IBM ThinkPad 600 Aug 26, 1998 System Program Service Diskette Version 1.03 ============================================ What This Diskette Does ----------------------- The System Program Service Diskette given here can update the system program stored in the ThinkPad system to fix problems, add new functions, or expand functions. The supported models are as follows. - ThinkPad 600 To determine if you have to update the system program or not, please refer to the "Summary of Change" section. To update the system program, please refer to the "Updating System Program" section. Released Version ---------------- Version 1.01 (Initial Release) Support for Windows 98 and fix for some problems Version 1.02 A fix for problems as noted below Version 1.03 A fix for problems as noted below Summary of Change ----------------- Key: Diskette Version (for example, 1.00 means Version 1.00) (New) New Function or Enhancement (Fix) Correction to existing function <1.01> - (New) Support for Windows 98. - (Fix) Serial mouse is not working on resume from hibernation. - (Fix) System hang-up upon creating a hibernation file.(only OS/2-HPFS). - (Fix) Hot Key Volume Default Value was changed from 2 to 4. - (Fix) POST174 error when docking to 1st docking station then 2nd docking station. This error occurs when 2nd docking station has IDE hard disk in it, and it is enabled by 3rd IDE channel using IRQ 11. - (Fix) TP600 docked SelectaDock III does not come up HDD indicator. - (Fix) The workaround for the cardbus card which does not support clock run protocol is implemented. <1.02> - (Fix) Support security function for HDD (HDD password) which is in the docking station. - (Fix) After the network card is installed, when user closes/opens the LCD, a blank screen appears on NT. - (Fix) 217/93/9210 error (unexpected result of drive diag) occurs on slim DVD drive in Easy-Seup Test. - (Fix) ACPI Revision update - (Fix) IDE device is not detected after you hibernate the thinkpad and cold dock it to the docking station - (Fix) If the user presses the power button while the system is in the LCD off state, no warning beep sounds. - (Fix) Password can not be input, when the system is put into standby mode (rahter than suspend) by the suspend timer function when attached to a docking station. - (Fix) When the power on password is set in Windows98 and the system is put into standby mode (rather than suspend) by other conditions, the password icon screen comes up by a key input after the screen goes blank by the screen timer off function. - (Fix) Hang at the updating Windows95 screen when installing Windows95 in some cases. - (New) Support LS120 in UltraslimBay. (Notice) It is highly recommended to update the following video driver along with this system program update. ThinkPad Video Features Diskette III for Windows 95 Version 6.14.00Q or later. <1.03> - (Fix) ROM Diagnostics for PCMCIA displays interrupt error(ErrCode 8020) at some CD-ROM Drive installed. Updating System Program ----------------------- Notes: - You need an AC adapter and a charged battery pack to update the system program. - If your computer is attached to any kinds of Docking station or port replicator, turn off the computer and detach it before proceeding. 1. Print these instructions or display on another computer. 2. Firmly connect the AC adapter to the computer. 3. Insert the System Program Service Diskette into the diskette drive and turn on the computer. 4. Select "Read this first..." from the menu and carefully read the information that appears. 5. Press the Esc key to return to the menu. 6. Select "Update system program" and follow the instruction on the screen. Warning: Do not turn off or suspend the computer until the update has been completed. IF YOU TURN OFF OR SUSPEND THE COMPUTER WHILE THE UPDATE IS STILL IN PROGRESS, THE SYSTEM BOARD MAY HAVE TO BE REPLACED. After the update has been completed, do the following to make the changes effective. 7. Make sure the System Program Service Diskette is removed from the diskette drive, then turn off the computer. 8. Press and hold the F1 key, then turn on the computer. Hold the F1 key until the Easy-Setup menu appears. 9. If a password prompt appears, type the correct password. 10. Select Config, then select Initialize. 11. Select OK to initialize the system. Run the diagnostics to make sure that the computer runs with no errors: 12. Turn off the computer, press and hold the F1 key, then turn on the computer. Hold the F1 key until the Easy-Setup menu appears. 13. Select Test, then select Start to run all the basic tests. Various test patterns will appear on the screen. An OK will appear for each device that passes the test. 14. Verify that OK appears for all of the devices tested. 15. Press the Esc key to exit Test and turn off the computer. System Program Information -------------------------- Each version of the System Program Service Diskette contains the following system program (BIOS). The BIOS P/N and the date can be viewed by invoking Easy-Setup and selecting Config followed by System Board. Diskette Diskette BIOS BIOS Version Name P/N Date -------- -------- ------- -------- 1.01 IBUJ02US 97H4112 06-23-98 1.02 IBUJ03US 97H4134 08-07-98 1.03 IBUJ04US 97H4135 08-21-98 Service Information ------------------- The System Program Service diskette installs System Program as follows. Reserved Usable ThinkPad Model BIOS P/N Date BIOS Area* BIOS ROM Area* --------------------------------------------------------------------- 600 97H4135 08/21/98 C0000-C9FFF E0000-EFFFF F0000-FFFFF * NOTE: - Memory Range C0000-C9FFF is reserved for Video BIOS. - Memory Range E0000-EFFFF can be used as UMB (Upper Memory Block) by a memory manager such as EMM386.EXE. - Memory Range F0000-FFFFF is reserved for BIOS. The BIOS P/N and the date can be viewed by invoking Easy-Setup menu. Simple Boot Flag function ------------------------- This function automatically optimizes the behavior and boot performance of the BIOS and operating system, based on the installed operating system and previous boot. If this function is Enabled and once a Plug and Play-capable operating system, such as Windows 98., is installed, the system BIOS does not configure such hardware resources as system interruptions, memory windows, and I/O port ranges for all the devices in the system. If you are going to use a non-Plug and Play-capable operating system, disable this function so that the BIOS will configure hardware resources. (Important Notice) If you use Windows95/98 and the other OSs(other than Winddows95/98) on the same system, you are required to set this Simple Boot Flag to disable using Easy-Setup every time to boot OSs other than Windows95/98. Simple Boot Flag can be set in Quick Boot which can be reached in Config icon in Easy-Setup. Trademarks ---------- * IBM and ThinkPad are trademarks of IBM Corporation in the United States. * Windows is a trademark of Microsoft Corporation.