Dump Codes (0c1 -0cc)
0c0 The dump completed successfully
0c1 Dump Failed Due to an I/O Error
0c2 Dump, requested by user, is started.
0c3 Dump is inhibited
0c4 Dump Device Not Large Enough
0c5 Dump Did Not Start or Dump Crashed.
0c6 Dumping to Secondary Dump Device
0c7 Reserved
0c8 Dump function is disabled.
0c9 A dump is in progress
0cc Unknown Dump Failure (prior to rel 42G)/Dumping to secondary dump device.
Crash Codes
Note: Crash Codes are part of a flashing "888" message of the type "888 102 xxx yyy"
where the "xxx" is the crash code and the "yyy" is the dump status (code).
000 Unexpected system interrupt.
200 Machine check because of a memory bus error.
201 Machine check because of a memory timeout.
202 Machine check because of a memory card failure.
203 Machine check because of a out of range address.
204 Machine check because of an attempt to write to ROS (Read Only Storage).
205 Machine check because of an uncorrectable address parity.
206 Machine check because of an uncorrectable ECC error.
207 Machine check because of an unidentified error.
208 Machine check due to an L2 cache Uncorrectable ECC.
2E6 The PCI Differential Ultra SCSI adapter or the Universal PCI Differential
2E7 Configuration method unable to determine if the SCSI adapter type is
SE or DE type.
300 Data storage interrupt from the processor.
32x Data storage interrupt because of an I/O exception from the IOCC.
38x Data storage interrupt because of an I/O exception from the SLA.
400 Instruction storage interrupt.
558 There is not enough memory to continue the IPL.
600 Alignment Interrupt (Replaces former 600 crash code
605 AIX has crashed because the Portability Assist Layer (PAL) for
this machine type has detected a problem.
700 Program Interrupt (invalid instructions, traps, and panics).
800 Floating Point function not available.
BIST Codes (100 - 199)
100 BIST completed successfully control was passed to ROS.
101 Initial BIST started following RESET.
102 BIST started following Power-On-RESET.
103 BIST could not determine the system model number.
104 BIST could not find the CBA.
105 BIST could not read from the OCS EPROM.
106 BIST detected a module failure.
111 BIST detected a module failure.
112 Checkstop occurred during BIST and results could not be logged out.
113 The BIST checkstop count was greater than 1.
120 BIST started CRC check on 8752 EPROM
121 BIST detected a bad CRC on the OCS EPROM.
122 BIST started CRC check on the OCS EPROM.
123 BIST detected a bad CRC on the OCS NVRAM.
124 BIST started CRC check on the OCS NVRAM.
125 BIST detected a bad CRC on the time of day NVRAM.
126 BIST started CRC check on the time of day NVRAM.
127 BIST detected a bad CRC on the 8752 EPROM
130 BIST presence test started.
140 BIST Failed.
142 BIST Failed.
143 Invalid Memory Configuration.
144 BIST Failed.
151 BIST started AIPGM test code.
152 BIST started DCLST test code.
153 BIST started ACLST test code.
154 BIST started AST test code.
160 Bad EPOW signal/Power status signal
180 BIST logout failed.
182 BIST: COP bus not responding.
185 Checkstop occurred during BIST.
186 System generated checkstop (systems without BIST)
187 Graphics generated checkstop
195 BIST logout completed.
POST Codes (200 to 299)
200 Boot attempted with keylock in the secure position.
201 Checkstop occurred during boot.
202 Unexpected machine check interrupt.
203 Unexpected data storage interrupt.
204 Unexpected instruction storage interrupt.
205 Unexpected external interrupt..
206 Unexpected alignment interrupt.
207 Unexpected program interrupt.
208 Unexpected floating point unavailable.
209 Unexpected SVC interrupt.
20c Error detected in L2 cache (when LED persists for 5 seconds).
210 Unexpected SVC 1000 interrupt.
211 ROS CRC miscompare during boot.
212 Processor Planar Bad FATAL
213 Memory Card failure or Processor Planar Bad.
214 Power status register failed
215 A low voltage condition is present
216 ROS code being uncompressed into memory.
217 End of boot list encountered.
218 RAM POST testing for 2 MB of good memory
219 RAM POST bit map being generated.
21c L2 Cache not detected as part of systems configuration( 2 second dur.
220 IPL Control Block being initialized.
221 NVRAM CRC comparison error during boot in Normal Mode.
222 Attempting Normal boot from NVRAM Boot List from SIO attached devices
223 Attempting Normal boot from NVRAM Boot List from SCSI attached devices
224 Attempting Normal Mode Boot from 9333 subsytem device
225 Attempting Normal Mode boot from from 7012 DBA Disk
226 Attempting Normal Mode boot from Ethernet
227 Attempting Normal Mode boot from Token Ring
228 Attempting Normal boot using expansion code in NVRAM.
229 Attempting Normal Mode boot but list is empty or no devices are available.
22c Attempting a normal mode IPL from FDDI specified in NVRAM IPL device list.
230 Attempting Normal boot from ROM Boot List.
231 Attempting Normal Mode boot from Ethernet
232 Attempting Normal Mode boot from SIO attached devices
233 Attempting Normal Mode boot from SCSI attached devices
234 Attempting Normal Mode boot from 9333 subsytem device
235 Attempting Normal Mode boot from from 7012 DBA Disk
236 Attempting Normal Mode boot from Ethernet
237 Attempting Normal Mode boot from Token Ring
238 Attempting a Normal-mode restart from Token Ring specified by the user.
239 System failed to boot from the device specified by the user.
23c Attempting a normal mode IPL from FDDI specified in IPL ROM device list.
240 Attempting a Service boot from ROM boot list.
241 Attempting a Normal boot from devices specified in NVRAM boot list
242 Attempting Service Mode boot from SIO attached devices
243 Attempting Service Mode boot from SCSI attached devices
244 Attempting Service Mode boot from 9333 subsytem device
245 Attempting Service Mode boot from from 7012 DBA Disk
246 Attempting Service Mode boot from Ethernet
247 Attempting Service Mode boot from Token Ring
248 Attempting Service boot using expansion code in NVRAM.
249 Attempting Service Mode boot from the NVRAM IPL device list.
24c Attempting a service mode IPL from FDDI specified in NVRAM IPL device list.
