has failed. Action: Use the physical location code(s) to replace the FRU(s) that are identified on the diagnostics problem report screen. 651-88x G Description: The CEC or SPCN reported an error. Action: If reference and location codes were reported with this SRN, refer to this system unit's system service guide with the reference and location codes for the necessary repair action. If the reference and location codes were NOT reported, then run Diagnostics in Problem Determination mode and record and report the reference and location codes for this SRN. 651-89x G Description: The CEC or SPCN reported an error. Action: Refer to the this system unit's system service guide, with the reference and location codes, for the necessary repair action. If the reference and location codes were NOT reported, then run Advanced Diagnostics in Problem Determination mode and record and report the reference and location codes for this SRN. 652-600 G Description: A non-critical error has been detected and corrected: Uncorrectable memory or unsupported memory. Action: Schedule deferred maintenance. Examine the memory modules and determine if they are supported types. If the modules are supported, then replace the appropriate memory module(s). 652-610 G 210 Description: A non-critical error has been detected and corrected: CPU internal error. Action: Schedule deferred maintenance. Use Chapter 12. "MAP 0210: General Problem Resolution". 652-611 G 210 Description: A non-critical error has been detected and corrected: CPU internal cache error. Action: Schedule deferred maintenance. Use Chapter 12. "MAP 0210: General Problem Resolution" 652-612 G D01 Description: A non-critical error has been detected and corrected: L2 cache parity or multi-bit ECC error. Action: Schedule deferred maintenance. Use Chapter 12. "MAP 0210: General Problem Resolution". 652-613 G D01 Description: A non-critical error has been detected and corrected: L2 cache ECC single-bit error. Action: Schedule deferred maintenance. Use Chapter 12. "MAP 0210: General Problem Resolution" 652-622 G 2C5 Description: A non-critical error has been detected and corrected: Correctable error threshold exceeded. Action: Schedule deferred maintenance. Use Chapter 14. "MAP 0240: Memory Problem Resolution". 652-623 G 2C6 Description: A non-critical error has been detected and corrected: Correctable error threshold exceeded. Action: Schedule deferred maintenance. Use Chapter 14. "MAP 0240: Memory Problem Resolution". 652-630 G 307 Description: A non-critical error has been detected and corrected: I/O Expansion Bus Parity Error. Action: Schedule deferred maintenance. Use Chapter 12. "MAP 0210: General Problem Resolution". 652-631 G 307 Description: A non-critical error has been detected and corrected: I/O Expansion Bus Time-out Error. Action: Schedule deferred maintenance. Use Chapter 12. "MAP 0210: General Problem Resolution". 652-632 G 306 Description: A non-critical error has been detected and corrected: I/O Expansion Bus 307 Connection Failure. Action: Schedule deferred maintenance. Use 308 Chapter 12. "MAP 0210: General Problem Resolution". 652-633 G 307 Description: A non-critical error has been detected and corrected: I/O Expansion Unit 306 not in an operating state. Action: Schedule deferred maintenance. Use Chapter 12. "MAP 0210: General Problem Resolution". 652-634 G 307 Description: A non-critical error has been detected and corrected: Internal Device Error. Action: Schedule deferred maintenance. Use Chapter 12. "MAP 0210: General Problem Resolution". 652-660 G E17 Description: A non-critical error has been detected and corrected: Correctable error threshold exceeded. Action: Schedule deferred maintenance. Use Chapter 14. "MAP 0240: Memory Problem Resolution". 652-661 G E18 Description: A non-critical error has been detected and corrected: Correctable error threshold exceeded. Action: Schedule deferred maintenance. Use Chapter 14. "MAP 0240: Memory Problem Resolution". 652-662 G 300 Description: A non-critical error has been detected and corrected: Correctable error threshold exceeded. Action: Schedule deferred maintenance. Use Chapter 14. "MAP 0240: Memory Problem Resolution". 652-663 G 301 Description: A non-critical error has been detected and corrected: Correctable error threshold exceeded. Action: Schedule deferred maintenance. Use Chapter 14. "MAP 0240: Memory Problem Resolution". 652-664 G 302 Description: A non-critical error has been detected and corrected: Correctable error threshold exceeded. Action: Schedule deferred maintenance. Use Chapter 14. "MAP 0240: Memory Problem Resolution". 652-665 G 303 Description: A non-critical error has been detected and corrected: Correctable error threshold exceeded. Action: Schedule deferred maintenance. Use Chapter 14. "MAP 0240: Memory Problem Resolution". 652-666 G 304 Description: A non-critical error has been detected and corrected: Correctable error threshold exceeded. Action: Schedule deferred maintenance. Use Chapter 14. "MAP 0240: Memory Problem Resolution". 652-667 G 305 Description: A non-critical error has been detected and corrected: Correctable error threshold exceeded. Action: Schedule deferred maintenance. Use Chapter 14. "MAP 0240: Memory Problem Resolution". 652-731 G 2C8 Description: A non-critical error has been detected and corrected: Intermediate or 292 System Bus Address Parity Error. Action: Schedule deferred maintenance. Use Chapter 12. "MAP 0210: General Problem Resolution". 652-732 G 2C8 Description: A non-critical error has been detected and corrected: Intermediate or 292 System Bus Data Parity Error. Action: Schedule deferred maintenance. Use Chapter 12. "MAP 0210: General Problem Resolution". 