The Microcode files provided in this package are only for use when installing disk drive microcode to a disk drive installed in a pSeries Server using the AIX or Linux Operating System.

1.1 Disk Drives Affected

Below is the list of microcode files in this package, these files are for use with the following pSeries SCSI hard disk drive ONLY:

NOTE: To insure the integrity of microcode files, please check the checksum value of each file after extraction

Size     Disk Drive Model        FRU#       P/N (VPD)         Microcode File Name                 Checksum         Comment
--------    ---------------------   -----------      -------------       -------------------------------------       ----------      -----------------------------------------
9GB       ST373455LW         80P3148     80P3148         ST37345.54493030.43383044        16582        (68 pin-Bare)

9GB ST373455LC 09P3921 09P3917 ST37345.54493030.43383044 16582 (80 pin-U320 Carrier)

18GB ST373455LW 80P3149 80P3149 ST37345.54493030.43383041 16582 (68 pin-Bare)

18GB ST373455LC 00P3829 00P3829 ST37345.54493030.43383044 16582 (80 pin-U320 Carrier)

18GB ST373455LC 09P3823 09P3822 ST37345.54493030.43383044 16582 (80 pin-pScallop)

18GB ST373455LC 80P3150 80P3150 ST37345.54493030.43383044 16582 (80 pin-Mill)

36GB ST373455LW 80P3151 80P3151 ST37345.54493030.43383044 16582 (68 pin-Bare)

36GB ST373455LC 80P3152 80P3152 ST37345.54493030.43383044 16582 (80 pin-Bare)

36GB ST373455LC 00P3831 00P3830 ST37345.54493030.43383044 16582 (80 pin-U320 Carrier)

36GB ST373455LC 80P6319 80P6478 ST37345.54493030.43383044 16582 (80 pin-U320-HV)

36GB ST373455LC 09P3826 09P3825 ST37345.54493030.43383044 16582 (80 pin-pScallop)

36GB ST373455LC 03N6340 03N6339 ST37345.54493030.43383044 16582 (80 pin-U320 Carrier)

36GB ST373455LC 03N6342 03N6341 ST37345.54493030.43383044 16582 (80 pin-U320-HV)

36GB ST373455LC 00P2697 00P5262 ST37345.54493030.43383044 16582 (80 pin-Scallop Carrier)

73GB ST373455LC 03N6345 03N6344 ST37345.54493030.43383044 16582 (80 pin-U320 Carrier)

73GB ST373455LC 03N6347 03N6346 ST37345.54493030.43383044 16582 (80 pin-U320-HV)

73GB ST373455LC 00P2689 00P5264 ST37345.54493030.43383044 16582 (80 pin-pScallop Carrier)

73GB ST373455LC 10N7194 10N7221 ST37345.54493030.43383044 16582 (68 pin-Bare)

73GB ST373455LW 80P3153 80P3153 ST37345.54493030.43383044 16582 (68 pin-Bare)

73GB ST373455LW 03N5255 03N5255 ST37345.54493030.43383044 16582 (68 pin-Bare)

73GB ST373455LC 80P3154 80P3154 ST37345.54493030.43383044 16582 (80 pin-Mill Carrier)

73GB ST373455LC 03N6325 03N6324 ST37345.54493030.43383044 16582 (80 pin-U320 Carrier)

73GB ST373455LC 03N6327 03N6326 ST37345.54493030.43383044 16582 (80 pin-U320-HV)

73GB ST373455LC 09P3928 09P4343 ST37345.54493030.43383044 16582 (80 pin-pScallop)

146GB ST3146855LW 03N5256 03N5256 ST31468.54493030.43383044 16582 (68 pin-Bare)

146GB ST3146855LC 03N6330 03N6329 ST31468.54493030.43383044 16582 (80 pin-U320 Carrier)

146GB ST3146855LC 03N6332 03N6331 ST31468.54493030.43383044 16582 (80 pin-U320-HV)