250 Attempting a Service boot from adapter feature ROM.
251 Attempting Service Mode boot from Ethernet
252 Attempting Service Mode boot from SIO attached devices
253 Attempting Service Mode boot from SCSI attached devices
254 Attempting Service Mode boot from 9333 subsytem device
255 Attempting Service Mode boot from from 7012 DBA Disk
256 Attempting Service Mode boot from Ethernet
257 Attempting Service Mode boot from Token Ring
258 Attempting Service boot from Token Ring specified by user.
259 Attempting a service mode IPL from FDDI specified by the operator.
25c Attempting a service mode IPL from FDDI specified in IPL ROM device list.
260 ROM attempting to display information on the native console.
261 ROM did not find a native display adapter and information will be displayed on the TTY console.
262 ROM did not detect a keyboard while attempting to display information.
263 Attempting a Normal-mode restart from adapter feature ROM specified in NVRAM device list.
269 Stalled State - cannot boot system end of boot list reached
270 Durandoak Ethernet Adapter (LCE) POST executing.
271 Mouse device and adapter POST executing.
272 Tablet adapter POST executing.
276 San Remo Ethernet adapter POST executing.
277 Auto Token-Ring LANstreamer MC 32 Adapter POST.
278 Video ROM SCAN POST executing.
279 FDDI POST.
280 3COM Ethernet POST
281 Keyboard POST executing.
282 Parallel port POST executing.
283 Serial port POST executing.
284 POWER Gt1 graphics adapter POST executing.
285 POWER Gt3 graphics adapter POST executing.
286 Token Ring adapter POST executing.
287 Ethernet adapter POST executing.
288 Adapter card slots being queried.
289 POWER Gt0 graphics adapter POST executing.
290 Testing I/O planar
291 Standard I/O planar being tested.
292 SCSI or SSA adapter POST executing.
293 Bus attached disk POST executing.
294 TCW SIMM in slot J being tested.
295 Color graphics display adapter POST executing.
296 Family 2 feature adapter ROM POST executing.
297 System model number could not be determined.
298 Attempting a warm IPL.
299 Boot ROM passed control to loaded code.
IPL ROS Flash EPROM Codes (300 -325)
301 Flash Utility ROM test failed or checkstop occurred (irrecoverable).
302 Flash Utility ROM: User prompt, move key to service position in
order to perform an optional Flash Update. LED 302 will only appear
if the Key switch is in secure. This signals the user that a Flash
Update may be initiated by moving the key switch to service. If the
key is moved to service then LED 303 will be displayed which signals
the user to press the reset button to select optional Flash Update.
303 Flash Utility ROM: User prompt, press reset button in order to
perform an optional Flash Update. LED 302 will only appear if the
Key switch is in secure. This signals the user that a Flash Update
may be initiated by moving the key switch to service. If the key is
moved to service then LED 303 will be displayed which signals the
user to press the reset button to select optional Flash Update.
304 Flash Utility ROM IOCC POST Error (irrecoverable).
305 Flash Utility ROM Standard I/O POST running.
306 Flash Utility ROM is attempting IPL from Flash Update media device.
307 Flash Utility ROM system model number does not compare between OCS
and ROM (irrecoverable).
308 Flash Utility ROM: IOCC bad TCW SIMM in being tested.
309 Flash Utility ROM passed control to a Flash Update Boot Image.
311 Flash Utility ROM CRC comparison error (irrecoverable).
312 Flash Utility ROM RAM POST memory configuration error or no memory
found (irrecoverable).
313 Flash Utility ROM RAM POST failure (irrecoverable).
314 Flash Utility ROM Power status register failed (irrecoverable).
315 Flash Utility ROM detected a low voltage condition.
318 Flash Utility ROM RAM POST is looking for good memory.
319 Flash Utility ROM RAM POST bit map is being generated.
322 CRC error on media Flash Image. No Flash Update performed.
323 Current Flash Image is being erased.
324 CRC error on new Flash Image after Update was performed. (Flash
Image is corrupted).
325 Flash Update successful and complete.
326 - 3CC (Reserved)
AIX Event Indicators
Configuration Program Indicators
2E6 Ultra/Wide Differential SCSI adapter being configured
2E7 Config method unable to determine if SCSI adapter type SE or DE type
40c Victory Mini-Support Processor being configured
41c Victory Plug In Adapter Support Processor being Configured.
42c Waiting for Interactive Maintenance Analysis Procedures (IMAPS)request.
43c Configuring Interactive Maintenance Analysis Procedures (IMAPS) connection.
440 9.1GB SE Ultra drive (Mako 68 pin)
440 9.1GB Ultra SCSI Disk Drive being configured
441 18.2GB SE Ultra drive (Mako 68 pin)
441 18.2GB Ultra SCSI Disk Drive being identified or configured
442 9.1GB LVD Ultra drive (Neptune 80 pin)
443 18.2GB LVD Ultra drive (Neptune 80 pin)
444 2-Port Multiprotocol PCI Adapter being identified or configured
444 Cost-reduced Hermosa WAN adapter
447 Emulex LP9000 (Centaur) PCI 64 FCS adapter (Flipper64)
447 PCI 64-bit Fibre Channell Arbitrated Loop Adapter being configured
4c0 4c5 Reserved for Rochester AS4D AIX IOP device driver usage.
500 Querying Standard I/O.
501 Querying card in slot 1.
502 Querying card in slot 2.
503 Querying card in slot 3.
504 Querying card in slot 4.
505 Querying card in slot 5.
506 Querying card in slot 6.
507 Querying card in slot 7.
508 Querying card in slot 8.
509 Configuring ATL L500 library (tower configuration) -- IBM machine 7337-410
510 Starting device configuration.
511 Device configuration completed.
512 Restoring device configuration files from media.
513 Restoring basic operating system installation files from media.
516 Contacting server during network boot
517 Mounting client remote file system during network IPL.
518 Remote mount of the root and /usr filesystems failed during network
boot.
519 Configuring ATL L500 library (rack configuration) --- IBM machine 7337-411
520 Bbus configuration running.
521 /etc/init invoked cfgmgr with invalid options; /etc/init has
been corrupted or incorrectly modified (irrecoverable error).
522 The configuration manager has been invoked with conflicting
options (irrecoverable error).
523 The configuration manager is unable to access the ODM database
(irrecoverable error).