652-733 G 214 Description: A non-critical error has been detected and corrected: Intermediate or 2C8 System Bus Address Parity Error. Action: Schedule deferred maintenance. Use 292 Chapter 12. "MAP 0210: General Problem Resolution". 652-734 G 214 Description: A non-critical error has been detected and corrected: Intermediate or 2C8 System Bus Data Parity Error. Action: Schedule deferred maintenance. Use 292 Chapter 12. "MAP 0210: General Problem Resolution". 652-735 G 2D2 Description: A non-critical error has been detected and corrected: Intermediate or 292 System Bus Time-out Error. Action: Schedule deferred maintenance. Use Chapter 12. "MAP 0210: General Problem Resolution". 652-736 G 2D2 Description: A non-critical error has been detected and corrected: Intermediate or 292 System Bus Time-out Error. Action: Schedule deferred maintenance. Use 214 Chapter 12. "MAP 0210: General Problem Resolution". 652-770 G 2C8 Description: A non-critical error has been detected and corrected: Intermediate System 292 Bus Address Parity Error. Action: Schedule deferred maintenance. Use 306 Chapter 12. "MAP 0210: General Problem Resolution". 652-771 G 2C8 Description: A non-critical error has been detected and corrected: Intermediate or 292 System Bus Data Parity Error. Action: Schedule deferred maintenance. Use 306 Chapter 12. "MAP 0210: General Problem Resolution". 652-772 G 2D2 Description: A non-critical error has been detected and corrected: Intermediate or 292 System Bus Time-out Error. Action: Schedule deferred maintenance. Use 306 Chapter 12. "MAP 0210: General Problem Resolution". 652-773 G 227 Description: A non-critical error has been detected and corrected. Intermediate or System Bus Data Parity Error. Action: Schedule deferred maintenance. Use Chapter 12. "MAP 0210: General Problem Resolution". 652-810 G 152 Description: Non-critical power problem, loss of redundant supply. Use the physical FRU location(s) as the probable cause(s). Action: Schedule maintenance. Use the physical location codes to replace the FRUs that are identified on the diagnostics problem report screen. 652-820 G 166 Description: Non-critical cooling problem, loss of redundant fan. Use the physical FRU location(s) as the probable cause(s). Action: Schedule maintenance. Use the physical location codes to replace the FRUs that are identified on the diagnostics problem report screen. 652-830 G 166 Description: Sensor detected a redundant fan failure. 2E0 Action: Use Chapter 13. "MAP 0220 Hot Plug FRU Problem Resolution". 652-833 G 152 Description: Sensor detected a redundant power supply failure. E19 Action: Use Chapter 13. "MAP 0220 Hot Plug FRU Problem Resolution". 652-839 G Description: Sensor detected a redundant FRU failure. Action: Use the physical location code(s) to replace the FRU(s) that are identified on the diagnostics problem report screen. 652-88x G Description: The CEC or SPCN reported a non-critical error. Action: Schedule deferred maintenance. If reference and location codes were reported with this SRN, refer to this system unit's system service guide with the reference and location codes for the necessary repair action. If the reference and location codes were NOT reported, then run Diagnostics in Problem Determination mode and record and report the reference and location codes for this SRN. 652-89x G Description: The CEC or SPCN reported a non-critical error. Action: Schedule deferred maintenance. Refer to the this system unit's system service guide, with the reference and location codes, for the necessary repair action. If the reference and location codes were NOT reported, then run Advanced Diagnostics in Problem Determination mode and record and report the reference and location codes for this SRN. 664-098 J 664 Description: IPLROS detected a problem with the CD-ROM drive B88 221 664-099 J 664 Description: IPLROS detected a problem with the CD-ROM drive B88 664-111 D 664 Description: Unable to reserve device. B88 664-112 D 664 Description: Unable to do configuration. B88 664-113 D 664 Description: Unable to open the device driver. B88 664-121 D 664 Description: The CD-ROM drive indicates an error. 664-122 D 664 Description: The CD-ROM drive indicates an error. 664-123 D 664 Description: The CD-ROM drive indicates an error. 664-125 D 664 Description: The CD-ROM drive indicates an error. B88 664-126 D 664 Description: The CD-ROM drive indicates an error. 664-127 D 664 Description: The CD-ROM drive indicates an error. 664-128 D 664 Description: The CD-ROM drive indicates an error. 664-129 D 664 Description: The CD-ROM drive indicates an error. 664-150 D Media Description: A media error was detected. 664 664-151 D 664 Description: A command timeout was detected. D88 664-152 D 664 Description: A command reservation conflict was detected. 664-162 D 664 Description: The CD-ROM drive indicates an error. 664-171 D 664 Description: Unable to reserve device. 664-172 D 664 Description: Unable to do configuration. 664-173 D 664 Description: Unable to open device driver. 664-175 D 664 Description: The CD-ROM drive indicates an error. 664-198 D 664 Description: Undefined error detected. B88 664-199 D 664 Description: Undefined error detected. 664-211 D 664 Description: The LED test failed. 664-281 D 664 Description: No tone during audio test. 664-301 G 664 Description: Errors found during ELA. 664-302 G 664 Description: Errors found during ELA. B88 669-201 D 669 Description: Configuration register test failure 221 669-202 D 669 Description: I/O register test failure 221 669-203 D 669 Description: Adapter memory test failure 221 669-204 D 669 Description: Adapter initialization test failure 221 669-205 D 669 Description: Internal loopback test failure 221 669-206 D 669 Description: External loopback test failure 221 669-701 G 669 Description: Error log analysis indicates that this device failed to initialize because it is not the IBM version of the adapter. AIX cannot configure the non-IBM version of this adapter 669-702 G 669 Description: Error Log Analysis indicates that this device failed to initialize due 221 to a problem with the EEPROM on the adapter. 