146GB ST3146855LC 00P3837 00P3836 ST31468.54493030.43383044 16582 (80 pin-pScallop)

146GB ST3146855LW 10N7196 10N7222 ST31468.54493030.43383044 16582 (68 pin-Bare)

146GB ST3146855LC 03N6350 03N6349 ST31468.54493030.43383044 16582 (80 pin-U320 Carrier)

146GB ST3146855LC 03N6352 03N6351 ST31468.54493030.43383044 16582 (80 pin-U320-HV)

300GB ST3300655LW 10N7198 10N7223 ST33006.54493030.43383044 16582 (68 pin-Bare)

300GB ST3300655LC 10N7211 10N7195 ST33006.54493030.43383044 16582 (80 pin-U320 carrier)

300GB ST3300655LW 03N5257 10N7223 ST33006.54493030.43383044 16582 (68 pin-Bare)

300GB ST3300655LC 03N6335 10N7223 ST33006.54493030.43383044 16582 (80 pin-U320 carrier)

300GB ST3300655LC 03N6337 10N7223 ST33006.54493030.43383044 16582 (80 pin-U3-HV)

1.2 Microcode Change History

Release date	Code level	Change Description
July 7, 2008	C80D	Corrected capacity values for 9.1 GB (introduced in C80A code).
April 14, 2008	C80A	After a drive reports error in AIX error log, and running AIX ELA (Error Log Analysis), drive reports zero for FFC (Failing Function Code). Also made code changes to support older disk drive FRU’s.
November 2007	C808	Changes made to drive microcode to monitor the number of CRC errors (drive-adapter communication errors), and if rate of CRC errors exceeds threshold, SCSI bus speed will change from 320MB/sec to 160MB/sec.
April, 2007	C806	Initial Release

===============================================================

2. AIX Operating System

2.1 Installation Time

Approximately 20 minutes if drive is part of rootvg(using Diagnostics CD); Approximately 5 minutes/drive if drive is not part of rootvg(using concurrent diagnostics).

2.2 Determine Drive Model, FRU&PN and Current Microcode Level

2.2.1 SCSI Drives attached to SCSI Controllers and PCI-X RAID Adapters

To see the drive type and current microcode level, Execute the following command:
lscfg -vl hdisk* |pg ; For drives NOT configured for RAID

lscfg –vl pdisk* |pg ; For drives configured for RAID

DEVICE LOCATION DESCRIPTION

hdisk16 U787F.001.DPM17R3-P1-C3-T2-L4-L0 16 Bit LVD SCSI Disk Drive (300000 MB)

Manufacturer................IBM

Machine Type and Model......ST3300655LC

FRU Number..................10N7211

ROS Level and ID............43383044

Serial Number...............00002C95

EC Level....................D76038

Part Number.................10N7195

Device Specific.(Z0)........000004129F000136

Device Specific.(Z1)........0309C80D

Device Specific.(Z2)........0002

Device Specific.(Z3)........06211

Device Specific.(Z4)........0001

Device Specific.(Z5)........22

Device Specific.(Z6)........D76038

Brand.......................

If the data returned in the Part Number”, FRU Number, and Machine Type and Model fields match the one listed in section 1.1 AND the "ROS Level and ID...." field of that data is below "43383044", this microcode applies.
Note: Drive microcode level in ROS Level and ID … field is displayed in Hex value of ASCII characters in VPD data. Each alpha-numeric ASCII character converts to a 2-digit hex number. For example in VPD displayed above, 33 Hex= ASCII character "C"; 38 Hex= ASCII character "8"; 30 Hex=ASCII character "0"; 44 Hex=ASCII character "D", microcode level is "C80D". Also note that the microcode level "C80D" is displayed in Z1” field.

2.2.2 SCSI Drives attached to PCI SCSI RAID Controllers

At AIX command line, type:
Diag
Select "Task Selection" from diagnostics menu.
Select "PCI RAID Physical Disk Identify"
Select SCSI RAID Adapter (press enter, then F7 to Commit)
This will display the Vital Product Data for Physical Disk drives attached to the RAID adapter.

===============================================================

2.3 Transferring and Unpacking the Microcode Update Package

2.3.1 Internet AIX self extracting file (.bin)

a) Make a directory on an AIX system to receive the AIX format file.
Enter: mkdir /tmp/fwupdate
b) Transfer the AIX format file to /tmp/fwupdate directory (using "Save as ...").
You'll see the filename is CH15K5.bin
c) Unpack the file by executing the instructions below.
Enter the commands:
cd /tmp/fwupdate
chmod +x CH15K5.bin
./CH15K5.bin
[Don't overlook the periods (.) in the above command.]

The directory CH15K5 with microcode files listed in section 1.1 will be added to /tmp/fwupdate.

d-Enter the following command to copy the microcode files to " /etc/microcode " directory :
cp /tmp/fwupdate/CH15K5/ST3* /etc/microcode

e- If transferring files to a different system using floppy diskettes, use the following procedure to copy files to diskette
Note: Don't overlook the complete path of microcode files, AIX Diag microcode download will not work if files are not copied with complete path onto the diskette. Enter the following command to copy microcode file(s) onto a floppy diskette
ls /etc/microcode/ microcodefilename | backup -ivf /dev/rfd0
where microcodefilename is microcode file that is needed, for example:
ls /etc/microcode/ ST37345.54493030.43383044| backup -ivf /dev/rfd0

2.3.2 Internet RPM package

Note: The instructions that follow are specific AIX commands. AIX commands are CASE (lower and upper) SENSITIVE, and must be entered exactly as shown, including filenames.

a) Make a directory on an AIX system to receive the RPM format file.
Enter: mkdir /tmp/microcode

b) Transfer the RPM format file to the /tmp/microcode directory (using "Save as ...").
You'll see the filename is CH15K5-C80D-AIX.rpm

c) Unpack the file by executing the instructions below:
Enter the commands:
rpm -ihv --ignoreos --force CH15K5-C80D-AIX.rpm

(note double dash --)

The file size and checksum will be verified.

The microcode files will be added to /etc/microcode/

2.3.3 CD-ROM

Copy microcode updates from the CD-ROM to standard locations on your local disk:

1. RPM packaged microcode files will be copied to "/tmp/microcode/RPM"
2. Microcode files will be copied to /usr/lib/microcode

Notes:
- "/etc/microcode" is a symbolic link to "/usr/lib/microcode".
- If permission does not allow the copy to the above stated directory
or file then the user will be prompted for a new location.
========================================================

2.4 Microcode Download Procedure

2.4.1 SCSI Drives Attached to SCSI Adapter

Warning: Do not power off the system or the drive during microcode download as this may permanently damage the disk drive

NOTE: Please save current and older versions of the microcode update files in case you need to restore your system.

Caution: The microcode download process is nondestructive to the hard disks; however, as a precaution, ensure that a backup operation has been performed on the affected systems PRIOR to the microcode installation.

Can microcode be installed Concurrently?
AIX level 5.1 and above supports concurrent microcode download on all drives, including drives that are part of rootvg.
AIX level 4.33 and below does not support concurrent microcode download if drive is part of rootvg, microcode download can ONLY be performed in service mode(stand alone) using diagnostics CD. If disk is not part of rootvg, microcode download can be performed cuncurrently as long as drive is not in use.

Is system reboot needed to activate the microcode: Yes if stand alone diagnostics is used, NO if concurrent diagnostics is used.

Installation Time: Approximately 20 minutes/drive if stand alone diagnostics is used(using Diagnostics CD); Approximately 5 minutes/drive if consurrent diagnostics is used.