524 The configuration manager is unable to access the config rules
object in the ODM database (irrecoverable error).
525 The configuration manager is unable to get data from a
customized device object in the ODM database (irrecoverable error).
526 The configuration manager is unable to get data from a
customized device driver objet in the ODM database (irrecoverable
error).
527 The configuration manager was invoked with the phase 1 flag;
running phase 1 flag; running phase 1 at this point is not
permitted (irrecoverable error).
528 The configuration manager cannot find sequence rule, or no program
was specified in the ODM database (irrecoverable error).
529 The configuration manager is unable to update ODM data
(irrecoverable error).
530 The program "savebase" returned an error.
531 The configuration manager is unable to access PdAt object class
(irrecoverable error)
532 There is not enough memory to continue (malloc failure);
irrecoverable error.
533 The configuration manager could not find a configure method for
a device.
534 The configuration manager is unable to acquire database lock.
irrecoverable error.
536 The configuration manager encountered more than one sequence rule
specified in the same phase. (irrecoverable error).
537 The configuration manager encountered an error when invoking the
program in the sequence rule.
538 The configuration manager is going to invoke a configuration
method.
539 The configuration method has terminated, and control has returned
to the configuration manager.
540 IP Security (IPSec) kernel extensions being configured during IPL.
541 Configuring ATL L500 DLT7000 drive sled assembly
541 A DLT tape device is being configured
542 Configuring ATL L200 autoloader -- IBM machine 7205-342
543 Configuring ATL L200 DLT7000 drive sled assembly
544 ECP peripheral configure method executing.
545 Parallel port ECP device driver being configured.
546 IPL cannot continue due to error in customised data base.
547 Rebooting after error recovery (LED 546 preceded this LED)
548 Restbase failure.
549 Console could not be configured for the "Copy a System Dump Menu.
550 ATM LAN Emulation device driver being configured.
551 IPL Varyon is running
552 IPL Varyon failed.
553 IPL phase 1 is complete.
554 The boot device could not be opened or read,
or unable to define NFS swap device during network boot.
555 ODM error when trying to varyon the rootvg, or unable
to create an NFS swap device during network boot.
556 Logical Volume Manager encountered error during IPL varyon.
557 The root filesystem will not mount.
558 There is not enough memory to continue the system IPL.
559 Less than 2MB of good memory are available to load the AIX kernel.
560 Unsupported Monitor attached to display adapter.
561 Configuring Target Mode SSA device software.
562 Configuring HIPPI network layer.
565 Configuring the MWAVE subsystem.
566 Configuring Namkan twinax commo card (5250 emulation)
567 Configuring HIPPI device driver (fpdev)
568 Configuring HIPPI device driver (fphip)
569 FCS SCSI Protocol device is being configured
570 Virtual SCSI devices being configured.
571 HIPPI common function device driver being configured.
572 HIPPI IPI-3 master transport driver being configured.
573 HIPPI IPI-3 slave transport driver being configured.
574 HIPPI IPI-3 transport services user interface device driver being configured.
575 IBM 9570 RAID 3 disk array device driver being configured.
576 Vendor Async device driver configuration.
576 Generic async device driver being configured.
577 Generic SCSI device driver being configured.
578 Generic commo device driver being configured.
579 Device driver being configured for a generic device.
580 HIPPI TCPIP network interface driver being configured.
577 Vendor SCSI device driver configuration.
578 Vendor Commo device driver configuration.
579 Configuring a generic vendor device driver configuration.
580 HIPPI TCPIP network interface driver being configured.
581 Configuring TCP/IP.
582 Configuring token ring data link control
583 Configuring ethernet data link control
584 Configuring IEEE ethernet data link control
585 Configuring SDLC MPQP data link control
586 Configuring QLLC X.25 data link control
587 Configuring NETBIOS
588 Configuring a Bisync Read-Write (BSCRW).
589 SCSI target mode device being configured.
590 Diskless remote paging device being configured.
591 Configuring an LVM device driver.
592 Configuring an HFT device driver.
593 Configuring SNA Device Drivers or Configuring LFT.
594 Asynchronous I/O being defined or configured.
595 X.31 pseudo device being configured.
596 SNA DLC/LAPE pseudo device being configured.
597 OCS Software being configured.
598 OCS hosts being configured during system reboot.
599 Configuring FDDI data link control.
59c Tarpon/Shark storage subsystem device driver configuration.
5c0 Streams based hardware driver being configured.
5c1 Streams based X.25 protocol stack being configured.
5c2 Streams based X.25 COMIO emulator driver being configured.
5c3 Streams based X.25 TCP/IP interface driver being configured.
5c4 FCS adapter device driver being configured.
5c5 Pseudo device for IP mapping Network device driver for FCS being configured.
5c5 SCB network device driver for FCS is being configured.
5c6 AIX SNA Channel being installed and configured.
600 Starting network boot portion of /sbin/rc.boot
602 Configuring network parent devices.
603 /usr/lib/methods/defsys, /usr/lib/methods/cfgsys, or
/usr/lib/methods/cfgbus failed.
604 Configuring physical network boot device.
605 Configuration of physical network boot device failed.
606 Running /usr/sbin/ifconfig on logical network boot device.
607 /usr/sbin/ifconfig failed.
608 Attempting to retrieve the client.info file with tftp.
Note that a flashing 608 indicates multiple attempt(s) to
retrieve the client_info file are occurring.
609 The client.info file does not exist or it is zero length.
60B 18.2GB 68-pin LVD SCSI Disk Drive being configured
60C Lochmere 1.4 GB IDE disk drive being configured.
610 Attempting remote mount of NFS file system
611 Remote mount of the NFS filesystem failed.
612 Accessing remote files; unconfiguring network boot device.
614 Configuring local paging devices.
615 Configuring of a local paging device failed.
616 Converting from diskette to dataless configuration.
617 Diskless to dataless configuration failed.
61c Lochmere 2.1 GB IDE disk drive being configured.
618 Configuring remote (NFS) paging devices.
619 Configuration of a remote (NFS) paging device failed.
61B 36.4GB 80-pin LVD SCSI Disk Drive being configured.
61D 36.4GB 80-pin LVD SCSI Disk Drive being configured.
61E 18.2GB 68-pin LVD SCSI Disk Drive being configured.
620 Updating special device files and ODM in permanent filesystem with
data from boot RAM filesystem.
