=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= Adaptec 7800 Family Manager Set for Windows NT =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= Welcome to Adaptec 7800 Family Manager Set =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= The following information is available in this README file: o Supported Hardware o Changes From Prior Release o Installation Instructions o Known Issues o Additional Notes o Command Line Options o Diskette Contents o Contacting Adaptec =-=-=-=-=-=-=-=-=-= Supported Hardware =-=-=-=-=-=-=-=-=-= The following Adaptec SCSI Host Adapters are supported: Adaptec Host Adapter Description -------------------- ----------- AVA-2902I PCI-to-Fast SCSI (non-bootable, internal) AVA-2902E PCI-to-Fast SCSI (non-bootable, external) AVA-2904 PCI-to-Fast SCSI (non-bootable) AHA-2910 PCI-to-Fast SCSI (non-bootable) AHA-2930 PCI-to-Fast SCSI AHA-2940 PCI-to-Fast SCSI AHA-2940W PCI-to-Fast and Wide Single-ended SCSI AHA-2940AU PCI-to-Ultra Single-ended SCSI AHA-2940U PCI-to-Ultra Single-ended SCSI AHA-2940U Dual DualChannel PCI-to-Ultra Wide Internal Single-ended SCSI with 50-pin external connector AHA-2940UW PCI-to-Ultra Wide Single-ended SCSI AHA-2940UW Dual DualChannel PCI-to-Ultra Wide Single-ended SCSI with Wide external connector AHA-2944W PCI-to-Fast and Wide Differential SCSI AHA-2944UW PCI-to-Ultra Wide Differential SCSI AHA-3940 MultiChannel PCI-to-Fast SCSI AHA-3940W MultiChannel PCI-to-Fast and Wide SCSI AHA-3940U MultiChannel PCI-to-Ultra SCSI AHA-3940UW MultiChannel PCI-to-Ultra Wide SCSI AHA-3940UWD MultiChannel PCI-to-Ultra Wide SCSI with dual external connectors AHA-3944W MultiChannel PCI-to-Fast and Wide Differential SCSI AHA-3944UWD MultiChannel PCI-to-Ultra Wide Differential SCSI with dual external connectors AHA-3940AU MultiChannel PCI-to-Ultra SCSI AHA-3940AUW MultiChannel PCI-to-Ultra Wide SCSI AHA-3940AUWD MultiChannel PCI-to-Ultra Wide SCSI with dual external connectors AHA-3944AUWD MultiChannel PCI-to-Ultra Wide Differential SCSI with dual external connectors AHA-4944W Quad Channel PCI-to-Fast and Wide Differential SCSI AHA-4944UW Quad Channel PCI-to-Ultra Wide Differential SCSI AIC-7850 Single-chip PCI-to-Fast SCSI AIC-7855 Single-chip PCI-to-Fast SCSI AIC-7856 Single-chip PCI-to-Fast SCSI AIC-7860 Single-chip PCI-to-Ultra SCSI AIC-7870 Single-chip PCI-to-Fast and Wide SCSI AIC-7880 Single-chip PCI-to-Ultra Wide SCSI AIC-7895 Single-chip PCI-to-MultiChannel Ultra Wide SCSI =-=-=-=-=-=-=-=-=-=-=-=-=-= Changes From Prior Release =-=-=-=-=-=-=-=-=-=-=-=-=-= Adaptec 7800 Family Manager Set v2.1x features numerous enhancements including: o Support for new PCI IC's and host adapters o Better performance than the Adaptec 7800 Family Manager Set v1.30 and the embedded drivers for Windows NT 3.5x and 4.0. o Support for Windows NT v4.0. =-=-=-=-=-=-=-=-=-=-=-=-=-= Installation Instructions =-=-=-=-=-=-=-=-=-=-=-=-=-= This section describes installing and using the Adaptec 7800 Family Manager Set Driver (aic78xx.sys) for Windows NT. If you are performing a first time Windows NT installation, see Installing Windows NT v4.0 or Installing Windows NT v3.5x and the Driver, below. If Windows NT is already installed on your system, see Updating Windows NT v4.0 or Updating Windows NT v3.5x, below. Installing Windows NT v4.0 and the Driver ----------------------------------------- The following instructions explain how to install the Adaptec 7800 Family Manager Set v2.1x, while installing Windows NT v4.0. 1 Start your system with the Windows NT Boot Diskette in the floppy drive. 2 Insert diskette #2 when prompted. After a few moments you will see a blue screen. To setup Windows NT now, press ENTER. 3 Press S to skip Windows NT Setup's auto detection of your SCSI adapter. 4 Press S again to specify an additional device. 5 Press ENTER to select Others, and insert the Adaptec 7800 Family Manager Set v2.1x diskette. 6 Select the "Adaptec AHA-294x/AHA-394x/AHA-4944 or AIC-78xx PCI SCSI Controller (NT 4.0)" and press ENTER. 7 If you want to add other host adapters (that are not a part of the 7800 Family), do so at this time by pressing 'S' and repeating step 5 for each additional adapter and inserting the appropriate disk provided by the hardware manufacturer. The Adaptec 7800 Family host adapters use the same driver; it is not necessary to install the aic78xx.sys driver again. 8 Press ENTER to continue with the Windows NT operating system setup. Follow the instructions given on screen and in the Windows NT installation documentation. Installing Windows NT v3.5x and the Driver ------------------------------------------ The following instructions explain how to install the Adaptec 7800 Family Manager Set v2.1x, while you are installing Windows NT v3.5x. 1 If you choose to install Windows NT from a floppy drive, locate the Windows NT Disk 1 for Floppy Installation. If you are installing from a CD-ROM drive, locate the Windows NT Setup Disk 1 for CD-ROM Installation. 