IBM System x3650 Baseboard Management Controller (BMC) Update CD ROM
Version 1.10 (Build ID GGBT24AUS)


System Machine Type 7979


CONTENTS
________

1.0  Overview
2.0  Installation and Setup Instructions
3.0  Configuration Information
4.0  Unattended Mode
5.0  Web Sites and support phone Number
6.0  Trademarks and Notices
7.0  Disclaimer


1.0  Overview
________________________

This CDROM will update the Baseboard Management Controller (BMC) firmware
only.  It will not affect any device drivers.


        1.1     To use this CDROM, perform the following steps:

                a).     Make sure BIOS version 1.00, or later, is installed.

                b).     Insert this CDROM into the CDROM drive and
                        restart the system.  If your system does not boot from
                        the CDROM, use POST/BIOS setup to configure the
                        CDROM drive as a boot device.  Please refer to the
                        Server Library that was included with your system for
                        additional information.

                c).     Once your system boots, a ramdrive will be created,
                        the appropriate files will be copied to this ramdrive
                        and the BMC update firmware update will execute
                        automatically.

                d).     When you are finished using the utility, remove the
                        CDROM from the CDROM drive and restart your
                        system.

        1.2     Limitations

                If there is an error in loading the BMC firmware retry
                loading the software by repeating the instructions in
                section 1.1.

        1.3     Enhancements

                - none

        1.4.    Level of Recommendations and Prerequisites for the
                update:

                - BIOS version 1.00, or later, must be installed prior to
                  installing this BMC firmware update.

                - A full tape backup should be completed and verified
                  prior to running this, or any other system upgrade.

                - RAID configuration should be saved to a diskette:
                  see the "Hardware Maintenance Manual" for more details.

        1.5     Dependencies:

                - none


2.0  Installing and Setup Instructions
______________________________________

To install the firmware on this CDROM, perform the following steps:

        2.1     Make sure BIOS version 1.00, or later, is installed.
        2.2     Make sure your system is powered down.
        2.3     Insert the CDROM in the CDROM drive.
        2.4     Power on your system to boot from CDROM drive.
                If your system does not boot from the CDROM, use
                POST/BIOS setup utility to configure the CDROM drive
                as a boot device.
        2.5     Once your system boots, a ramdrive will be created, the
                appropriate files will be copied to this ramdrive and the
                BMC update firmware update will execute automatically.
        2.6     When the update completes, remove the CDROM from the drive
                and restart the system.
        2.7     You may clear the BMC's SEL.


3.0  Configuration Information
______________________________________

        There is no configuration information necessary.


4.0     Unattended Mode
_______________________

This update utility does not support unattended installations but there are other
ways to incorporate unattended installations of this code. Check the UpdateXpress
CD for availability of unattended installs of this firmware.  (The UpdateXpress
CD is downloadable from http://www.ibm.com (use the search function to find
"UpdateXpress").


5.0     WEB Sites and Support Phone Number
__________________________________________

        5.1     IBM Support Web Site:
                http://www.pc.ibm.com/support

        5.2     IBM System x Web Site:
                http://www.ibm.com/systems/x/


6.0.    TradeMarks and Notices
______________________________

        6.1     The following terms are trademarks of the IBM
                Corporation in the United States, or other countries
                or both:
                            * IBM
                            * Netfinity
                            * Netfinity Manager
                            * Advanced System Management

                Other company, product, and service names may be
                trademarks or service marks of others.


7.0.    Disclaimer
__________________

        7.1     THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF
                ANY KIND.  IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS
                OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED
                WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND
                MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN
                THIS DOCUMENT.  BY FURNISHING THIS DOCUMENT, IBM
                GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS.

        7.2     Note to Government users:

                Note to U.S. Government users-- Documentation related
                to restricted rights-- Use, duplication and disclosure
                is subject to restrictions set forth in GSA ADP Schedule
                Contract with IBM Corporation.


(C) Copyright International Business Machines Corporation 2005, 2006.
    All rights reserved.