621 9.1 GB LVD 80-pin SCSI Drive being configured.
622 Boot process configuring for operating system installation.
625 Creating directory for local NIM mount points.
626 OEM FC SCSI Disk being configured.
627 FC SCSD SCSI Disk being configured.
628 SCSI SCSD FC CDROM Drive being configured.
629 OEM SCSI FC CDROM Drive being configured.
62c Lochmere 3.0 GB IDE disk drive being configured.
62D 9.1GB 68-pin LVD SCSI Disk Drive being configured.
62E 9.1GB 68-pin LVD SCSI Disk Drive being configured.
630 SCSD FC SCSI Read/Write Optical Drive being configured.
631 OEM FC SCSI Read/Write Optical Drive being configured.
632 25 Mbs Charm 1.5 ATM adapter being configured.
633 155 Mbs Charm 2.1 UTP ATM adapter being configured.
634 155 Mbs Charm 2.1 MMF ATM adapter being configured.
635 155 Mbs Charm 2.1 SMF ATM adapter being configured.
636 622 Mbs Charm 2.5 BigBend ATM adapter being configured
636 TURBOWAYS 622 Mbps PCI MMF ATM Adapter.
637 Aladdin Dual Channel PCI-2 Ultra2 SCSI Adapter being configured.
638 4.5GB Ultra SCSI Single Ended Disk Drive being configured.
639 9.1GB 10K RPM Ultra SCSI Disk Drive (68-pin) being configured.
63A See 62D.
63B 9.1GB 80-pin LVD SCSI Disk Drive being configured.
63C See 60B.
63D 18.2GB 80-pin LVD SCSI Disk Drive being configured.
63E 36.4GB 68-pin LVD SCSI Disk Drive being configured.
63F See 61B.
640 9.1GB 10K RPM Ultra SCSI Disk Drive (80-pin).
641 Draco 9.1 GB 80-pin LVD Ultra 2 SCSI disk being configured.
642 Draco 4.5 GB LVD 80-pin SCA-2 connector SCSI Disk being configured
643 Hammerhead 18.2 GB LVD 80-pin SCA-2 connector SCSI Disk being configured
644 Swordfish 36.4 GB LVD 80-pin SCA-2 connector SCSI Disk being configured
646 High-Speed Token-Ring PCI Adapter being configured.
649 8X Optical Disk drive being configured (Pirahna Tape Library)
64A See 62E.
64B 9.1GB 80-pin LVD SCSI Disk Drive being configured.
64C See 61E.
64D 18.2 GB LVD 80-pin Drive/Carrier being configured.
64E 36.4GB 68-pin LVD SCSI Disk Drive being configured.
64F See 61D.
650 IBM SCSD disk drive being configured.
651 Reserved (Diagnostics)
652 Reserved (Diagnostics)
653 18.2GB Ultra-SCSI 16-bit Disk Drive being configured.
654 Sailfin Jr. 4.5 GB 68 Pin SCSI SE drive being configured.
655 GXT130P (Maui) Graphics adapter being configured.
656 Polar 3 1/4 inch SCSI tape drive being configured.
657 GXT2000P Mirage graphics adapter being configured.
658 Dolphin 2102 disk array controller configuration.
658 PCI Fibre Channel Disk Subsystem Controller being identified or configured.
659 Dolphin 2102 disk array router configuration.
659 2102 Fibre Channel Disk Subsystem Controller Drawer being identified or
configured.
660 Dolphin 2102 Fibre Channel Disk Array being identified or configured.
661 OEM IDE Tape Drive
661 USB host controller configuration.
662 Ultra2 Integrated SCSI controller
662 Smbios 895 based SCSI adapter configuration.
663 The ARTIC960RxD Digital Trunk Quad PCI Adapter or the ARTIC960RxF
Digital Trunk Resource Adapter being configured.
664 Brighton 32X SCSI CDROM drive configuration.
665 Sailfin 9.1 GB 80 pin LVD SCSI disk drive configuration.
666 Marlin 18.2 GB 80 pin LVD SCSI disk drive configuration.
667 PCI 3-Channel Ultra2 Clarinet SCSI RAID Adapter being configured.
668 25 Mbs MCA ATM adapter configuration.
669 PCI Gigabit Ethernet Adapter Galaxy being configured.
66C 10/100/1000 Base-T EthernetPCI Adapter.
66D PCI 4-Channel Ultra-3 SCSI RAID Adapter.
66E 4.7 GB DVD-RAM drive
670 Marlin 18.2 GB SCSI 80 Pin SCA driver configuration.
671 Sailfin 9.1 GB SCSI 80 Pin SCA driver configuration.
672 Sailfin 9.1 GB SCSI differential drive configuration.
673 Marlin 18.1 GB SCSI differential drive configuration.
674 ESCON ® Channel PCI Adapter being configured.
675 ARTIC960Hx PCI adapter being configured.
676 ARTIC960Rp PCI adapter being configured.
677 PCI 32-bit Fibre Channel Arbitrated Loop Adapter being configured.
677 Emulex LP7000 PCI 32 FCS adapter(firefly/superfly+) being configured.
678 Cadenza 12 GB 4mm tape drive being configured.
679 Draco 4.5 GB SCSI disk drive being configured.
67a Emulex LP9000 (Centaur) PCI 64 FCS adapter (Flipper64)
67B PCI Cryptographic Coprocessor being configured.
680 Supermint MCA Graphics Adapter being configured.
681 Sailfin 9.1 GB Single Ended SCSI disk Drive being configured.
682 20x (MAX) SCSI-2 CD-ROM Drive being configured.
682 ALTA 12X - 20X CDROM drive being configured.
683 IBM 2105 Device being configured.
684 RS 422 Concentrator being configured.
685 Sagebrush Graphics adapter being configured.
686 Medina 8-Port Async PCI adapter being configured.
687 Trinity 128-Port Async adapter being configured.
688 SCSI MC-Disk PCMCIA Card reader being configured.
689 Scorpion 4.5GB Ultra SCSI Single Ended Disk Drive being configured.
68C 20 GB 4-mm Tape Drive being configured.
68E POWER GXT6000P PCI Graphics Adapter.
690 Scorpion 9.1GB Ultra SCSI Single Ended Disk Drive being configured.
691 Turboway 25 Mbs PCI ATM adapter being configured.
692 7205-311 30 GB DLT Tape (Bullhead) drive being configure.
