IBM eserver xSeries 365 Remote Supervisor Adapter II Update Systems 8861 and 8862 [SERVICE USE RETAIN #H186055] (C) Copyright International Business Machines Corporation 1999, 2005. All rights reserved. US Government Users Restricted Rights - Use, duplication, or disclosure restricted by GSA ADP Schedule Contract with IBM Corp. CONTENTS ________ 1.0 Overview 2.0 Change History 3.0 Installation and Setup Instructions 4.0 Unattended Mode 5.0 Web Sites and support phone Number 6.0 Trademarks and Notices 7.0 Disclaimer 1.0 Overview ________________________ 1.1 This diskette will update the IBM Remote Supervisor Adapter II software only. It will not affect any device drivers. 1.2 Limitations If there is an error in loading the IBM Remote Supervisor Adapter II software, retry loading the software by repeating the instructions in section 3.0. 1.3 Enhancements - none 1.4. Level of Recommendations and Prerequisites for the update: - Multi-lun support is needed in order to mount more then one remote drive simultaneously. The linux kernel 2.4.20 and later have the appropriate multi-lun support, however this support needs to be enabled at kernel build time. Currently, only the SLES 8.0 SP3 distribution has multi-Lun support available and enabled. RedHat AS 3.0 has a 2.4.21 kernel, but does not have multi-lun support enabled by default. 1.5 Dependencies: - none 2.0 Installation and setup instructions To install this update, perform the following steps: a). Open a Web browser. In the address or URL field, type the IP address or host name of the Remote Supervisor Adapter II to which you want to connect. The Enter Network Password window opens. Note: The Remote Supervisor Adapter II defaults to DHCP. If a DHCP host is unavailable, the Remote Supervisor Adapter II assigns a static IP address of 192.168.70.125. b). Type your user name and password in the Enter Network Password window. If you are using the IBM Remote Supervisor Adapter II for the first time, you can obtain your user name and password from your system administrator. All login attempts are documented in the event log. A welcome page opens in your browser. Note: The Remote Supervisor Adapter II is set initially with a user name of USERID and password of PASSW0RD (with a zero, not an O). This user has read/write access. Change this default password during your initial configuration for enhanced security. c). Select a timeout value, in minutes, in the field provided. If your browser is inactive for that number of minutes, the Remote Supervisor Adapter II logs you off the Web interface. d). Click Continue to start the session. The browser opens the System Health page, which gives you a quick view of the system status. e). In the navigation frame, click Firmware Update under Tasks, then click Browse. f). Navigate to the PKT file you want to update. Note: There are five packet files that can be updated: RAETBRUS.PKT Remote Supervisor Adapter Boot ROM RAETMNUS.PKT Remote Supervisor Adapter Main Application DMCFLASH.PKT Integrated System Management Processor IIOEFLSH.PKT Intelligent I/O Expansion Integrated System Management Processor IIOEFLPB.PKT Intelligent I/O Expansion Power Backplane Controller Repeat steps e through k for each packet on this diskette. The packets should be flashed in the order listed above. The IIOEFLSH.PKT and IIOEFLPB.PKT packet files can be omitted if there is no Intelligent I/O Expansion unit attached to the server. If there is an Intelligent I/O Expansion unit attached to the server, it must be powered on before flashing the IIOEFLSH.PKT and IIOEFLPB.PKT packet files. g). Click Open. The file (including the full path) appears in the box beside Browse. h). To begin the update process, click Update. A progress indicator opens as the file is transferred to temporary storage on the Remote Supervisor Adapter II. A confirmation page opens when the file transfer is completed. i). Verify that the PKT file shown on the Confirm Firmware Update page is what you intend to update. If not, click the Cancel button. j). To complete the update process, click Continue. A progress indicator opens as the firmware on the Remote Supervisor Adapter II is flashed. A confirmation page opens to verify that the update was successful. k). Repeat steps e through k for each packet. l). After receiving a confirmation that the update process is complete, click the option "Restart ASM" and click the Restart button. Click OK to confirm that you want to restart the Remote Supervisor Adapter II. NOTE: Restarting the Remote Supervisor Adapter II will disconnect your current session. m). Click OK to close the current browser window. n). To log into the Remote Supervisor Adapter II again, open your browser and follow the regular login process. Note: To cancel this process at any point, click Cancel. 3.0 Configuration information The Remote Supervisor Adapter II can be configured using the web browser interface. To access the Remote Supervisor Adapter II web interface, perform the following steps. a). Open a Web browser. In the address or URL field, type the IP address or host name of the Remote Supervisor Adapter II to which you want to connect. The Enter Network Password window opens. Note: The Remote Supervisor Adapter II defaults to DHCP. If a DHCP host is unavailable, the Remote Supervisor Adapter II assigns a static IP address of 192.168.70.125. b). Type your user name and password in the Enter Network Password window. If you are using the IBM Remote Supervisor Adapter II for the first time, you can obtain your user name and password from your system administrator. All login attempts are documented in the event log. A welcome page opens in your browser. Note: The Remote Supervisor Adapter II is set initially with a user name of USERID and password of PASSW0RD (with a zero, not an O). This user has read/write access. Change this default password during your initial configuration for enhanced security. 4.0 Unattended mode This update does not support unattended installation. 5.0 Web information and support phone numbers You can download new and updated files for IBM products from http://www.ibm.com/support/. For a list of supported operating systems, see http://www.ibm.com/servers/eserver/serverproven/compat/us/. You can receive hardware service through IBM Services or through your IBM reseller, if your reseller is authorized by IBM to provide warranty service. See http://www.ibm.com/planetwide/ for support telephone numbers, or in the U.S. and Canada, call 1-800-IBM-SERV (1-800-426-7378). In the U.S. and Canada, hardware service and support is available 24 hours a day, 7 days a week. In the U.K., these services are available Monday through Friday, from 9 a.m. to 6 p.m. 6.0 Notices and trademarks The following terms are trademarks of International Business Machines Corporation in the United States, other countries, or both: IBM Predictive Failure Analysis Netfinity ServeRAID Netfinity Manager ServerGuide UNIX is a registered registered trademark of The Open Group in the United States and other countries. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation in the United States, other countries, or both. Linux is a trademark of Linus Torvalds in the United States, other countries, or both. Java and all Java-based trademarks and logos are trademarks of Sun Microsystems, Inc. in the United States, other countries, or both. Adaptec and HostRAID are trademarks of Adaptec, Inc. Novell, and SUSE are registered trademarks of Novell, Inc., in the United States and other countries. Red Hat is a registered trademark of Red Hat, Inc. Other company, product, or service names may be trademarks or service marks of others. 7.0 Disclaimer THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS.