ThinkPad X40 December 25, 2006 System Program Service Diskette BIOS Version : 2.08 (1UETD3WW) ====================================================================== Notice: ------- - This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher). Please get an additional package, Embedded Controller Program Version 1.12 (or higher), and update Embedded Controller Program in the system with it if necessary. - Embedded Controller Program Version 1.32 (or higher) is required for Intel Pentium M Processor 738/758/778/733 models. - BIOS Version 1.42 (or higher) is required for Intel Pentium M Processor 738 models. - BIOS Version 1.55 (or higher) is required for Intel Pentium M Processor 758/733 models. - BIOS Version 2.02 (or higher) is required for Intel Pentium M Processor 778 models. - If you should update Embedded Controller Program as well as the BIOS, update BIOS first. - This program is language independent and can be used with any language system. What This Diskette Does ----------------------- This System Program Service Diskette updates the system program (BIOS) stored in the ThinkPad system to fix problems, add new functions, or expand functions as noted below. This release supports the following system: - ThinkPad X40 To determine if you should update the system program, refer to the Summary of Changes section. To update the system program, refer to the Updating System Program (BIOS) section. Released Versions ----------------- Where: BIOS version (BIOS internal ID) 1.04 (1UET39WW) Initial Release for ThinkPad X40 1.05 (1UET40WW) Problem fixes 1.13 (1UET62WW) Problem fixes and feature enhancements 1.14 (1UET63WW) Problem fixes and feature enhancements 1.20b (1UET72WW) Problem fixes and feature enhancements 1.21 (1UET73WW) Problem fixes 1.22 (1UET74WW) Feature enhancements 1.42 (1UET92WW) Feature enhancements 1.43 (1UET93WW) Problem fixes 1.44 (1UET94WW) Problem fixes 1.55 (1UETA5WW) Problem fixes and feature enhancements 1.65 (1UETB5WW) Problem fixes and feature enhancements 1.66 (1UETB6WW) Problem fixes 1.67 (1UETB7WW) Feature enhancements 2.02 (1UETC7WW) Problem fixes and feature enhancements 2.03 (1UETC8WW) Problem fixes 2.06 (1UETD1WW) Problem fixes and feature enhancements 2.07 (1UETD2WW) Problem fixes 2.08 (1UETD3WW) Problem fixes and feature enhancements Summary of Changes ------------------ Where: x.xx : BIOS version bbbbbbbb : BIOS internal ID which is for administrator purpose. (New) New Function or Enhancement (Fix) Correction to existing function <1.04 (1UET39WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.02 (or higher). - (New) Support for ThinkPad X40. <1.05 (1UET40WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.02 (or higher). - (Fix) Meaning of a SD card write protect notch is inversed. - (Fix) POST thermal sensor error is not displayed even if the system thermal sensor is not working. - (Fix) (Windows XP, Windows 2000) System hang may occur at attaching a system to UltraBase X4. <1.13 (1UET62WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher). - (New) Support for Active Protection System. Note: Embedded Controller Program:1.12(1UHT58WW) or higher and Active Protection System (APS) driver 1.20b or higher are required to enable Active Protection System. Please update Embedded Controller Program and driver if necessary. For more detail, please refer to release notes of Embedded Controller Program and Active Protection System driver. - (New) Support for MTM customization using a BIOS Update Utility. - (Fix) (Windows XP, Windows 2000) System hang may occur at attaching a system to UltraBase X4. <1.14 (1UET63WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher) - (Fix) (Windows NT4) BIOS password prompt at resume is not displayed to external monitor, when the external monitor is used as a display device. Video driver package version 4.03.1381.3757(1UD214WW) or higher is required to fix this issue. - (Fix) (Windows NT4) Screen corrupts after wakeup from hibernation mode if a display device is a LCD panel. To recover the screen, press Ctrl+Alt+F1 keys or perform suspend and resume. <1.20b (1UET72WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher). - (Fix) Infrared device may not be configured under DOS even if infrared is enabled in BIOS Setup. - (New) Support for the 1.3GHz CPU. This is applied to only models with the 1.3GHz CPU. <1.21 (1UET73WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher). - (Fix) System may hang when the ThinkPad is attached to the UltraBase X4 while the system is powered on. <1.22 (1UET74WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher). - (New) Add new items in BIOS Setup Utility menu to support new function of handling password after Hibernation wakeup. ("Timer Wake with Battery Operation" in "Power", "Require password after hibernate" in "Security"->"Password") <1.42 (1UET92WW)> Note: This BIOS version will only work with the Embedded Controller Program Version 1.12 (or higher). - (New) Support