693 ISDN PCI Basic Rate adapter being configured.
694 ISDN MCA Basic Rate adapter being configured.
695 X.25 PCI Coprocessor adapter being configured.
696 Lumbee (Meerkat) 8 MB SM fiber adapter being configured.
697 Lumbee (Gemini- lite) 1 MB MM fiber adapter being configured.
698 Lumbee (Orbitor) 1 MB UTP fiber adapter being configured.
699 Candlestick Park (10/100 Mbs Ethernet adapter being configured.
69b 64-bit/66MHz PCI ATM 155 MMF PCI adapter being configured.
69d 64-bit/66MHz PCI ATM 155 UTP PCI adapter being configured.
6c8 Lochmere Display device driver being configured.
6cc SSA disk drive being configured.
700 Starfire 1.1 GB 8 Bit SCSI Disk being configured.
701 Starfire 1.1 GB 16 Bit SCSI Disk being configured.
702 Starfire 1.1 GB 16 Bit Differential Disk being configured.
703 Starfire 2.2 GB 8 Bit SCSI Disk being configured.
704 Starfire 2.2 GB 16 Bit SCSI Disk being configured.
705 The configuration method for the 2.2GB 16-bit differential SCSI
disk drive is being run. If a irrecoverable error occurs, the
system halts.
705 Starfire 2.2 GB 16 Bit Differential SCSI Diff Disk being configured.
706 Starfire 4.5 GB 16 Bit SCSI Disk being configured.
707 Starfire 4.5 GB 16 Bit Differential Disk being configured.
708 L2 Cache being configured.
709 Frio ISA 128 port async adapter being configured.
70c 270 MB SCSI disk drive (Sandalfoot - Satsuma 1) being configured.
710 POWER GXT150M Neptune graphics adapter being identified/configured.
711 Unknown adapter being identified or configured.
712 Graphics slot bus configuration is executing.
713 Artic 960 adapter being identified/configured
714 Sunrise Video Capture Adapter being identified/configured
715 Fox Club Ultimedia Services audio adapter is being configured. This LED
displays briefly on the panel.
716 Pegasus system memory
717 Durandoak ethernet adapter being configured.
718 GXT 500 display adapter (Magenta)
71c 340 MB SCSI disk drive (Sandalfoot - Conner) being configured.
720 Unknown Read/Write optical drive being identified/configured.
721 Unknown Disk being identified/configured.
721 Unknown SCSI device being identified/configured.
722 Unknown Disk being identified/configured.
723 Unknown CDROM being identified/configured.
724 Unknown Tape being identified/configured.
725 Unknown Display being identified/configured.
726 Unknown Input device being identified/configured.
727 Unknown Async device being identified/configured.
728 Parallel Printer being identified/configured.
729 Unknown Parallel device being identified/configured.
72c 540 MB SCSI disk drive (Sandalfoot - Maxtor) being configured.
730 Unknown diskette drive type being identified/configured.
731 PTY being identified/configured.
732 Unknown SCSI initiator type being configured.
733 Timberwolf 7GB 8mm tape drive being configured.
734 Nueces 4x SCSI-2 640MB CD-ROM Drive
735 Satsuma 540 MB SCSD SCSI disk drive being configured.
736 Quiet Touch keyboard and speaker cable being configured.
736 PS/2 Woodfield keyboard being configured.
737 Woodfield 540 MB SCSI Disk being configured.
738 Woodfield 810 MB SCSI disk being configured.
739 Woodfield CDROM drive being configured.
73c 540 MB SCSI disk drive (Sandalfoot - Quantum) being configured.
740 Pegasus 540 MB SCSI disk drive being configured.
741 Pegasus 1080 MB SCSI disk drive being configured.
742 Klickitat PCI Ethernet adapter being configured.
743 IsoFDDI adapter being identified/configured.
744 Carrera Power Management chip being configured.
745 Andante Tape Autoloader 16GB 4mm being configured.
746 SCSI-2 FW PCI Adapter being configured.
747 SCSI-2 Differential FW PCI Adapter being configured.
748 MCA/CHRP systems keyboard/mouse adapter being configured.
749 Timberwolf 7331-205 Tape library being configured
74c ISA bus Token Ring Adapter (Sandalfoot) being configured.
750 Skyline Token Ring adapter being configured.
751 Copperhead SCSI 32-bit SE F/W RAID Adapter being configured.
752 OEM IDE Disk Drive being configured.
753 OEM IDE CD ROM Drive being configured.
754 1.1GB 16-bit SCSI disk drive being configured
755 2.2GB 16-bit SCSI disk drive being configured
756 4.5GB 16-bit SCSI disk drive being configured
757 Telemark External 13GB 1.5M/s 1/4 inch tape drive being configured
758 Aladdin 540 MB SCSI Drive being configured.
759 PC Co. Pegasus 1080 MB SCSI disk being configured.
75c ISA bus Ethernet Adapter (Sandalfoot) being configured.
760 SCSI adapter function of LSA card being configured.
761 Ethernet adapter function of LSA card being configured.
762 SP: Configuration is running for the TB3 SP switch adapter card
763 SP Switch TB3 MX Adapter being configured.
764 SP System Attachment Adapter TB3 being configured.
765 Reserved - PowerParallel system MCA adapter
766 Reserved - PowerParallel system MCA adapter
767 Reserved - PowerParallel system Hi performance Switch (HPS)
768 Reserved - PowerParallel system HPS
769 Reserved - PowerParallel system HPS
76c Sandalfoot 730 MB Satsuma SCSI drive being configured.
770 Reserved - PowerParallel system HPS
771 Reserved - PowerParallel system HPS
772 4.5GB SCSI F/W Disk Drive
773 9.1GB SCSI F/W Disk Drive
774 9.1GB External SCSI Disk Drive being configured.
775 Cobalt Graphics adapter being configured.
776 PCI Token-Ring Adapter Cricketstick being identified/configured.
777 Phoenix 10/100 Ethernet Tx PCI Adapter being identified or configured.
778 Sierra GXT3000P 3D PCI Graphics adapter being configured.
779 Mercury 3D PCI Graphics Adapter
77a Enhanced Mirage (GXT2200P) FFC=2824 being configured
77b Clover 4-port 10/100 Ethernet Adapter being configured
77c 1GB 16-bit SCSI disk drive being identified/configured.