2 Insert the diskette into drive A (not drive B) and turn on your computer. When prompted, insert Windows NT Disk 2. 3 From the Welcome to Setup Screen, press ENTER to set up Windows NT. 4 When prompted, select Custom setup. (NOTE: If you select Express setup, the embedded aic78xx.sys driver included with Windows NT will be loaded and not the most recent version of the driver available from the Adaptec 7800 Family Manager Set v2.1x diskette for Windows NT.) 5 Press S to skip mass storage device detection. This allows you to manually select the Adaptec 7800 Family Manager Set v2.1x for your host adapter. 6 Since mass storage device detection was skipped in the previous step, Windows NT Setup displays none in the list of recognized devices. Press S to configure additional SCSI adapters. 7 From the list of additional SCSI adapters, expand the list, select Other, and press ENTER. (Requires disk provided by a hardware manufacturer). 8 Insert the Adaptec 7800 Family Manager Set v2.1x diskette into drive A and press ENTER. 9 The screen displays the adapter drivers supported on the diskette. Select the "Adaptec AHA-294x/AHA-394x/AHA-4944 or AIC-78xx PCI SCSI Controller (NT 3.5x)" and press ENTER. 10 If you want to add other host adapters (that are not a part of the 7800 Family), do so at this time by repeating Step 7 for each additional adapter and inserting the appropriate disk provided by the hardware manufacturer. The Adaptec 7800 Family host adapters use the same driver; it is not necessary to install the aic78xx.sys driver again. 11 Press ENTER to continue with the Windows NT operating system setup. Follow the instructions given on screen and in the Windows NT installation documentation. Updating Windows NT v4.0 ------------------------ Follow these instructions only if Windows NT v4.0 is already installed. 1 Click the Start button on the Winows NT task bar, and the point to Settings. 2 Open the Control Panel, double-click on SCSI Adapters. 3 Select the Drivers tab, and click the Add button. 4 In the "Install Driver" window, click the Have Disk button. 5 Insert the Adaptec 7800 Family Manager Driver v2.1x diskette. 6 At the "Copy manufacturer's files from" text box, type a:\winnt\4_0, and click OK. 7 At the Install Driver window, click OK. 8 In response to "Do you want to use the currently installed driver(s) or install new one(s)", select the New button. 9 Again type a:\winnt\4_0 and click continue. The driver is now installed. 10 You must restart your computer for the changes to take effect. Click Yes to restart your computer. Click No to return to the SCSI Adapters window. Updating Windows NT v3.5x ------------------------- Follow these instructions only if Windows NT v3.5x is already installed. 1 Select and start the Windows NT Setup program. (Its icon is usually found in the Main program group.) There is a brief pause while Windows NT Setup scans your hardware configuration. 2 Select the Options pull-down menu and then select Add/Remove SCSI Adapters. The SCSI Adapter setup program displays a list of all host adapters currently installed. 3 Click the Add button to add another host adapter type to the list. A list of additional SCSI adapters appears. 4 Expand the list of additional SCSI adapters; select Other and press ENTER. (Requires disk provided by the hardware manufacturer). 5 Insert the Adaptec 7800 Family Manager Set v2.1x diskette for Windows NT into drive A; enter the following path to the installation files and then click OK. a:\winnt\3_5 6 The screen displays the adapter drivers supported on the diskette. The "Adaptec AHA-294x/AHA-394x/AHA-4944 or AIC-78xx PCI SCSI Controller (NT 3.5x)" driver is highlighted by default, Click OK. The driver is added to the list of SCSI adapters. 7 Select "Adaptec AHA-294x/AHA-394x/AHA-4944 or AIC-78xx PCI SCSI Controller (NT 3.5x)" from the list of SCSI adapters and click Install. At this point, Windows NT Setup checks to see if the specified driver (in this example, aic78xx.sys) has already been copied to the system disk. 8 If the following message appears, click New to replace the existing driver and skip to Step 10. The driver(s) for this SCSI Adapter are already on the system. Do you want to use the currently installed driver(s) or install new one(s). If the following message appears, continue with Step 9: Please enter the full path to the Windows NT SCSI Adapter files. 