for new models based on the Intel Pentium M Processor 738. Note: ThinkPad models with the Intel Pentium M Processor 738 require the Embedded Controller Program Version 1.32 (or higher). - (New) Support for the new models based on the Intel Pentium M Processor 713. - (New) Support for the 11a/b/g Wireless LAN Mini PCI Adapter II. - (New) Added new items in the BIOS Setup Utility menu to support enabling and disabling the internal network device and the internal wireless network device. Note: The "Internal Network Device" and "Internal Wireless Device" options are found by clicking Config then click Network. <1.43 (1UET93WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher). - (Fix) The 11a/b/g Wireless LAN Mini-PCI Adapter with the old device driver (version 2.4.1.7 or lower) does not work with BIOS version 1.42 (1UET92WW). - (Fix) The computer may be immediately powered off at the password prompt screen after returning from hibernation if the Power-on Password is set and "Require password after hibernate" option in the BIOS Setup utility is set to enabled. - (Fix) The correct passphrase is not accepted at the passphrase prompt screen of the UVM (User Verification Manager) function of the Client Security Software after returning from standby mode if all of the following conditions are met: 1. "Timer Wake with Battery Operation" option in the BIOS Setup Utility is set to disabled. 2. In the Windows XP Power Options properties, both "System standby" and "System hibernates" for "Running on batteries" are set. The timer setting of "System hibernates" is longer than that of "System standby". 3. The computer is running on the battery. 4. The computer goes into standby mode by following the timer setting of the "System Standby" option, and then is in idling state longer than the time which is set in the "System hibernates" option. 5. Let the computer resume normal operation from standby mode. <1.44 (1UET94WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher). - (Fix) The clock frequency (speed) of CPU is not set to the highest speed in battery mode even if "Intel(R) SpeedStep technology" option of "Power" of "Config" in the "BIOS Setup Utility" menu is set to Enabled and its "Mode for Battery" option is set to "Maximum Performance". <1.55 (1UETA5WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher). - (Fix) "Access IBM" may be launched after resuming from hibernation State - (New) Support for new models based on the Intel Pentium M Processor 758. Note: ThinkPad models with the Intel Pentium M Processor 758 require the Embedded Controller Program Version 1.32 (or higher). - (New) Support for new models based on the Intel Pentium M Processor 733. Note: ThinkPad models with the Intel Pentium M Processor 733 require the Embedded Controller Program Version 1.32 (or higher). <1.65 (1UETB5WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher). - (Fix) Bluetooth LED may not be turned on/off by pressing Fn + F5 keys under non-ACPI operating system environment. - (Fix) Warning Beep may sound when you eject system from UltraBase X4 even though system is attached to UltraBase X4 with standby state. - (Fix) LCD display may be turned off after entering the secondary hard drive password. This symptom may appear on following condition: System with UltraBase X4 should be in standby mode and then attach secondary hard drive which has hard drive password. After attaching hard drive, System resumes from standby mode and password prompt appears and then enter password. LCD display may be turned off just after entering password. - (New) Support for ThinkPad X4 Dock. Note: BIOS and EasyEject Utility need to be updated before you attach the system to ThinkPad X4 Dock. EasyEject Utility needs to be 75U202WW or later. The guide is specified in the X4 Dock User's Guide (P/N 73P4525). <1.66 (1UETB6WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher). - (Fix) Operating system may not load from a bootable USB Memory Key which is attached to the USB port in the UltraBase X4. - (Fix) "Internal Network Option ROM" setting in the BIOS Setup Utility is not configured by using a Remote CMOS Update Utility. - (Fix) After removing and replacing the backup battery, Client Security Software may not be installed or the Security Chip test performed by PC Doctor(DOS) may fail. <1.67 (1UETB7WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher). - (New) Enhancement of security function on power-on: When hard drive password is set, regardless of other passwords settings, Wake On LAN from power off state does not work. <2.02 (1UETC7WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher). - (New) Added new item in the BIOS Setup Utility menu to support enabling and disabling the internal Bluetooth device. Note: The "Internal Bluetooth Device" option is found by clicking Config then click Network. - (New) Support for new models based on the Intel Pentium M Processor 778. Note: ThinkPad models