2.4.1.1 AIX level 5.1 and above

2.4.1.2.1 Concurrent Download

1. Type diag at the prompt.
2. Select the "Task Selection" from diagnostics menu.
3. Select "Microcode Download" from "Task Selection" menu.
4. Select resource that microcode will be applied to(hdisk? For physical disk, pdisk for RAID configured disks) and press ENTER, then press "F7" to commit..
5- A small screen displays the message " *** NOTICE*** The microcode installation occurs while the attached drives are available for use..... "
    Press enter to continue
6. Select the source for microcode, use arrow key to go up/down, Enter to continue.
                      /etc/microcode
                      diskette

- Use /etc/microcode if "restore" command is used to copy files from diskette onto the disk
- Use diskette if using diskette as the source for download

NOTE: A prompt will ask you to insert the microcode diskette in diskette drive(if Diskette is selected above). Insert the diskette and press ENTER

7- Display shows a list of microcode files available for the selected drive, highlight option "M ST3xx...", the latest microcode for the drive and press ENTER. A message may warn you that current level of microcode is not available on the media, press ENTER to continue.

8. You will receive a msg. "Current Microcode is...." and "Download has completed successfully"
(this may take a few minutes)
9. Return to the Tasks Selection menu and repeat this procedure for each hard disk that requires this microcode.
10. Exit diagnostic(and reboot if needed).

2.4.1.2 AIX level 4.33:
This procedure is for drives that are not part of rootvg or paging space:
1. This step is optional. Microcode download can be performed either from Diskette or from Disk. To copy files from the diskette to disk, place the diskette containing microcode files into diskette drive A, at AIX Prompt type   restore
2- At AIX prompt, type   diag
3. Select the "Task Selection" from diagnostics menu.
4. Select "Microcode Download" from "Task Selection" menu.
5. Select resource that microcode will be applied to(hdisk?) and press ENTER.
6. Press "F7" to commit.
     (The current microcode level of the resource you selected earlier will be displayed at the top of the screen)
7. Make the following selections on the next screen:
    Select Input Device --------------------------------------- [ diskette] <---------- Disk can be used if "restore" command is used in step 1
    Microcode level to download ----------------------------- [ latest]
    Download latest level even if ------------------------------ [ yes]
    current is missing
NOTE: A prompt will ask you to insert the microcode diskette into the floppy drive(if Diskette is selected above). Insert the diskette which accompanies these instructions. If this level is already installed in the drive you've selected a message will let you know. A message also may come up to let you know that the Diskette(or Disk) does not have the previous level microcode file. This is true and is not required to complete the download.
PRESS "F7" to commit
8. You will receive a msg. "Current Microcode is....and...Download has completed successfully"
       (this may take a few minutes)
9. Return to the Tasks Selection menu and repeat this procedure for each hard disk that requires this microcode.
10. Exit diagnostic.

2.4.1.2.2 Standalone (Service Mode) Download

This procedure is used for all drives including rootvg or paging space drives
1. Properly shutdown the system.
2. Boot up the system in standalone diagnostics mode with the CDROM diagnostics(Use diagnostics level 4.21 or above; It is recommended to use the same level
    of Diagnostic CD as the AIX ).
3. Select the "Task Selection" from diagnostics menu.
4. Select "Microcode Download" from "Task Selection" menu.
5. Select resource that microcode will be applied to(hdisk?) and PRESS ENTER.
6. Press "F7" to commit.
      (The current microcode level of the resource you selected earlier will be displayed at the top of the screen)
7. Make the following selections on the next screen:
    Select Input Device --------------------------------------- [ diskette]
    Microcode level to download -----------------------------[ latest]
    Download latest level even if -----------------------------[ yes]
    current is missing

NOTE: A prompt will ask you to insert the microcode diskette into the floppy drive. Insert the diskette which accompanies these instructions. If this level is already installed in the drive you've selected a message will let you know. A message also may come up to let you know that the Diskette(or Disk) does not have the previous level microcode file. This is true and is not required to complete the download.
PRESS "F7" to commit
8. You will receive a msg. "Current Microcode is...." and "Download has completed successfully"
(this may take a few minutes)
9. Return to the Tasks Selection menu and repeat this procedure for each hard disk that requires this microcode.
10. Exit diagnostic and reboot system in normal mode.