9 Change the path to the directory (i.e., a:\winnt\3_5) with the desired device driver, then click Continue. The device driver is copied to your system disk and the Windows NT configuration is updated so that the new device driver loads when Windows NT reboots. 10 When the installation is complete, Windows NT Setup again displays a list of currently installed host adapter types. Verify that the new host adapter appears on the list; the string should look similar to "Adaptec AHA-294x/AHA-394x/AHA-4944 or AIC-78xx PCI SCSI Controller (NT 3.5x)". 11 Add other types of host adapters if necessary (see Step 4 above), or click Close to exit the SCSI adapters portion of Windows NT Setup, and then close the program. 12 When you see this message, click OK to exit: The changes you have made will not take effect until the computer is restarted If this message does not appear, no changes have been made to the Windows NT system configuration. 13 Restart your computer and Windows NT. It is possible that some drive letter assignments may change from the previous configuration. The remainder of this section describes removing and swapping of host adapters on Windows NT v3.5x and v4.0. Removing a Host Adapter on Windows NT 3.5x ------------------------------------------ Removing a host adapter can be as simple as physically removing it from the slot when your computer is shut down. Windows NT boots and functions properly in this configuration, but a warning message is generated every time you boot Windows NT. (CAUTION: If you have removed a host adapter but still have other host adapters of the same type installed in your computer, do not use Windows NT Setup to remove the device driver.) To eliminate the warning message, you must update the Windows NT software configuration, as described in the following steps: 1 Select and start the Windows NT Setup program. There is a brief pause while Windows NT Setup scans your hardware configuration. 2 Select the Options pull-down menu and then select Add/Remove SCSI Adapters. The SCSI Adapter setup program displays a list of all host adapters currently installed. 3 Select the host adapter you want to remove and click the Remove button. When the Windows NT Setup program asks you for confirmation, click OK. Because SCSI device drivers are loaded during system bootup and because they may be needed to load Windows NT itself, a screen may appear warning you that Windows NT may not start if you remove the SCSI adapter. 4 If you are sure you are removing the correct host adapter type, click OK. 5 Return to Step 3 if you want to remove driver support for other types of host adapters, or click Close to exit the SCSI adapters portion of Windows NT Setup. 6 Close the Windows NT Setup program. When the following message appears, click OK to exit. The changes you have made will not take effect until the computer is restarted. If this message does not appear, no changes have been made to the Windows NT system configuration. 7 Restart the computer. (NOTE: Windows NT Setup does not delete the device driver from your system disk; it only updates Windows NT software configuration information so that the device driver is no longer loaded during system bootup.) Removing a Host Adapter on Windows NT 4.0 ----------------------------------------- Removing a host adapter can be as simple as physically removing it from the slot when your computer is shut down. Windows NT boots and functions properly in this configuration, but a warning message is generated every time you boot Windows NT. (CAUTION: If you have removed a host adapter but still have other host adapters of the same type installed in your computer, do not use Windows NT Setup to remove the device driver.) To eliminate the warning message, you must update the Windows NT software configuration, as described in the following steps: 1 Open the Control Panel, double-click on SCSI Adapters. 2 Select the Drivers tab. 3 Select the driver you plan on removing and click the Remove button. The driver will appear as one of the following: "Adaptec AHA-294x/AHA-394x/AHA-4944 or AIC-78xx PCI SCSI Controller (NT 4.0)" or "Adaptec AHA-294X/AHA-394X or AIC-78XX PCI SCSI Controller" 4 If you are sure you are removing the correct host adapter type, click Yes. 5 You must restart your computer for the changes to take effect. Click Yes to restart your computer. Click No to return to the SCSI Adapters window. Swapping a Host Adapter for both v3.5x and v4.0 ----------------------------------------------- Swapping one type of host adapter for another is similar to the procedure for adding a host adapter. The important distinction is that you make all software configuration changes while Windows NT is running and before you make the hardware changes. (NOTE: If you do not install the driver that comes with the new host adapter, it may result in Windows NT failing to boot.) 1 Install the driver for the new host adapter by following the steps in Updating Windows NT with the Driver, above. It is not essential to remove the device driver for the host adapter you are replacing. Windows NT dynamically detects the absence or presence of host adapter hardware, and no problems should arise if you leave the existing device driver installed. You may remove the device driver later, after you have successfully rebooted Windows NT. However, if you leave the driver in, the system alerts you with an error message of the extra device driver every time you boot. See Removing a Host Adapter above. 