669-703 G 669 Description: Error Log Analysis indicates that this device has failed to initialize 221 due to a self-test failure. 669-704 D 669 Description: Error Log Analysis indicates that this device has failed to initialize 221 due to firmware download error. The microcode seems to be properly installed. 674-101 D 674 Description: Artic960 PCI Adapter Central Processing Unit (CPU) test failure. C94 Action: Use MAP 0210. C95 674-102 D 674 Description: Artic960 PCI Adapter Timer test failure. C94 Action: Use MAP 0210. C95 674-103 D 674 Description: Artic960 PCI Adapter Bus Interface test failure. C94 Action: Use MAP 0210. C95 674-104 D C94 Description: Artic960 PCI Adapter Dynamic Random Access Memory (DRAM) test failure. 674 Action: Use MAP 0210. C95 674-105 D 674 Description: Artic960 PCI Adapter Memory Protection test failure. C94 Action: Use MAP 0210. C95 674-106 D 674 Description: Artic960 PCI Adapter Debug Port test failure. C94 Action: Use MAP 0210. C95 674-107 D C95 Description: Interface board wrap test failure. 674 Action: Use MAP 0210. C97 674-110 D C94 Description: Artic960 PCI Adapter Download Diagnostics test failure. 674 Action: Use MAP 0210. C95 674-123 D C95 Description: Interface board non-wrap test failure. C98 Action: Use MAP 0210. C97 674-150 D 674 Description: Device configuration failure. software Action: Use MAP 0210. 227 674-151 D 674 Description: Device driver indicates a hardware failure. software Action: Use MAP 0210. 227 674-152 D 674 Description: Failure and error in determining which type of Artic960 PCI Adapter. Action: Use MAP 0210. 674-153 D 674 Description: Error log analysis indicates a Artic960 PCI Adapter failure. 227 Action: Use ERRPT command to check error log. C94 software 674-154 D C94 Description: Artic960 PCI Adapter initialization failure. 674 Action: Use MAP 0210. C95 674-155 D 674 Description: Artic960 PCI Adapter initialization failure. C94 Action: Use MAP 0210. C95 674-156 D C95 Description: Artic960 PCI Adapter initialization failure. 674 Action: Use MAP 0210. C94 674-157 D C98 Description: Cable wrap test failure. Action: Use MAP 0210. C97 C95 675-101 D 675 Description: Artic960Hx Adapter Central Processing Unit (CPU) test failure. C94 Action: Use MAP 0210. C95 675-102 D 675 Description: Artic960Hx Adapter Timer test failure. C94 Action: Use MAP 0210. C95 675-103 D 675 Description: Artic960Hx Adapter Bus Interface test failure. C94 Action: Use MAP 0210. C95 675-104 D C94 Description: Artic960Hx Adapter Dynamic Random Access Memory (DRAM) test failure. 675 Action: Use MAP 0210. C95 675-105 D 675 Description: Artic960Hx Adapter Memory Protection test failure. C94 Action: Use MAP 0210. C95 675-106 D 675 Description: Artic960Hx Adapter Debug Port test failure. C94 Action: Use MAP 0210. C95 675-107 D C95 Description: Interface board wrap test failure. 675 Action: Use MAP 0210. C97 675-110 D C94 Description: Artic960Hx Adapter Download Diagnostics test failure. 675 Action: Use MAP 0210. C95 675-123 D C95 Description: Interface board non-wrap test failure. C98 Action: Use MAP 0210. C97 675-150 D 675 Description: Device configuration failure. software Action: Use MAP 0210. 227 675-151 D 675 Description: Device driver indicates a hardware failure. software Action: Use MAP 0210. 227 675-152 D 675 Description: Failure and error in determining which type of Artic960Hx Adapter. Action: Use MAP 0210. 675-153 D 675 Description: Error log analysis indicates a Artic960Hx Adapter failure. 227 Action: Use ERRPT command to check error log. C94 software 675-154 D C94 Description: Artic960Hx Adapter initialization failure. 675 Action: Use MAP 0210. C95 675-155 D 675 Description: Artic960Hx Adapter initialization failure. C94 Action: Use MAP 0210. C95 675-156 D C95 Description: Artic960Hx Adapter initialization failure. 675 Action: Use MAP 0210. C94 675-157 D C98 Description: Cable wrap test failure. Action: Use MAP 0210. C97 C95 677-201 D 677 Description: Configuration Register test failure 221 677-202 D 677 Description: Reset test failure 221 677-203 D 677 Description: Register test failure 221 677-204 D 677 Description: SRAM test failure 221 677-205 D 677 Description: Interrupt test failure 221 677-206 D 677 Description: PCI Loop Back test failure 221 677-207 D 677 Description: Internal Loop Back test failure 221 677-208 D 677 Description: External Loop Back test failure 221 677-209 D 677 Description: Hub Loop Back test failure xxx 677-301 D 677 Description: I/O Error on Read/Write Operation 221 Software 677-401 F C24 Description: Unisolated Loop Back test failure xxx Action: Run diagnostics again utilizing the wrap plug. 677 221 677-701 G 677 Description: Error log analysis indicates that an error has occurred with the 221 adapter. 677-702 G Microcode Description: Error log analysis indicates that an adapter microcode error has 677 occurred 678-098 J 678 Description: Tape drive indicates an error. 678-099 J 678 Description: Tape drive not found. B88 678-101 Description: Timeout while attempting to D 678 communicate with SCSI device. Description: The SCSI device indicates 678-102 D 678 busy. 678-103 Description: The SCSI device indicates a D 678 reservation conflict. 678-104 Description: The SCSI device indicates a D 678 check condition. 678-105 Description: An error is detected in D 678 request sense data. 678-107 Description: Sense data from the SCSI D 678 drive has unexpected data. 678-110 Description: The Reserve command failed. D 678 678-111 Description: Invalid condition from the D 678 drive after a reserve. 678-112 Description: The write protect sensor D 678 test failed. 