IBM IntelliStation M40 Flash Update Version 1.30 Installation README File CONTENTS ________ 1.0 Overview 2.0 Change History 3.0 Installation and Setup Instructions 4.0 Configuration Information 5.0 Unattended Mode 6.0 Web Sites and Support Phone Number 7.0 Trademarks and Notices 8.0 Disclaimer 1.0 Overview 1.1 This README file contains the latest information about installing the IBM IntelliStation M40 POST/BIOS code. 1.2 Limitations - NA 1.3 Enhancements - NA 1.4 Level of Recommendations and Prerequisites for the Update: 1.5 Dependencies 2.0 Change History BIOS Version 1.30 -Corrected a problem where a SBE (Single Bit Error) on DRAM DIMM1 would be incorrectly reported as DIMM3. With this change the SBE's are correctly reported on the failing DIMM. BIOS Version 1.29 - Correct a issue that when CMOS backup battery is removed, the system can not boot successfully at first time the battery is restore back. BIOS Version 1.28 - Correct Presler CPU L2 cache size information. - Update Presler CPU micro-code by Intel's request. BIOS Version 1.27 - Support Intel CPU: Cedar Mill and Presler. - Support RDM WCI function. BIOS Version 1.26 - Support RDM WNI function. - Support HostRaid mode for SATA and SCSI hard drive. BIOS Version 1.25 - Support ASF 2.0 function. - Support Chassis intruder-detection feature. Bios Version 1.24 - This is the initial release. 3.0 Installation and Setup Instructions The procedure to update the POST/BIOS is as follows: 3.1 Insert the "IntelliStation A10 POST/BIOS Flash Diskette" into drive A. 3.2 Start up or restart your IBM system. 3.3 The system will boot off of the diskette. 3.4 You will then be asked if you would like to save the current code to a diskette. If you select 'Y', you need to name the file to be saved. The file will be saved on the diskette. If you select 'N', the utility will continue to the next step. 3.5 At this point, you will be asked if you would like to continue the POST/BIOS flash update. If you select 'Y', the system will update the flash ROM with the new code. When this is complete you will be prompted to remove the diskette and hit 'F1' to reboot the system. 3.6 On the first system boot, after updating the BIOS, select the Setup Utility with the F1 key; then, select the "Load Default Settings" option. Select the "Save Settings" option, and hit 'y' to save. Then, select "Exit Setup" to exit the utility, and, finally, accept the displayed 'Y' option under "Save and exit the setup utility?" 4.0 Configuration Information 5.0 Unattended Mode 5.1 Steps for unattended mode. 5.1.1 Modify AUTOEXEC.BAT on the Flash Diskette to read: "AF.EXE flashfil.fls /py /sn", where 'flashfil.fls' is the file you wish to flash 5.1.2 Reboot the system with the Flash Diskette in Drive A: 6.0 Web Sites and Support Phone Number 6.1 IBM Support Web Site: http://www.pc.ibm.com/support 6.2 IBM Marketing IntelliStation Web Site: http://www.pc.ibm.com/intellistation 6.3 If you have any questions about this update, or problems applying the update go to the following Help Center World Telephone Numbers URL: http://www.ibm.com/planetwide/. 7.0 Trademarks and Notices THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. 8.0 Disclaimer