780 C1X ISA X25 Adapter
781 Gale SDLC ISA Adapter
782 Quantum Fireball 1.2GB hardfile being configured.
783 Hidalgo 4mm DDS-2 Tape Autoloader being configured.
784 Orion 2160 MB SCSI Disk drive being configured.
785 San Gabriel ISA 8 Port EIA 232/RS 422 Adapter
786 GXT250P/GXT255P(Skyblue) graphic adapters being configured.
787 GXT500P/GXT550P (Mint) graphics adapter being configured.
788 Stream Video Capture card being configured.
789 Brewster 2.6GB External Optical Drive being configured
78B Sonora Lite GXT4000P PCI Graphics Adapter being configured.
78C PCI bus configuration executing.
78D GXT300P 2D Graphics adapter being configured.
790 Multi-bus Integrated Ethernet Adapter being identified/configured.
791 Blanco 2.2 GB SCSI Disk Drive being Configured
792 Blanco 4.5 GB SCSI Disk Drive being Configured
793 Blanco 9.1 GB SCSI Disk Drive being Configured
794 San Remo 100 Mbps MCA Ethernet adapter being configured.
795 Honeycomb PCI FDDI adapter being configured.
796 Honeycomb MCA FDDI adapter being configured.
797 Turboways 155 UTP/STP ATM Adapter being identified/configured
798 Turboway 155 MPEG ATM adapter being configured.
798 Video streamer being identified or configured
799 Hermosa 2-Port Multiprotocol PCI adapter being identified/configured.
79c ISA bus configuration executing.
7C0 CPU/System Interface being configured.
7C1 Business Audio Subsystem being identified/configured.
7c2 Starfire 1.1 GB 16B SCSI SE Disk drive with Allthorn Carrier
7c3 Sandalfoot Spitfire 1 GB 8B SCSI SE disk drive being configured.
7c4 Starfire 2.2 GB 16B SE disk drive with Allthorn carrier.
7c5 Presto 810 MB SCSI Disk being configured.
7c6 Starfire 4.4 GB 16B SE disk drive with Allthorn carrier.
7c7 Woodfield display device driver being configured
7c8 Woodfield video capture/playback device driver being configured.
7c9 Presto 1.2 GB SCSI Disk being configured.
7cc PCMCIA bus configuration executing.
800 Turboways 155 MMF ATM Adapter being identified/configured
801 Reserved (Diagnostics)
802 Reserved (Diagnostics)
803 7336 Tape Library Robotics being configured
804 ASPEN 8x CDROM Drive SCSI-2 being configured
806 GXT800 (Supermint) PCI Graphics adapter being configured.
807 SCSI Device Enclosure being configured.
808 Pegasus SIF (System Interface Full) configuration process
809 Reserved (Diagnostics)
80c Mayflower SSA 4-Port Adapter being indentified or configured
810 Reserved (Diagnostics)
811 Processor Complex being identified/configured.
812 Memory being identified or configured.
813 Battery for time-of-day, NVRAM, and so on being identified/ configured, or
system I/O Control Logic being identified/ configured.
814 NVRAM being identified/configured.
815 Floating Point Processor being identified/configured.
816 Operator Panel Logic being identified/configured.
817 Time of Day Logic being identified/configured.
818 Reserved (diagnostics)
819 Graphics Input Device Adapter being identified/configured.
81c S3 928 PCI graphics adapter being configured.
820 Interprocessor related testing
821 Standard Keyboard adapter being identified/configured.
823 Standard Mouse adapter being identified/configured.
824 Standard Tablet adapter being identified/configured.
825 Standard Speaker adapter being identified/configured.
826 Serial Port 1 adapter being identified/configured.
827 Parallel port adapter being identified/configured.
828 Standard Diskette Adapter being identified/configured.
829 Lumbee PCI ATM adapter being configured.
82c Weitek P9000 PCI graphics adapter being configured.
830 Creek 8-Port ISA Async Adapter
831 IBM3151 adapter being identified or configured, or Serial Port 2
being identified or configured.
832 Reserved (Diagnostics)
833 Reserved (Diagnostics)
834 64-Port Async Controller being identified/configured.
835 16-Port Async Concentrator being identified/configured.
836 128-Port Asynchronous Controller
837 16-port RAN, 16-EIA-232 being identified or configured.
838 Bitternut Network Terminal Accelerator adapter being identified/configured.
839 Bitternut 7318 Serial Communication Server being configured.
83c SP2 High Performance Switch (HPS) being configured.
840 PCI Single-Ended Ultra SCSI Adapter being configured.
841 8-Port Async Adapter (EIA-232) being identified/configured.
842 8-Port Async Adapter (EIA-422A) being identified/configured.
843 8-Port Async Adapter (MIL-STD 188) being identified/configured.
844 Allthorn 7135 RAIDiant Array disk drive subsystem drawer being identified
845 7135 RAIDiant Array disk drive subsystem drawer being identified or
configured.
846 RAIDiant Array SCSI 1.3GB Disk Drive
847 16-Port Serial Adapter (EIA-232) being identified/configured.
848 16-Port Serial Adapter (EIA-422) being identified/configured.
849 X.25 Communications Adapter being identified/configured.
84c Slimline CD ROM Drive (Sandalfoot) being configured.
850 Token-Ring Network adapter being identified/configured.
851 T1/J1 Portmaster adapter being identified or configured.
852 Ethernet adapter being identified/configured.
853 SCSI D I/O controller being identified/configured.
854 3270 Connection being identified/configured.
855 4-port multiprotocol adapter being identified or configured.
856 POWER RADIANT device driver being configured
857 FSLA adapter being identified/configured.
858 5085/86/88 adapter being identified/configured.
859 FDDI adapter being identified/configured.
85c Wildwood Token-Ring High-Performance LAN adapter being identfied/configured.
860 Twin Tail adapter being identified/configured.
861 Optical adapter being identified/configured.
862 Block multiplexer channel adapter being identified/configured.
863 MAP adapter being configured.
864 Serial Channel adapter being identified/configured.
865 370 Serial Channel adapter being identified/configured
866 SCSI Adapter being identified/configured.
867 Async Expansion adapter being identified/configured.
868 SCSI Adapter being identified/configured.
869 SCSI Adapter being identified/configured.
86c 270 MB SCSI disk drive (Sandalfoot - Quantum) being configured.