678-113 Description: Invalid condition from drive D 678 after a request sense. 678-114 Description: Timeout while attempting to D 678 communicate with the SCSI device. Description: The Inquiry command failed. 678-120 D 678 678-130 Description: The Load command failed. D 678 media 678-134 Description: The adapter failed to D B88 configure. software 678-135 Description: The Unload command failed. D 678 media 678-140 Description: The Mode Select command D 678 failed. 678-150 Description: The Test Unit Ready command D 678 failed. media 678-160 Description: The Send Diagnostic command D 678 failed. media 678-161 Description: Invalid condition from the D 678 drive after a reserve. B88 678-163 Description: Invalid condition from the D 678 drive after a request sense. B88 678-164 Description: Timeout while attempting to D 678 communicate with the SCSI device. B88 Description: Write, Read and Compare Test 678-165 D 678 failed. B88 276 678-166 Description: Unable to configure the D 678 device. B88 software 678-167 Description: An unexpected SCSI error D 678 occurred. B88 678-168 Description: The adapter failed to D B88 configure. software 678-169 Description: The send diagnostic command D 678 failed. media 678-170 Description: The Read, Write and Compare D 678 test failed. B88 media 678-180 Description: The Load command failed. D 678 media 678-185 Description: The Unload command failed. D 678 media 678-190 Description: The Mode Select command D 678 failed. 678-200 Description: The Test Unit Ready command D 678 failed. media 678-201 Description: Error diagnosed from error G 678 log analysis. B88 678-210 Description: The device configuration D 678 failed. B88 678-211 Description: The device open failed. D 678 B88 678-220 Description: The Release command failed. D 678 678-230 Description: The Request Sense command D 678 failed. 678-240 Description: The Openx command failed. D 678 678-260 Description: The device configuration D 678 failed. 678-261 Description: The device open failed. D 678 678-300 Description: The device configuration D 678 failed. software 678-310 Description: SCSI adapter configuration D B88 failed. 678 software 678-320 Description: Error log analysis indicates G 678 a failure. media 678-411 Description: A reservation conflict to D 678 occurred. 678-423 B88 software 678-511 Description: The drive returned bad or to D 678 non-extended sense data. 678-523 B88 678-611 Description: An adapter or bus I/O error to D 678 occurred. 678-623 B88 software 678-711 Description: A device timeout error to D 678 occurred. 678-723 B88 software 679-098 Description: The disk drive indicates an J 679 error. B88 679-099 Description: The disk drive not found. J 679 B88 679-102 Description: An unrecoverable media error D 679 occurred. 679-104 Description: The motor failed to restart. D 679 679-105 Description: The drive did not become D 679 ready. 679-106 Description: The electronics card test D 679 failed. 679-108 Description: The bus test failed. D 679 679-110 Description: The media format is D 679 corrupted. 679-112 Description: The diagnostic test failed. D 679 679-114 Description: An unrecoverable hardware D 679 error. 679-116 Description: A protocol error. D Action: Check the levels of the device, adapter, diagnostic software, and application software to be sure they are all compatible. If you do not find a problem, call your support person. 679-117 Description: A write protect error D 679 occurred. 679-118 Description: A SCSI command time-out D 679 occurred. B88 679-120 Description: A SCSI busy or command D 679 error. 679-122 Description: A SCSI reservation conflict D 679 error. 679-124 Description: A SCSI check condition error D 679 occurred. 679-126 Description: A software error was caused D 679 by a hardware failure. B88 679-128 Description: The error log analysis G 679 indicates a hardware failure. 679-129 G D50 Description: Error log analysis indicates a SCSI bus problem. 679 B88 software 679-130 G 679 Description: Error log analysis indicates a problem reported by the disk drive's self monitoring function. 679-132 Description: A disk drive hardware error D 679 occurred. 679-134 Description: The adapter failed to D B88 configure. software 679-135 D 679 Description: The device failed to B88 configure. software 679-136 Description: The certify operation D 679 failed. save 679-137 D 679 Description: Unit attention condition has occurred on the Send Diagnostic command. B88 D50 681-098 J 681 Description: The disk drive indicates an error. B88 681-099 J 681 Description: The disk drive not found. B88 681-102 D 681 Description: An unrecoverable media error occurred. 681-104 D 681 Description: The motor failed to restart. 681-105 D 681 Description: The drive did not become ready. 681-106 D 681 Description: The electronics card test failed. 681-108 D 681 Description: The bus test failed. 681-110 D 681 Description: The media format is corrupted. 681-112 D 681 Description: The diagnostic test failed. 681-114 D 681 Description: An unrecoverable hardware error. 681-116 D Description: A protocol error. Action: Check the levels of the device, adapter, diagnostic software, and application software to be sure they are all compatible. If you do not find a problem, call your support person. 681-117 D 681 Description: A write protect error occurred. 681-118 D 681 Description: A SCSI command time-out occurred. B88 681-120 D 681 Description: A SCSI busy or command error. 681-122 D 681 Description: A SCSI reservation conflict error. 681-124 D 681 Description: A SCSI check condition error occurred. 681-126 D 681 Description: A software error was caused by a hardware failure. B88 681-128 G 681 Description: The error log analysis indicates a hardware failure. 681-129 G D50 Description: Error log analysis indicates a SCSI bus problem. 