2 Once the new device driver is installed, shut down Windows NT and replace the existing host adapter. 3 Restart your computer and Windows NT. It is possible that some drive letter assignments may change from the previous configuration. =-=-=-=-=-=-= Known Issues =-=-=-=-=-=-= o For Windows NT v3.5x, the embedded (included) miniport driver on the CD-ROM or diskettes, does not include support for Ultra host adapters (i.e., host adapters with the letters AU, U, UW, AUW, and AUWD at the end of the model number) and AHA-2944W. Refer to the installation instructions in Installing Windows NT v3.5x and the Driver. o For Windows NT v4.0, the embedded (included) miniport driver on the CD-ROM, does not include support for AHA-3940AUWD, AHA-3944AUWD, or AHA-4944W. Refer to the installation instructions in Installing Windows NT v4.0 and the Driver. o An issue exists in Windows NT 3.5x with the Windows NT Setup Application. In the Add/Remove SCSI Adapters selection, under the Options pull-down menu, you should see: "Adaptec AHA-294x/AHA-394x/AHA-4944 or AIC-78xx PCI SCSI Controller (NT 3.5x)" and possibly one or more of the following "Adaptec AHA-294x/AIC-78xx (PCI)" "Adaptec AHA-2940/AIC-78xx (PCI) NT v3.5x" as listed choices. This behavior is due to differences between the embedded SCSI.INF file and the OEMSCSx.INF that was created when installing/updating the aic78xx.sys. All of these choices, refer to the same Adaptec 7800 Family Manager Set v2.1x driver in your system. Removing any one of them, without the intention of either replacing or upgrading, may result in your system failing to boot. =-=-=-=-=-=-=-=-= Additional Notes =-=-=-=-=-=-=-=-= o If disconnection is disabled under SCSISelect for a hard disk device, the system may hang if the hard disk device supports tagged queuing. It is recommended to always enable disconnection for hard disk devices. By default, disconnection is enabled so no action is required. If for some unique requirements disconnection has to be absolutely disabled for hard disk devices, you can turn off tagged queue requests by editing the Windows NT Registry. You can do so by following these instructions: 1 Select Run from the File pull-down menu (Windows NT 3.5x), or Run from the Start button (Windows NT 4.0). 2 Enter REGEDT32 to run the Registry Editor. 3 Open \HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\aic78xx. 4 Create a key named Parameters by selecting Add Key from the Edit pull-down menu and entering "Parameters" (without quotations) in the edit-box for Key Name. Leave the Class edit-box blank. 5 Open Parameters and create a key named Device by selecting Add Key from the Edit pull-down menu. Enter "Device" (without quotations) in the Key Name edit-box. Leave the Class edit-box blank. 6 Open Device. Select the Add Value option from the Edit pull-down menu. In the Value Name edit-box, enter "DisableTaggedQueuing" (without quotations). Select the Data Type REG_SZ from the droplist combo box. 7 Shutdown and restart Windows NT. 8 Set Enable Disconnection to No for your particular device(s) in SCSISelect during bootup. (See your Host Adapter manual on how to use SCSISelect). o If the logical driver letters assigned by the BIOS change when the NT operating system is running, it's not an error. To preserve drive letter assignments between BIOS and NT, run the NT disk administrator and choose permanent drive letters assignments as an option. NT will then preserve logical driver letter assignments across boots and adapters. o The boot manager for Windows NT contains recovery logic to allow you to return to the last known good configuration. If you have changed your host adapter configuration and Windows NT no longer boots, follow these steps to recover: 1 Undo any hardware changes you have made to the computer since it was last operational. 2 Reboot the computer. Watch the display carefully during bootup. If the following message appears, press the Spacebar. Press spacebar NOW to invoke the Last Known Good menu Follow the instructions on the screen to continue booting with the last known good configuration. For Windows NT 4.0 only, hit the letter "L", to switch to the last known good configuration. 