870 Serial Disk Drive Adapter being identified/configured.
871 Graphics Subsystem Adapter being identified/configured.
872 Grayscale Graphics adapter being identified/configured.
873 Skyway 16 adapter being identified/configured.
874 Color Graphics adapter being identified/configured.
875 Vendor generic type communication adapter being configured.
876 8-Bit Color Graphics Processor being identified/configured.
877 POWER Gt3/Gt4 being identified or configured.
878 GT4 Graphics adapter being identified/configured.
879 24-bit Color Graphics Processor MEV2 being identified/configured
87c 360 MB SCSI disk drive (Sandalfoot - Satsuma 2) being configured.
880 POWER Gt1 graphics adapter being identified/configured.
881 Channel Attached Printer Adapter
882 Serial Attached Printer Adapter
883 Japan Pegasus support.
884 3117 Scanner Adapter
885 3118 Scanner Adapter
886 3119 Scanner Adapter
887 Integrated ethernet adapter being identified/configured.
888 Reserved
889 SCSI adapter being identified or configured.
88c 540 MB SCSI disk drive (Sandalfoot - Satsuma 3) being configured.
890 Corvette SCSI-2 DE/FW and SE/FW adapter being configured.
891 Vendor SCSI adapter being identified/configured.
892 Vendor Display adapter being identified/configured.
893 Vendor LAN adapter being identified/configured.
894 Vendor Async/Communications adapter being identified/configured.
895 Vendor IEEE 488 adapter being identified/configured.
896 Vendor VME Bus adapter being identified/configured.
897 S/370 Channel Emulator Adapter being identified or configured.
898 White Oak GT1X graphics adapter being identified or configured
899 Yuma/Calva 3490 attached tape drive being identified or configured
89c Bandera multimedia SCSI CD-ROM is being identfied/configured.
8c0 Coral chip IDE ports being configured.
8c1 Exabyte 2502 IDE tape drive being configured.
8c2 IDE CD-ROM XA 2x being configured.
8c3 270 MB IDE disk drive being configured.
8c4 360 MB IDE disk drive being configured.
8c5 540 MB IDE disk drive being configured.
8c6 720 MB IDE disk drive being configured.
8c7 1 GB IDE disk drive being configured.
8cc WDC AC1270F 270 MB IDE disk being configured
900 Brushy GXT110P Graphics Adapter being identified/configured.
901 Vendor SCSI device being identified/configured.
902 Vendor Display being identified/configured.
903 Vendor Async device being identified/configured.
904 Vendor Parallel device being identified/configured.
905 Vendor other adapter type being configured.
906 IBM Premier Speech Recognition adapter I being configured.
907 IBM Premier Speech Recognition adapter II being configured.
908 Ruby GXT1000 graphics subsystem being identified/configured
909 PEGASUS LSA (LAN SCSI/ADAPTER) being configured.
90c DALA-3420 420 MB IDE disk being configured.
910 1/4GB Fibre Channel/266 Standard Adapter being indetified or configured
911 Fibre/Channel/1063 Adapter Short Wave.
912 2GB SCSI-2 differential tape drive being identified/configured
913 1GB SCSI-2 differential tape drive being identified/configured
914 5GB 8mm differential tape drive being identified/configured
915 Rhapsody 4GB 4mm SCSI Tape drive being identified/configured.
916 Non-SCSI vendor tape adapter being identified or configured
917 2.4GB 16-bit DE SCSI disk drive being identified/configured
918 2.4GB 16-bit SE SCSI disk drive being identified/configured
919 Multimedia Audio adapter being identified/configured.
91c Sandalfoot 4mm 2GB tape drive being configured.
920 Bridge box being identified or configured
921 Keyboard 101 being identified/configured.
922 Keyboard 102 being identified/configured.
923 Keyboard Kanji being identified/configured.
924 2-Button Mouse being identified/configured.
925 3-Button Mouse being identified/configured.
926 Tablet 5083 Model 21 being identified/configured.
927 Tablet 5083 Model 22 being identified or configured
928 Standard speaker being identified or configured
929 Dials being identified or configured
930 Lighted Program Function Keys(LPFK) being identified or
configured
927 Tablet 5083 Model 22 being identified/configured.
928 Standard Speaker being identified/configured.
929 Dials being identified/configured.
92c DALA-3540 540 MB IDE disk being configured.
930 Lighted Program Function Keys (LPF) keyboard being
931 IP router being identified or configured
933 Async Planar being identified/configured.
934 Async Expansion Drawer being identified/configured.
935 2 MB 3.5-Inch Diskette Drive being identified/configured.
936 5.25-Inch Diskette drive being identified/configured.
937 HIPPI adapter (Torch) being configured.
938 (Yukon) Serial HIPPI PCI adapter being configured.
939 Reserved (Diagnostics)
93c DPEA-30540 540 MB IDE disk being configured.
940 Reserved ( Diagnostics)
942 Baby Blue GXT100 graphics adapter being identified/configured
943 3480 and 3490 control units attached to a System/370 Channel Emulator/A
adapter are identified/configured.
944 100MB ATM adapter being configured
945 Spitfire 1 GB 16 Bit DE drive being identified/configured.
946 Serial port 3 adapter is being identified or configured.
947 Satsuma730MB SCSI disk drive is being configured.
948 Portable disk drive being identified or configured
949 Unknown Bus Attached Disk Drive being identified/configured.
94c WDC AC2540H 540 MB IDE disk being configured.
950 Missing SCSI device being identified or configured
951 670 MB SCSI Disk Drive being identified/configured.
952 355 MB SCSI Disk Drive being identified/configured.
953 320 MB SCSI Disk Drive being identified/configured.
954 400 MB SCSI Disk Drive being identified/configured.
955 857 MB SCSI Disk Drive being identified/configured.
956 670 MB SCSI Disk Drive being identified/configured.
957 120 MB Direct Bus Attached Disk Drive being identified/configured.
958 160 MB Direct Bus Attached Disk Drive being identified/configured.
959 160 MB SCSI Disk Drive being identified/configured.
95c WDC AC2700H 730 MB IDE disk being configured.
960 1.37GB SCSI disk drive being identified/configured.