681 B88 software 681-130 G 681 Description: Error log analysis indicates a problem reported by the disk drive's self monitoring function. 681-132 D 681 Description: A disk drive hardware error occurred. 681-134 D B88 Description: The adapter failed to configure. software 681-135 D 681 Description: The device failed to configure. B88 software 681-136 D 681 Description: The certify operation failed. 681-137 D 681 Description: Unit attention condition has occurred on the Send Diagnostic command. B88 D50 682-098 J 682 Description: IPLROS detected a problem with the CD-ROM drive B88 221 682-099 J 682 Description: IPLROS detected a problem with the CD-ROM drive B88 682-111 D 682 Description: Unable to reserve device. B88 682-112 D 682 Description: Unable to do configuration. B88 682-113 D 682 Description: Unable to open the device driver. B88 682-121 D 682 Description: The CD-ROM drive indicates an error. 682-122 D 682 Description: The CD-ROM drive indicates an error. 682-123 D 682 Description: The CD-ROM drive indicates an error. 682-125 D 682 Description: The CD-ROM drive indicates an error. B88 682-126 D 682 Description: The CD-ROM drive indicates an error. 682-127 D 682 Description: The CD-ROM drive indicates an error. 682-128 D 682 Description: The CD-ROM drive indicates an error. 682-129 D 682 Description: The CD-ROM drive indicates an error. 682-150 D Media Description: A media error was detected. 682 682-151 D 682 Description: A command timeout was detected. D88 682-152 D 682 Description: A command reservation conflict was detected. 682-162 D 682 Description: The CD-ROM drive indicates an error. 682-171 D 682 Description: Unable to reserve device. 682-172 D 682 Description: Unable to do configuration. 682-173 D 682 Description: Unable to open device driver. 682-175 D 682 Description: The CD-ROM drive indicates an error. 682-198 D 682 Description: Undefined error detected. B88 682-199 D 682 Description: Undefined error detected. 682-211 D 682 Description: The LED test failed. 682-281 D 682 Description: No tone during audio test. 682-301 G 682 Description: Errors found during ELA. 682-302 G 682 Description: Errors found during ELA. B88 685-001 D 685 Description: RGB_SCREEN_USER_FAIL Monitor/ cable 685-040 D 685 Description: STATUS_POLL_TIMEOUT_ERROR 227 Monitor/ cable 685-041 D 685 Description: CRC_POLL_TIMEOUT_ERROR 227 Monitor/ cable 685-060 D software Description: SVC_AIDS_INPUT_ERROR 685 685-081 D software Description: LOOP_COUNT_WAS_ZERO 685 685-082 D software Description: INVALID_TU_NUMBER 685 685-0B0 D software Description: ROM test failed 685 685-0B1 D software Description: ROM test failed 685 685-0D0 D software Description: INTERNAL_ERROR_DATA_SIZE_0 685 685-0D1 D software Description: INTERNAL_ERROR_DATA_SIZE_1 685 685-0D2 D software Description: INTERNAL_ERROR_DATA_SIZE_2 685 685-0D3 D software Description: INTERNAL_ERROR_DATA_SIZE_3 685 685-0D5 D software Description: ODM INIT FAILED 685 685-0D6 D software Description: ODM_OBJECT_SEARCH_FAILED 685 685-0D8 D software Description: ODM_GET_OBJECT_FAILED 685 685-0D9 D software Description: ODM_TERM_FAILED 685 685-0DB D software Description: ILLEGAL_RESOLUTION_SPECIFIED 685 685-0E5 D software Description: AIXGSC_MGA_START_INTERRUPT_FAILED 685 685-0E6 D software Description: AIXGSC_MGA_STOP_INTERRUPT_FAILED 685 685-0E7 D software Description: MDD_OPEN_BUS_FAILED 685 685-0E8 D software Description: MDD_IOCTL_ERROR 685 685-0E9 D software Description: OPEN_RCM_ERROR 685 685-0EA D software Description: IOCTL_GSC_HANDLE_FAILED 685 685-0EB D software Description: AIXGSC_MAKE_GP_FAILED 685 685-0EC D software Description: AIXGSC_UNMAKE_GP_FAILED 685 685-0ED D software Description: DEVICE_BUSY_ERROR 685 685-0EE D software Description: AIXGSC_MGA_SET_DISPLAY_FAILED 685 685-100 D 685 Description: REG_32_BIT_PRTN_ERROR 227 Monitor/ cable 685-101 D 685 Description: REG_32_BIT_ADDR_UNIQ_ERROR 227 Monitor/ cable 685-102 D 685 Description: REG_8_BIT_PTRN_ERROR 227 Monitor/ cable 685-103 D 685 Description: REG_8_BIT_ADDR_UNIQ_ERROR 227 Monitor/ cable 685-104 D 685 Description: CRTC_REGS_PTRN_ERROR 227 Monitor/ cable 685-105 D 685 Description: CRTC_REGS_ADDR_UNIQ_ERROR 227 Monitor/ cable 685-106 D 685 Description: CRTCEXT_REGS_PTRN_ERROR 227 Monitor/ cable 685-107 D 685 Description: CRTCEXT_REGS_ADDR_UNIQ_ERROR 227 Monitor/ cable 685-108 D 685 Description: RAMDAC_REGS_PTRN_ERROR 227 Monitor/ cable 685-109 D 685 Description: RAMDAC_REGS_ADDR_UNIQ_ERROR 227 Monitor/ cable 685-10A D 685 Description: PALETTE_REGS_PTRN_ERROR 227 Monitor/ cable 685-10B D 685 Description: PALETTE_REGS_ADDR_UNIQ_ERROR 227 Monitor/ cable 685-200 D 685 Description: ROM test failed 227 685-201 D 685 Description: ROM test failed 227 685-202 D 685 Description: ROM test failed 227 685-203 D 685 Description: ROM test failed 227 685-204 D 685 Description: ROM test failed 227 685-205 D 685 Description: ROM test failed 227 685-206 D 685 Description: ROM test failed 227 685-207 D 685 Description: ROM test failed 227 685-208 D 685 Description: ROM test failed 227 685-209 D 685 Description: ROM test failed 227 685-20B D 685 Description: ROM test failed 227 685-400 D 685 Description: SGRAM_RED_SCREEN_ERROR 227 Monitor/ cable 685-401 D 685 Description: SGRAM_GREEN_SCREEN_ERROR 227 Monitor/ cable 685-402 D 685 Description: SGRAM_BLUE_SCREEN_ERROR 227 Monitor/ cable 685-403 D 685 Description: SGRAM_WHITE_SCREEN_ERROR 227 Monitor/ cable 685-404 D 685 Description: SGRAM_INCREMENTING_SCREEN_ERROR 227 Monitor/ cable 685-500 D 685 Description: BLIT_TEST_ERROR_640 x 480 227 Monitor/ cable 685-501 D 685 Description: BLIT_TEST_ERROR_800 x 600 227 Monitor/ cable 685-502 D 685 Description: BLIT_TEST_ERROR_1024 x 768 227 Monitor/ cable 685-503 D 685 Description: BLIT_TEST_ERROR_1280 x 1024 227 Monitor/ cable 685-504 D software Description: INTERNAL_ERROR_DATA_SIZE_4 685 685-600 D 685 Description: DRAW_TEST_ERROR_640 x 480_A 227 Monitor/ cable 685-601 D 685 Description: DRAW_TEST_ERROR_800 x 600_A 227 Monitor/ cable 685-602 D 685 Description: DRAW_TEST_ERROR_1024 x 768_A 227 Monitor/ cable 685-603 D 685 Description: DRAW_TEST_ERROR_1280 x 1024_A 227 Monitor/ cable 685-604 D software Description: INTERNAL_ERROR_DATA_SIZE_5 685 685-605 D 685 Description: DRAW_TEST_ERROR_640 x 480_B 227 Monitor/ cable 685-606 D 685 Description: DRAW_TEST_ERROR_800 x 600_B 227 Monitor/ cable 685-607 D 685 Description: DRAW_TEST_ERROR_1024 x 768_B 227 Monitor/ cable 685-608 D 685 Description: DRAW_TEST_ERROR_1280 x 1024_B 227 Monitor/ cable 685-609 D software Description: INTERNAL_ERROR_DATA_SIZE_6 685 685-60A D 685 Description: DRAW_TEST_ERROR_640 x 480_C 227 Monitor/ cable 685-60B D 685 Description: DRAW_TEST_ERROR_800 x 600_C 227 Monitor/ cable 685-60C D 685 Description: DRAW_TEST_ERROR_1024 x 768_C 227 Monitor/ cable 685-60D D 685 Description: DRAW_TEST_ERROR_1280 x 1024_C 227 Monitor/ cable 685-60E D software Description: INTERNAL_ERROR_DATA_SIZE_7 685 686-114 D 686 Description: The register verification test failed. 686-124 D 686 Description: The adapter RAM verification test failed. 686-152 D 686 Description: The data wrap communication test failed. Note: The cable could be defective. The cable FRU part number is listed along with the adapter under FFC 686. 686-153 D 686 Description: The modem control line test failed. 686-252 D 686 Description: The data wrap communication test failed. 686-253 D 686 Description: The modem control line test failed. 686-501 D 686 Description: Adapter Reset failed 686-511 D 686 Description: Adapter to host memory test failed (byte tag test) 686-512 D 686 Description: Adapter to host memory test failed (word tag test) 686-513 D 686 Description: Adapter to host memory test failed (byte pattern test) 686-514 D 686 Description: Adapter to host memory test failed (word pattern test) 686-521 D 686 Description: Adapter BIOS POST CPU failed 686-522 D 686 Description: Adapter BIOS POST Checksum failed 686-523 D 686 Description: Adapter BIOS POST Timer failed 686-524 D 686 Description: Adapter BIOS POST RAM failed 686-526 D 686 Description: Adapter BIOS POST Async Ports failed 686-527 D 686 Description: Adapter BIOS Misc. failed 686-528 D 686 Description: Adapter BIOS Reset failed 686-529 D 686 Description: Adapter BIOS Download failed 686-531 D 686 Description: Adapter BIOS Command failed 686-533 D 686 Description: Adapter BIOS Timer test failed 686-534 D 686 Description: Adapter BIOS RAM test failed 686-541 D 686 Description: Port async internal loopback test failed (general) 686-542 D 686 Description: Port async internal loopback test failed (no response from the port) 686-551 D 686 Description: Port async external loopback test failed (general) 686-552 D 686 Description: Port async external loopback test failed (data signals) 686-553 D 686 Description: Port async external loopback test failed (control signals) 686-554 D 686 Description: Port async external loopback test failed (modem signals) 686-555 D 686 Description: Port async external loopback test failed (no response from port) 686-901 D software Description: An unexpected error occurred that can be attributed to software or to 686 hardware. Action: Run diagnostics from a source other 686-920 than from the disk or a network. If the same error occurs or if the original SRN was not obtained from disk or a network based diagnostics, use Chapter 12. "MAP 0210: General Problem Resolution" with a FFC of 686; otherwise, suspect a software problem. 686-921 D 686 Description: The adapter failed to configure. software 686-922 D software Description: An unexpected error occurred that can be attributed to software or to 686 hardware. Action: Run diagnostics from a source other 686-924 than from the disk or a network. If the same error occurs or if the original SRN was not obtained from disk or a network based diagnostics, use Chapter 12. "MAP 0210: General Problem Resolution" with a FFC of 686; otherwise, suspect a software problem. 686-925 D 686 Description: The adapter failed to configure. software 686-926 D software Description: An unexpected error occurred that can be attributed to software or to 686 hardware. Action: Run diagnostics from a source other 686-950 than from the disk or a network. If the same error occurs or if the original SRN was not obtained from disk or a network based diagnostics, use Chapter 12. "MAP 0210: General Problem Resolution" with a FFC of 686; otherwise, suspect a software problem. 687-114 D 687 Description: The register verification test failed. 687-124 D 687 Description: The adapter RAM verification test failed. 687-152 D 687 Description: The data wrap communication test failed. 837 684 152 687-153 D 687 Description: The modem control line test failed. 687-252 D 687 Description: The data wrap communication test failed. 687-253 D 687 Description: The modem control line test failed. 687-144 D 687 Description: The sync line test failed. 687-244 D 687 Description: The sync line test failed. 