3 Once your computer is operational again, check all of the hardware and software configuration changes you want to make. Look specifically for conflicts with parts of the existing system configuration that are not being changed. =-=-=-=-=-=-=-=-=-=-= Command Line Options =-=-=-=-=-=-=-=-=-=-= The following table shows driver-specific command line options: NAME DEFINITION VALID DEFAULT VALUES VALUE ----------------------------------------------------------------------------- /MAXIMUMSGLIST = nnn Specify maximum number of 1 - 255 17 (type=REG_SZ) scatter-gather elements /MAXTAGS = nnn Specify tagged command 1 - 255 128 (type=REG_SZ) queue depth To enter driver-specific parameters, follow these steps: 1 Select Run from the File pull-down menu (Windows NT 3.5x), or Run from the Start button (Windows NT 4.0). 2 Type regedt32 and press ENTER. 3 Open the registry list to the following location: \HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\ aic78xx\Parameters\Device\DriverParameters If the \Parameters\Device\DriverParameters key already exists, skip to step 10 below to begin entering parameters. If the keys do not yet exist, you will need to create them by continuing with step 4. 4 Click on the aic78xx key. 5 Under the Edit pull-down menu, select Add Key. 6 Type Parameters as the name for the new key, and then press ENTER. 7 Click on the Parameters key. 8 Under the Edit pull-down menu, select Add Key. 9 Type Device as the name for the new key, and press ENTER. To specify a certain host adapter, append Device with the number of the host adapter. For example, type Device0 for the first host adapter, Device1 for the second, etc. If you omit the host adapter number, the configuration information applies to all 7800 Family host adapters. 10 Click on the Device key. 11 Under the Edit pull-down menu, select Add Value. 12 Type DriverParameters as the name for the new key, and then press ENTER. Make sure the Data Type is REG_SZ. 13 A String Editor text box will appear, enter parameters in the text box. When entering multiple parameters, each parameter must be separated by a space. =-=-=-=-=-=-=-=-=-= Diskette Contents =-=-=-=-=-=-=-=-=-= The following files are included in this diskette: o \DISK1 - Disk identifier file o \TXTSETUP.OEM - Install script used during NT installation o \WINNT\README.TXT - This file o \WINNT\3_5\AIC78XX.SYS - 7800 series driver v2.1x for Windows NT v3.5x o \WINNT\3_5\OEMSETUP.INF - Install script used by Windows NT Setup o \WINNT\4_0\AIC78XX.SYS - 7800 series driver v2.1x for Windows NT v4.0 o \WINNT\4_0\OEMSETUP.INF - Install script used by Windows NT Setup =-=-=-=-=-=-=-=-=-= Contacting Adaptec =-=-=-=-=-=-=-=-=-= Electronic Support ------------------ Technical information, including product literature, answers to commonly asked questions, information on software upgrades and other topics is available electronically through the following: o Adaptec World Wide Web (WWW) site at http://www.adaptec.com. o File Transfer Protocol (FTP) server at ftp.adaptec.com. o CompuServe Adaptec Forum at GO ADAPTEC. o Adaptec USA Bulletin Board Service (BBS) at 408-945-7727; supports up to 28,800 bps (bits per second), 8 data bits, 1 stop bit, no parity. No product literature is available on the Adaptec BBS. o Interactive Fax System at 408-957-7150; available 23 hours a day, 7 days a week. The fax system is out of service 1 hour each day. Technical and Product Support ----------------------------- o For technical support and information about many of AdaptecÆs electronic support services, call 800-959-SCSI (7274) or 408-945-2550, 24 hours a day, 7 days a week. o To use the Adaptec Interactive Support System, call 800-959-SCSI (7274) or 408-945-2550, 24 hours a day, 7 days a week. The system prompts you with questions regarding your problem and then provides step-by-step troubleshooting instructions. o To speak with a product support representative, call 408-934-SCSI (7274), M-F, 6:00 a.m. to 5:00 p.m., Pacific Time. After hours, on weekends, and on holidays, product support is also available for a fee at 800-416-8066. Sales and Ordering Information ------------------------------ o For sales information, call 800-442-SCSI (7274), M-F, 6:00 a.m. to 5:00 p.m., Pacific Time, or 408-945-8600 and ask for Inside Sales, M-F, 8:00 a.m. to 5:00 p.m., Pacific Time. o To order Adaptec software and SCSI cables, call 800-442-SCSI (7274), M-F, 6:00 a.m. to 5:00 p.m., Pacific Time. o To request additional documentation for Adaptec products, call 800-934-2766 or 510-732-3829, M-F, 6:00 a.m. to 5:00 p.m., Pacific Time.