961 Route 66 2 Port Serial Adapter being configured.
962 Route 66 Ethernet Adapter being configured.
964 Mammoth 20 GB 8mm tape drive being configured
965 Route 66 Token Ring Adapter being configured.
966 Digital to Analog Video Decoder Adapter being configured.
967 Peermaster (Xpoint) Ethernet adapter being configured.
968 1.0GB 3.5" SCSI disk drive being identified or configured.
969 Reserved (Diagnostics)
96c DPEA-30810 810 MB IDE disk being configured.
970 0.5-Inch 9-Track Tape drive being identified/configured.
971 150 MB .25-Inch Tape drive being identified/configured.
972 8mm SCSI Tape drive being identified/configured.
973 Other SCSI Tape drive being identified/configured.
974 CDROM drive being identified/configured.
975 ERIMO optical disk drive is being identified/configured.
976 RISC System/6000 SCSI I/O Controller Initiator
977 M-Audio capture and playback adapter being identified/configured.
978 IEEE 4888 Adapter being identified/configured.
979 7246 SBS Frame Buffer Adapter being configured.
97c DPEA-301080 1080 MB IDE disk drive being configured.
980 TBO - IBM Switching network interface adapter being configured.
981 540MB SCSI-2 disk drive being identified or configured.
982 Graphics Visualization Server Adapter
983 XGA grapphics adapter being identified/configured.
984 1GB 8-bit disk drive being identified/configured.
985 M-Video capture and playback adapter being identified or configured.
986 2.4 GB SCSI Disk Drive being identified/configured.
987 Enhanced SCSI CD-ROM drive is being identified/configured.
988 KILLY FDDI adapter being configured.
989 200 MB SCSI Disk Drive being identified/configured.
98c WDC AC31000H 1083 MB IDE disk being configured.
990 2.0 GB SCSI Disk Drive being identified/configured.
991 525 MB 1/4 inch SCSI Tape being identified/configured.
992 4755 Crytographic adapter being configured.
993 Raven File Server product being configured.
994 5 GB 8mm Tape Drive being identified/configured
995 1.2GB 1/4-Inch tape drive being identified/configured.
996 MP/A adapter being configured.
997 Twisted pair FDDI adapter being identify/configured.
998 2GB 4mm tape drive being identified/configured.
999 7137 or 3514 Disk Array Subsystem being identified/configured
99c 2 GB SCSI Disk drive being configured.
D46 Token-Ring Cable
D50 SCSI Device/SCSI Cable/SCSI Terminator
D81 T2 Ethernet Adapter II being configured
2530 10/100 Mbps Ethernet PCI Adapter being configured
___________________________________________________________________________
| Valid Power Failure Codes | |
|________________________________| Type of Failure |
| Digit 1 | Digit 2 | Digit 3 | |
|__________|__________|__________|__________________________________________|
| blank | blank | blank | No |
| 8 | | | Fan P49B. |
| 4 | | | Fan P49C. |
| u | | | = Digit 1 Codes 8 and 4. |
| | 8 | | Fan at P47. |
| | 4 | | Fan P46A or P46 or both. |
| | 2 | | Fan P49A. |
| | 6 | | = Digit 2 Codes 4 and 2. |
| | c | | = Digit 2 codes 8 and 2. |
| | u | | = Digit 2 codes 8 and 4. |
| |Inverted F| | = Digit 2 codes 8, 4 and 2. |
| | | 8 | Excessive temperature in power supply. |
| | | 4 | Power failure in power supply. |
| | | 2 | Power failure outside power supply. |
| | | 1 | Loss of primary power. |
|__________|__________|__________|__________________________________________|
CHRP Version 3 logs ELA Source Numbers
A00 - A1F CHRP Version 3 ELA
A20 - AFF Reserved
Diagnostics Load Progress Indicators
c00 AIX Install/Maintenance loaded successfully.
c01 Insert the first diagnostic diskette.
c02 Diskettes inserted out of sequence.
c03 The wrong diskette is in diskette drive.
c04 The loading stopped with a nonrecoverable error.
c05 A diskette error occurred.
c06 The rc.boot configuration shell script is unable to determine
type of boot.
c07 Insert the next diagnostic diskette.
c08 RAM file system started incorrectly.
c09 The diskette drive is reading or writing a diskette.
Kernel Debugger Codes
c20 An unexpected halt occurred, and the system is configured to enter
the kernel debug program instead of entering a system dump.
Boot and Install Codes
c21 The ifconfig command was unable to configure the network
for the client network host.
c22 The tftp command was unable to read client's
ClientHostName info file during a client network boot.
c24 Unable to read client's ClientHostName.info
file during a client network boot.
c25 Client did not mount remote miniroot during network install.
c26 Client did not mount the /usr file system during the network boot.
c29 The system was unable to configure the network device.
Console
c31 Select the console display for the diagnostics. To select No console
display, set the key mode switch to Normal then to Service. The
diagnostic programs will then load and run the diagnostics
automatically.
c32 A direct-attached display (HFT/LFT) was selected.
c33 A tty terminal attached to serial ports S1 or S2 was selected.
c34 A file was selected. The console messages store in a file.
c35 No Console Found
BOS Install Codes
c40 Configuration files are being restored.
c41 Could not determine the boot type or device.
c42 Extracting data files from diskette.
c43 Cannot access the boot/install tape.
c44 Initializing installation database with target disk information.
c45 Cannot configure the console.
c46 Normal installation processing.
c47 Could not create a physical volume identifier (PVID) on disk.
c48 Prompting you for input.
c49 Could not create or form the JFS log.
c50 Creating root volume group on target disks.
c51 No paging devices were found.
c52 Changing from RAM environment to disk environment.
c53 Not enough space in the /tmp directory to do a preservation installation.
c54 Installing either BOS or additional packages.
c55 Could not remove the specified logical volume in a preservation installation.
c56 Running user-defined customization.
c57 Failure to restore BOS.
c58 Displaying message to turn the key.
c59 Could not copy either device special files, device ODM, or volume
group information from RAM to disk.
c61 Failed to create the boot image.
c62 Loading platform dependent debug files.
c63 Loading platform dependent data files
c64 Failed to load platform dependent data files
Diagnostic Codes
c70 Problem Mounting diagnostic CDROM disc
c99 Diagnostics have completed. This code is only used when there is
no console.
Fxx Fxx, (xx is any character) - Victory Firmware usage.