File Name: README.TXT IBM xSeries 380 (8663) BIOS/FIRMWARE Version 1.2 CONTENTS --------- 1.0 Overview 2.0 Change History 3.0 Installation and Setup Instructions 4.0 Configuration Information 5.0 Unattended Mode 6.0 Web Sites and Support Phone Number 7.0 Trademarks and Notices 8.0 Disclaimer 1.0 Overview: -------------- 1.1 About this code These files contain BIOS/FIRMWARE Version 1.2 code which supports the following Machine Type/Models of IBM xSeries 380: - 8683-1RX - 8683-2RX 1.2 Level of recommendations and prerequisites for the update: - The following Machine Type/Models of IBM xSeries 380 require BIOS/FIRMWARE Version 1.0 or higher: - 8683-1RX - 8683-2RX 1.3 Dependencies: - Determine the BIOS/FIRMWARE versions of your server before trying to upgrade the BIOS and Server management Firmware. - Valid BIOS and Firmware combinations are listed in the following table. BIOS# | BMC Ver# | HSC Ver# | CBC Ver# | SDR Ver# --------------------------------------------------- B100 | BMC 24 | HSC 7 | CBC 02 | SDR 14 B99 | BMC 24 | HSC 7 | CBC 02 | SDR 14 B83 | BMC 22 | HSC 7 | CBC 02 | SDR 13 - IMPORTANT: Recommend upgrading to at least BMC Rev 24 before using BIOS-99. 2.0 Change History -------------------- 2.1 IBM xSeries 380 BIOS/FIRMWARE Version 1.2. Includes: BIOS-100, BMC-24, HSC-07, CBC-02, SDR-14 Date : 098/26/2001 Stamp : 0109252309 BIOS Version : S460AC4A.86B.0100.B Processor Supported : C0 PAL/SAL/EFI REVISIONS PAL Version : 6.6.25 MSL Reference SAL Code : 6.0 RC9 SAL Specification Rev : 3.0 MSL Reference EFI Code : 12.38 EFI Specification Rev : 1.02 FPSWA Driver Version : 1.6 S460AC4.RCV Version : 9 2.2 IBM xSeries 380 BIOS/FIRMWARE Version 1.1. Includes: BIOS-99, BMC-24, HSC-07, CBC-02, SDR-14 Date : 08/30/2001 Stamp : 0108300108301658 BIOS Version : S460AC4A.86B.0099.B Processor Supported : C0 PAL/SAL/EFI REVISIONS PAL Version : 6.6.25 MSL Reference SAL Code : 6.0 RC9 SAL Specification Rev : 3.0 MSL Reference EFI Code : 12.38 EFI Specification Rev : 1.02 FPSWA Driver Version : 1.6 S460AC4.RCV Version : 9 2.3 IBM xSeries 380 BIOS/FIRMWARE Version 1.0. Includes: BIOS-83, BMC-22, HSC-07, CBC-02, SDR-13 Date : 06/07/2001 Stamp : 0106060029 BIOS Version : S460AC4A.86B.0083.B Processor Supported : C0 PAL/SAL/EFI REVISIONS PAL Version : 6.6.23 MSL Reference SAL Code : 6.0 RC9 SAL Specification Rev : 3.0 (Minimally) MSL Reference EFI Code : 12.36 EFI Specification Rev : 1.02 FPSWA Driver Version : 1.6 S460AC4.RCV Version : 9 3.0 Installation and Setup Instructions ----------------------------------------- 3.1 Download and Media Creation. 1. To Build a CD. - Download the "iso" image of the IBM xSeries 380 POST/FIRMWARE, from http://www.pc.ibm.com/support - Create a CD using instructions at following url: from http://www.pc.ibm.com/qtechinfo/MIGR-4NJNJB or other CD creation Applications. Note: To update the SDR records all files have to be on Read/write media, so copy all files from CD to the Hard Drive or LS120, and do the install. 2. To Build an LS-120 Diskette. - Download the 'zip' file of the IBM xSeries 380 POST/FIRMWARE, from http://www.pc.ibm.com/support - Expand the 'zip' files and copy all files to the LS-120. 3.2 The procedure to update the BIOS/FIRMWARE is as follows: 1. Boot to EFI Shell - Insert the LS-120 diskette or CD containing the BIOS/FIRMWARE utilities. - Type: map -r (Map's available devices) (find the file system (fsx:) defined to the specific media being used) Device:00 is LS-120, Device:FF is CD - Type: fsx: (fsx:=fs0:, or fs1:, or fs2:) - Type: load ipmi.efi (Load's ipmi driver) 2. To load BIOS 100, Type: iflash64 new_fw100.bin /update 3. Once it is done, power off the system. 4. Then clear the CMOS according to the following procedure: - Wait for 8 seconds after power off. - Hold the reset button for 4 seconds. - While holding the reset button, press the power button and release both at the same time. Note: This procedure does not clear the password. - You will get "NVRAM cleared by Jumper" message. - Enter CMOS setup and set the date and time to current date and time if needed. - Save settings. System will automatically reboot to EFI. 4.0 WEB Sites and Support Phone Number ---------------------------------------- 4.1 IBM Support Web Site: http://www.pc.ibm.com/support 4.2 IBM Marketing eserver Web Site: http://www.ibm.com/eserver/xseries 4.3 If you have any questions about this update, or problems applying the update go to the following Help Center World Telephone Numbers URL: http://www.pc.ibm.com/qtechinfo/YAST-3P2QYL.html. 5.0 Trademarks and Notices ---------------------------- 5.1 IBM is a registered trademark of International Business Machines Corporation. 5.2 Intel is a registered trademark and Itanium is a registered trademark of Intel Corporation. 5.3 Microsoft is a registered trademark and Windows NT, Windows, are trademarks of Microsoft. 5.4 Novell and NetWare are registered trademarks of Novell. Inc. 5.5 SCO, SCO UNIX, Open Desktop, Open Server are registered trademarks of Santa Cruz Operation, Inc. 5.6 All other trademarks are the properties of their respective owners. 6.0 Disclaimer ---------------------------- 6.1 THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. 6.2 Note to Government Users Include the following note after the disclaimer paragraph. Note to U. S. Government Users -- Documentation related to restricted rights -- Use, duplication or disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corporation.