128-Port Asynchronous Controller ISA
Type 3-9 #2933
Fileset: devices.isa.cxia128.* 1. install devices.isa.cxia128 2. if smit fails to configure the adapter, apply IX55876 or try: mkdev -tcxia -cadapter -sisa -pbus1 -a bus_io_addr=0x328 make sure the addr switch matches the given addr _______ ______ _______ _______ _ | Node1 | |Node2 | | Node3 | | Node4 | __________________| |_______| |______| |_______| |_______| | 73H3384 | | |_______| |________| |________| | |(11H9536)Type 3-9 |1__NB/NC__| NB/NC NB/NC NB/NC T | 128-Port #2933 |2___ND____ |______ __| | ___ND______ ___ND______ ___ND______ |||||||||| | __|_|__ __|_|__ __|_|__ __|_T__ | Node1 | | Node2 | | Node3 | | Node4 | |_______| |_______| |_______| |_______| ----------- ----------- ----------- ------------------------------ | Cables | P/N | Length | | Terminator HD-15 (Wrap plug) | ----------- ----------- ----------- ------------------------------ | NC 8-wire | 43G0936 | 0.75ft | | | | NB 8-wire | 43G0937 | 15 ft | | 43G0938 (pair) | | ND 4-wire | No IBM PN | See Cable | | 43G0928 (one) | ----------- ----------- ----------- ------------------------------ ______________________________ | | | Address Switches | |______________________________| | Hex | | | | | | Addr | 1 | 2 | 3 | 4 | |______|_____|_____|_____|_____| | 108 | Off | Off | On | On | | _____|_____|_____|_____|_____| | 118 | Off | On | Off | On | | _____|_____|_____|_____|_____| | 128 | Off | On | On | On | | _____|_____|_____|_____|_____| | 208 | On | Off | Off | On | | _____|_____|_____|_____|_____| | 228 | On | Off | On | On | | _____|_____|_____|_____|_____| | 308 | On | On | Off | On | |______|_____|_____|_____|_____| | 328 | On | On | On | On | |______|_____|_____|_____|_____| __________________ _____ | 128-Port adapter |____NE___|Modem|______ _ | |ţ |_____| | |_______ _| | __ ____ ||||||||_| _____ _ _ _ _ _ _ | |_|_ | | _____ | |____| | |__|ModemĂ______NB/NC____| Node1 | |_____| |_T__ |____| Node2 4-Wire cabling cannot be used with synchronous modems or 8-Wire on same controller line. Remote Async Node 16-Port EIA-232 FFC837 PN51G8139 #8130 FFC837 ___________________________________________________________________ | _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ | | |#| |_| |_| |_| |_| |_| |#| |_| |_| |_| |_| |_| |_| |_| |_| |#| | | | 1 2 3 4 5 | 7 8 9 10 11 12 13 14 |15 | |___|_______________________|___________________________________|___| NK| NL| |NM | |___ Terminal/Printer | |_ ____D____ E Device Modem ___| RANs: RAN 16-Port EIA-232 FFC 837 P/N 88G3842 #8130 1.2 Mbps ( Rack Mount) RAN 16-Port EIA-232 FFC 837 P/N 40H2589 #8136 1.2 Mbps Enhanced RAN 16-Port EIA-232 FFC 837 P/N 93H6549 #8137 2.4 Mbps EIA-422 93H6563 #8138 2.4 Mbps TRANSFORMERs: NOTE: All former non-removable FRU now sub to the removable 93H7091 If you replace a non-removable with a removable, also order power cord 6952300 Current 93H7091, 88G2749--+-51G8528, 51G8527, 43G0934. 110-250V (Power cord removable) | +-51G8526, 43G0933. 115-127V (Power cord non-removable) - MCA adapter does NOT support enhanced ran. - Enhanced RAN required AIX 4.2.1 or 4.3. - Enhanced Ran and non-enhanced RAN can be mixed but they will run at the slower speed ( 1.2Mbps not 2.4Mbps ).. _______________________________________________________________ | Cables | P/N | Length | | |__________|___________________|__________|_____________________| | NK | 51G8610 (qty 4) | 9 Inches | Converter RJ45-DB25 | | | (43G0935) | | | |__________|___________________|__________|_____________________| | NL | Customer Supplied | | Terminal/Printer | | NM | Customer Supplied | | Modem | |__________|___________________|__________|_____________________| Programming