687-501 D 687 Description: Adapter Reset failed 687-502 D 687 Description: Adapter Fuse failed 687-511 D 687 Description: Adapter to host memory test failed (byte tag test) 687-512 D 687 Description: Adapter to host memory test failed (word tag test) 687-513 D 687 Description: Adapter to host memory test failed (byte pattern test) 687-514 D 687 Description: Adapter to host memory test failed (word pattern test) 687-521 D 687 Description: Adapter BIOS POST CPU failed 687-522 D 687 Description: Adapter BIOS POST Checksum failed 687-523 D 687 Description: Adapter BIOS POST Timer failed 687-524 D 687 Description: Adapter BIOS POST RAM failed 687-525 D 687 Description: Adapter BIOS POST Sync Line failed 687-527 D 687 Description: Adapter BIOS Misc. failed 687-528 D 687 Description: Adapter BIOS Reset failed 687-529 D 687 Description: Adapter BIOS Download failed 687-531 D 687 Description: Adapter BIOS Command failed 687-533 D 687 Description: Adapter BIOS Timer test failed 687-534 D 687 Description: Adapter BIOS RAM test failed 687-541 D 687 Description: Port sync internal loopback test failed 687-551 D 687 Description: Port sync external loopback test failed 687-600 D 837 Description: 232RAN status test failed 687-700 D 684 Description: 422RAN status test failed 687-901 D software Description: An unexpected error occurred that can be attributed to software or to 687 hardware. Action: Run diagnostics from a source other 687-920 than from the disk or a network. If the same error occurs or if the original SRN was not obtained from disk or a network based diagnostics, use Chapter 12. "MAP 0210: General Problem Resolution" with a FFC of 687; otherwise, suspect a software problem. 687-921 D software Description: The adapter failed to configure. 687 687-922 D software Description: An unexpected error occurred to that can be attributed to software or 687-924 687 hardware. Action: Run diagnostics from a source other than from the disk or a network. If the same error occurs or if the original SRN was not obtained from disk or a network based diagnostics, use Chapter 12. "MAP 0210: General Problem Resolution" with a FFC of 687; otherwise, suspect a software problem. 687-925 D 687 Description: The adapter failed to configure. software 687-926 D software Description: An unexpected error occurred that can be attributed to software or to 687 hardware. Action: Run diagnostics from a source other 687-950 than from the disk or a network. If the same error occurs or if the original SRN was not obtained from disk or a network based diagnostics, use Chapter 12. "MAP 0210: General Problem Resolution" with a FFC of 687; otherwise, suspect a software problem. 689-098 Description: The disk drive indicates an J 689 error. B88 689-099 Description: The disk drive not found. J 689 B88 689-102 Description: An unrecoverable media error D 689 occurred. 689-104 Description: The motor failed to restart. D 689 689-105 Description: The drive did not become D 689 ready. 689-106 Description: The electronics card test D 689 failed. 689-108 Description: The bus test failed. D 689 689-110 Description: The media format is D 689 corrupted. 689-112 Description: The diagnostic test failed. D 689 689-114 Description: An unrecoverable hardware D 689 error. 689-116 Description: A protocol error. D Action: Check the levels of the device, adapter, diagnostic software, and application software to be sure they are all compatible. If you do not find a problem, call your support person. 689-117 Description: A write protect error D 689 occurred. 689-118 Description: A SCSI command time-out D 689 occurred. B88 689-120 Description: A SCSI busy or command D 689 error. 689-122 Description: A SCSI reservation conflict D 689 error. 689-124 Description: A SCSI check condition error D 689 occurred. 689-126 Description: A software error was caused D 689 by a hardware failure. B88 689-128 Description: The error log analysis G 689 indicates a hardware failure. 689-129 G D50 Description: Error log analysis indicates a SCSI bus problem. 689 B88 software 689-130 G 689 Description: Error log analysis indicates a problem reported by the disk drive's self monitoring function. 689-132 Description: A disk drive hardware error D 689 occurred. 689-134 Description: The adapter failed to D B88 configure. software 689-135 D 689 Description: The device failed to B88 configure. software 689-136 Description: The certify operation D 689 failed. save 689-137 D 689 Description: Unit attention condition has occurred on the Send Diagnostic command. B88 D50 690-098 Description: The disk drive indicates an J 690 error. B88 690-099 Description: The disk drive not found. J 690 B88 690-102 Description: An unrecoverable media error D 690 occurred. 690-104 Description: The motor failed to restart. D 690 690-105 Description: The drive did not become D 690 ready. 690-106 Description: The electronics card test D 690 failed. 690-108 Description: The bus test failed. D 690 690-110 Description: The media format is D 690 corrupted. 690-112 Description: The diagnostic test failed. D 690 690-114 Description: An unrecoverable hardware D 690 error. 690-116 Description: A protocol error. D Action: Check the levels of the device, adapter, diagnostic software, and application software to be sure they are all compatible. If you do not find a problem, call your support person. 690-117 Description: A write protect error D 690 occurred. 690-118 Description: A SCSI command time-out D 690 occurred. B88 690-120 Description: A SCSI busy or command D 690 error. 690-122 Description: A SCSI reservation conflict D 690 error. 690-124 Description: A SCSI check condition error D 690 occurred. 690-126 Description: A software error was caused D 690 by a hardware failure. B88 690-128 Description: The error log analysis G 690 indicates a hardware failure. 690-129 G D50 Description: Error log analysis indicates a SCSI bus problem. 690 B88 software 690-130 G 690 Description: Error log analysis indicates a problem reported by the disk drive's self monitoring function. 690-132 Description: A disk drive hardware error D 690 occurred. 690-134 Description: The adapter failed to D B88 configure. software 690-135 D 690 Description: The device failed to B88 configure. software 690-136 D 690 Description: The certify operation failed. 690-137 D 690 Description: Unit attention condition has occurred on the Send Diagnostic command. B88 D50 691-200 D 691 Description: The ATM 25Mbps Adapter open test failed. 