IBM eserver xSeries 226 Remote Supervisor Adapter II Update for Windows System 8648 Version 1.04, Build ID: PME812A, Revision 16 CONTENTS ________ 1.0 Overview 2.0 Change History 3.0 Installation and Setup Instructions 4.0 Unattended Mode 5.0 Web Sites and support phone Number 6.0 Trademarks and Notices 7.0 Disclaimer 1.0 Overview ________________________ 1.1 This diskette will update the IBM Remote Supervisor Adapter II software only. It will not affect any device drivers. 1.2 Limitations If there is an error in loading the IBM Remote Supervisor Adapter II software, retry loading the software by repeating the instructions in section 3.0. 1.3 Enhancements - none 1.4. Level of Recommendations and Prerequisites for the update: - Multi-lun support is needed in order to mount more then one remote drive simultaneously. The linux kernel 2.4.20 and later have the appropriate multi-lun support, however this support needs to be enabled at kernel build time. Currently, only the SLES 8.0 SP3 distribution has multi-Lun support available and enabled. RedHat AS 3.0 has a 2.4.21 kernel, but does not have multi-lun support enabled by default. 1.5 Dependencies: - none 2.0 Change History ________________________ IBM Remote Supervisor Adapter II Update Version 1.04, PME812A - Generate an alert when the power backplane consistently fails to respond to status requests. - Stopped generating the periodic SMIs used for Machine Check Architecture support. IBM Remote Supervisor Adapter II Update Version 1.03, PME811A - Changed the VRM thresholds to nominal +/- 200 mV for warnings and nominal +/- 250 mV for shutdowns IBM Remote Supervisor Adapter II Update Version 1.02, PME810A - Corrected a problem where the server could become non-responsive 76 days after the Remote Supervisor Adapter II has been reset. - Change the response to the 0x1A remote disk command to UNSUPPORTED because CDROM drives can't handle the 0x1A command. - Added DASD backplane temperature threshold values to the web page. - Dynamically adjust the VRM thresholds to match the VRM voltage changes that occur while the system is running to support new higher speed CPUs. IBM Remote Supervisor Adapter II Update Version 1.01, PME807A - Changed fan numbering from 1,2 and 3 to 1,2, and 4. - Prevent a possible system hang during a reboot. - Recover an intermittent I2C bus hang. IBM Remote Supervisor Adapter II Update Version 1.00, PME806A - First release 3.0 Installing and Setup Instructions ______________________________________ This utility will update the IBM Remote Supervisor Adapter II software under the Windows Operating System. It requires the installation of the correct Remote Supervisor Adapter II for Windows device driver. 3.1 Performing this code update (GUI) _______________________________________ - Run the "IBM xSeries 226 Windows Remote Supervisory Adapter II Update" by double-clicking the .EXE. - Choose "Perform Update" and click the "Next" button. - If the update is meant for the system on which it is running, the "Next" button will appear. Click the "Next" button to continue. - Click the "Exit" button. 3.2 Extracting the Windows update files (GUI) _______________________________________________ - Run the "IBM xSeries 226 Windows Remote Supervisory Adapter II Update" by double-clicking the .EXE. - Choose "Extract to Hard Drive" and click the "Next" button. - Choose a directory into which the Windows update files will be saved in the "Save As" dialog. - The files extracted are all the files that are necessary to perform a RSAII firmware update under Windows. Run "wflash -r" from a command line to update RSAII firmware on 32-bit Windows or "wflash64 -r" from a command line to update RSAII firmware on 64-bit Windows. - Click the "Exit" button. 4.0 Unattended Mode ________________________ Extracting the Windows update files (command line) __________________________________________________ - Run the "IBM xSeries 226 Windows Remote Supervisor Adapter II Update" with the following command line: ".exe -s -a -x " where .exe is the downloaded update and is the path to which the Windows update files will be extracted. - The files extracted are all the files that are necessary to perform a RSAII firmware update under Windows. Run "wflash -r" from a command line to update RSAII firmware on 32-bit Windows or "wflash64 -r" from a command line to update RSAII firmware on 64-bit Windows. 5.0 WEB Sites and Support Phone Number _________________________________________ 5.1 IBM Support Web Site: http://www.pc.ibm.com/support 5.2 IBM eserver xSeries Web Site: http://www.ibm.com/eserver/xseries 5.3 If you have any questions about this update, or problems applying the update, go to the following Help Center World Telephone Numbers and URL: http://www.pc.ibm.com/qtechinfo/YAST-3P2QYL.html. 6.0. TradeMarks and Notices ______________________________ 6.1 The following terms are trademarks of the IBM Corporation in the United States, or other countries or both: * IBM * Advanced System Management Other company, product, and service names may be trademarks or service marks of others. 7.0. Disclaimer __________________ 7.1 THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. 7.2 Note to Government users: Note to U.S. Government users-- Documentation related to restricted rights-- Use, duplication and disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corporation.