the RAN __________________________________________________________________________ | _______ ____ ____ | | TD RD RTS CTS DSR CD DTR RI OFS IFC | _ | | | | | | | O O O O O O O O O O | |_| | | | // | | \\ | | | | | | | | \\ | | // | | | |_______| |____| |____| | |__________________________________________________________________________| - Power-on the RAN. P0 is display during POST - When the POST is complete, P1 appears and the RAN is ready for the following programming steps. - Press the LEFT ARROW to enter programming mode. The current NODE NUMBER (1n, 2n,3n or 4n) is displayed - Press the RIGHT ARROW repeatedly until the desired NODE NUMBER is displayed. - Press the left arrow to select the node number entered in the previous step. Pn will appear momentarily, meaning that the node has been successfully programmed. The display then return to P1 and awaits microcode download from the controller. - AC indicate that IPL is complete and RAN is ready. En error in RAN If En appears, the RAN has been improperly programmed in one of the following way. - The RANs have not been programmed in ascending order. That is, the RAN displaying the En has been programmed to a lower number than the preceeding RAN. - Two or more RAN have been programmed assigned the same number. The RAN displaying the En has been programmed to the same number as another node on the same controller line. NOTE: Node number should be assigned in ascending order on each controller line. The RAN closest to the controller being 1n, the second RAN 2n and so on. Numbers greater than 4 will not configured. RAN IN and OUT connectors ________________________________________ IN Connector | Pin Number | Signal Name | 1 5 |__IN___OUT__|___________________________| __|_______________|__ | 1 6 | TD- | Transmit Data - | | . . . . . | | 2 7 | TD+ | Transmit Data + | 6_____ . . . . .____10 | 3 15 | RTS+ | Request to Send + | \ . . . . . / | 4 9 | TC- | Transmit Clock - | \|_______________|/ | 5 10 | TC+ | Transmit Clock + | 11 15 | 6 1 | RD- | Receive Data - | | 7 2 | RD+ | Receive Data + | OUT/T Connector | 8 14 | RTS- | Request To Send - | 5 1 | 9 4 | RC- | Receive Clock - | __|_______________|__ | 10 5 | RC+ | Receive Clock + | | o o o o o | | 11 11 | | Not used | 10_____ o o o o o____6 | 12 12 | S GND | Signal Ground | \ o o o o o / | 13 13 | +5 | +5 Volts | \|_______________|/ | 14 8 | CTS- | Clear To Send - | 15 11 | 15 3 | CTS+ | Clear To Send + | |____________|_______|___________________| Baud Rate VS Length ____________________________________ | Controller Line | Total Controller | The controller line length | Baud Rate | Cable Length | is the actual cable length |_________________|__________________| from the controller to the | Bps | meters feet | last REmote Async Node in | 2400 | 1200 3930 | the controler line. | 4800 | 1200 3930 | | 9600 | 1200 3930 | | 19200 | 1200 3930 | | 38400 | 1200 3930 | | 57600 | 1200 3930 | | 76800 | 1200 3930 | | 115000 | 900 2950 | | 230000 | 400 1350 | | 460000 | 300 1000 | | 920000 | 300 1000 | |1200000 | 300 1000 | |_________________|__________________| Location Code Format for 128-Port Async Subsystem AB-CD-EF-GH || || || || || || || ||_____ Async port number || || || || || ||________ Remote async node 1 through 4 || || | || || |_________ Adapter connector 1 or 2 || || || ||___________ Adapter slot number || | || |____________ I/O bus number || ||______________ Always 00 O u t s t a n d i n g i n t h e f i e l d !
Updated Jan 2003 Bruno Croft

128-Port Asynchronous Controller ISA Type 3-9 #2933

128-Port Asynchronous Controller ISA
Type 3-9 #2933