227 691-202 D 691 Description: The ATM 25Mbps Adapter register test failed. 227 691-203 D 691 Description: The ATM 25Mbps Adapter memory test failed. 227 691-204 D 691 Description: The ATM 25Mbps Adapter NVRAM test failed. 227 691-205 D 691 Description: The ATM 25Mbps Adapter interrupt test failed. 227 691-206 D 691 Description: The ATM 25Mbps Adapter wrap test failed. 227 691-210 D 691 Description: The ATM 25Mbps Adapter close test failed. 227 691-220 D 691 Description: The ATM 25Mbps Adapter was not found. 227 Action: Re-install the ATM 25Mbps Adapter and re-run the test. If the error continues, use Chapter 12. "MAP 0210: General Problem Resolution". 691-300 D Wrap Plug Description: The ATM 25Mbps Adapter wrap test failed. 691 Action: Re-install the wrap plug and re-run the test. If the error continues, use 227 Chapter 12. "MAP 0210: General Problem Resolution". 691-700 G 691 Description: Error log analysis reported a hardware error. 227 692-110 D 692 Description: The Reserve command failed. 692-120 D 692 Description: The Inquiry command failed. 692-130 D 692 Description: The Load command failed. media 692-135 D 692 Description: The Unload command failed. media 692-140 D 692 Description: The Mode Select command failed. 692-150 D 692 Description: The Test Unit Ready command failed. media 692-160 D 692 Description: The Send Diagnostic command failed. media 692-169 D 692 Description: The send diagnostic command failed. media 692-170 D 692 Description: The Read, Write and Compare test failed. B88 media 692-180 D 692 Description: The Load command failed. media 692-185 D 692 Description: The Unload command failed. media 692-190 D 692 Description: The Mode Select command failed. 692-200 D 692 Description: The Test Unit Ready command failed. media 692-210 D 692 Description: The device configuration failed. B88 692-220 D 692 Description: The Release command failed. 692-230 D 692 Description: The Request Sense command failed. 692-240 D 692 Description: The Openx command failed. 692-300 D 692 Description: The device configuration failed. software 692-310 D B88 Description: SCSI adapter configuration failed. 692 software 692-320 G 692 Description: Error log analysis indicates a failure. media 692-411 D 692 Description: A reservation conflict to occurred. 692-423 B88 software 692-511 D 692 Description: The drive returned bad or to non-extended sense data. 692-523 B88 692-611 D 692 Description: An adapter or bus I/O error to occurred. 692-623 B88 software 692-711 D 692 Description: A device timeout error to occurred. 692-723 B88 software 693-100 D 693 Description: Adapter open failed. 227 693-101 D 693 Description: Adapter config register test failed. 227 693-102 D 693 Description: Adapter reset failed. 227 693-103 D 693 Description: Adapter I/O register test failed. 227 693-104 D 693 Description: Adapter microcode download test failed. 227 693-105 D 693 Description: Adapter internal wrap test failed. 227 693-106 D 693 Description: Adapter close failed. 227 697-100 D 697 Description: Charm memory write failure software 227 697-101 D 697 Description: Charm memory read failure software 227 697-102 D 697 Description: PCI configuration register write failure software 227 697-103 D 697 Description: Charm software reset failure software 227 697-104 D 697 Description: Packet memory error software 227 697-105 D 697 Description: Control memory failure software 227 697-106 D 697 Description: Link-R detected bad parity 697-107 D 697 Description: Suni detected bad parity 697-108 D 697 Description: Suni initialization failure 697-109 D Wrap Plug Description: Loss of light detected in Link test 697 Action: Check wrap plug installation. 697-10B D Wrap Plug Description: External Loopback failed Action: Check wrap plug installation. 697 697-10C D 697 Description: Internal Loopback failed software 227 697-10D D 697 Description: DMS failed 227 software 697-1FF D 697 Description: EPROM checksum failed software 227 697-200 D software Description: Klog error 697 227 697-201 D software Description: ASL error 697 227 697-202 D software Description: ODM Initialization error 697 227 697-203 D software Description: Diagnostic configuration failure 697 227 697-205 D software Description: Error in diag open 697 227 697-206 D software Description: Error in releasing adapter 697 227 698-100 D 698 Description: Charm memory write failure software 227 698-101 D 698 Description: Charm memory read failure software 227 698-102 D 698 Description: PCI configuration register write failure software 227 698-103 D 698 Description: Charm software reset failure software 227 698-104 D 698 Description: Packet memory error software 227 698-105 D 698 Description: Control memory failure software 227 698-106 D 698 Description: Link-R detected bad parity 698-107 D 698 Description: Suni detected bad parity 698-108 D 698 Description: Suni initialization failure 698-109 D Wrap Plug Description: Loss of light detected in Link test 698 Action: Check wrap plug installation. 698-10B D Wrap Plug Description: External Loopback failed Action: Check wrap plug installation. 698 698-10C D 698 Description: Internal Loopback failed software 227 698-10D D 698 Description: DMS failed 227 software 698-1FF D 698 Description: EPROM checksum failed software 227 698-200 D software Description: Klog error 698 227 698-201 D software Description: ASL error 698 227 698-202 D software Description: ODM Initialization error 698 227 698-203 D software Description: Diagnostic configuration failure 698 227 698-205 D software Description: Error in diag open 698 227 698-206 D software Description: Error in releasing adapter 698 227 699-100 D 699 Description: An error was found on the adapter 699-110 G 699 Description: Error Log analysis indicates a hardware error. 699-120 D 699 Description: Adapter hardware has caused a software failure.