2.4.2 SCSI Drives Attached to PCI RAID Adapter

NOTE: Please save current and older versions of the microcode update files in case you need to restore your system.

1. At AIX Command line type:
diag
2. Select the "Task Selection" from diagnostics menu.
3. Select "Microcode Download" from "Task Selection" menu.
4. Select RAID controller from the list of resources, PRESS ENTER, then F7 to commit
5. Select "Physical Disks" and PRESS ENTER
6. A list of all Physical Disks will be displayed, select the disk that needs to be upgraded, PRESS ENTER and F7 to commit.
7. Select "Latest level"
8. Select "Disk" if files are copied to /etc/microcode directory. Select "Diskette" if microcode files are saved onto a diskette, PRESS ENTER
(The current microcode level of the resource you selected earlier will be displayed at the top of the screen)

9. You will receive a message "Download has completed successfully" and "Current Microcode is" (this may take a few minutes).
10. Return to the Previous menu and repeat this procedure for each hard disk that requires this microcode.
11. Exit diagnostic and reboot system.

======================================================

3. Linux Operating System

3.1 Linux 2.6 kernel(such as SuSE SLES 9 or RHEL 4)

Microcode can be updated using the iprconfig utility. The iprconfig utility

allows for multiple levels of adapter and device microcode to exist on the

system at the same time. After the device to update microcode is

selected, all available microcode levels are presented to choose to download.

a) If using SLES 9 base, install the package by typing:

rpm -ivh --ignoreos CH15K5-C80D-AIX.rpm

b) If using SLES 9 SP1 or better or RHEL 4 or better, install the package by typing:

rpm -ivh CH15K5-C80D-LINUX.rpm

2. Update the microcode by typing:

iprconfig

Press Enter.

3. Select Download microcode and press Enter.

4. Select the device you wish to update by typing a 1 then pressing Enter. Multiple devices may be selected.

5. Select the microcode image to be downloaded to the device by typing a 1 then pressing Enter.

6. Press Enter again to confirm the download (display shows “Microcode Download in Progress” with elapsed time)

7. If multiple devices were selected, repeat from Step 5 for the next device.

To check the microcode level:

1. Start iprconfig utility,

2. Select "Display hardware status" option.

3. Select disk to query by typing a 1 next to it and pressing "Enter"

4. Look at the "Firmware Version" field

--------------------------------------------------------------------------

3.2 RHEL 3:

Microcode can be updated using the iprupdate utility. If iprupdate finds newer

microcode on the system it will be downloaded to the disk.

1. Install the package by typing:

rpm -ivh --ignoreos CH15K5-C80D-AIX.rpm

Press Enter.

2. Update the microcode by typing:

iprupdate

Press Enter.

To check the microcode level:

1. Start iprconfig utility,

2. Select "Display disk hardware status" option.

3. Find the disk you wish to query and note its serial number.

4. Type "d" to get to the "Display disk unit details" screen.

5. Select disk to query by typing a 5 next to it and pressing "Enter"

6. Look at the "Firmware Version" field

-------------------------------------------------------------------------

3.3 SLES 8 SP4

Microcode can be updated using the sisupdate utility. If sisupdate finds newer

microcode on the system it will be downloaded to the disk.

1. Install the package by typing:

rpm -ivh --ignoreos CH15K5-C80D-AIX.rpm

Press Enter.

2. Update the microcode by typing:

sisupdate

Press Enter.

To check the microcode level:

1. Start sisconfig utility,

2. Select "Display disk hardware status" option.

3. Find the disk you wish to query and note its serial number.

4. Type "d" to get to the "Display disk unit details" screen.

5. Select disk to query by typing a 5 next to it and pressing "Enter"

6. Look at the "Firmware Version" field