with the Intel Pentium M Processor 778 require the Embedded Controller Program Version 1.32 (or higher). - (Fix) USB devices connected to UltraBase X4 or ThinkPad X4 Dock may not be recognized in Boot Menu by pressing F12 during POST. <2.03 (1UETC8WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher). - (Fix) With BIOS 1UETB7WW (Version 1.67) or later, system shutdowns on Wake On LAN with a Ultrabay Slim Second hard drive adapter, even if no password is set in the second hard drive. - (Fix) POST error appears on power-on, just after power off at BIOS password prompt with a USB floppy drive or USB hard drive. <2.06 (1UETD1WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher). - (Fix) The CardBus Controller register setting was fixed. - (Fix) The problem that happens in production line was fixed. - (Fix) Machine may hang up when boot device is changed in BIOS setup. - (Fix) Intel Pentium M Processor and Centrino logos displayed on screen during POST were updated. - (Fix) POST hang may be caused when damaged HDD is attached. - (New) Added new item "ThinkPad NumLock" in the BIOS Setup Utility menu. It's found by clicking Config then click Keyboard/Mouse. If you select "Independent", NumLock on the ThinkPad computer can be disabled independently regardless of the NumLock state of the external keyboard. If NumLock on the ThinkPad computer is enabled, NumLock on the external keyboard will also be enabled. If you select "Synchronized", NumLock on the ThinkPad computer and NumLock on the external keyboard are synchronized. Note: "ThinkPad NumLock" menu item is available only when the Embedded Controller Program (H8 controller firmware) is also updated to version 1.61 (1UHTB1WW) or later. <2.07 (1UETD2WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher). - (Fix) If Windows 2000, XP video driver package version 6.14.10.3943 (1UD164WW) or higher is installed, the LCD brightness setting may be changed after wakeup from standby mode. <2.08 (1UETD3WW)> Note: This BIOS version will only work with Embedded Controller Program Version 1.12 (or higher). - (New) Support for Microsoft Windows Vista. - (Fix) CGA font characters are not displayed on the screen with programs for DOS. Updating System Program (BIOS) ------------------------------ Notes: - Remove the Power-on password prior to updating the system program (BIOS) in RDM (Remote Deployment Manager) environment or similar environment. - You need an AC adapter and a charged battery pack to update the system program (BIOS). - Make sure the System Program Service Diskette is write-protected. 1. Print these instructions or display on another computer. 2. Firmly connect the AC adapter to the computer. 3. Insert the write protected System Program Service Diskette into the diskette drive and turn on the computer. 4. Select Read this first from the menu and carefully read the information that appears. 5. Press the Esc key to return to the menu. 6. Select Update system program and follow the instructions on the screen. Note: If you are updating the system program through the USB external diskette drive, it will take quite a long time to complete reading the system program file, but it is normal. Continue the update. Attention: Do not turn off, suspend the computer or remove the diskette until the update has been completed. IF YOU TURN OFF OR SUSPEND THE COMPUTER WHILE THE UPDATE IS STILL IN PROGRESS, THE SYSTEM BOARD MAY HAVE TO BE REPLACED. After the update has been completed, the system is automatically turned off. Initializing System Program (BIOS) ---------------------------------- In some cases, it may be a good idea to try BIOS initialization when you have some troubles. To initialize the BIOS settings: 1. Turn off the computer. 2. Make sure there is no diskette in the diskette drive. 3. Turn on the computer. 4. While the "To interrupt normal startup, press the blue Access IBM button" message is displayed at the lower-left area of the screen, press the F1 key. The BIOS Setup Utility menu will be displayed. If a password prompt appears, type the correct password. 5. Press F9 key to load default configuration. 6. Select Yes. 7. Press F10 key to save default configuration and exit. 8. Select Yes. After the initialization has been completed, the system restarts automatically. BIOS Information ---------------- Each version of the System Program Service Diskette contains the following BIOS. Also the supported versions of Embedded Controller Program are shown below. The versions of BIOS and Embedded Controller Program can be viewed by entering the BIOS Setup Utility. BIOS Version Embedded Controller (Internal ID) Program Version ---------------- ------------------- 1.04 (1UET39WW) 1.02 (or higher) 1.05 (1UET40WW) 1.02 (or higher) 1.13 (1UET62WW) 1.12 (or higher) 1.14 (1UET63WW) 1.12 (or higher) 1.20b (1UET72WW) 1.12 (or higher) 1.21 (1UET73WW) 1.12 (or higher) 1.22 (1UET74WW) 1.12 (or higher) 1.42 (1UET92WW) 1.12 (or higher) (*1) 1.43 (1UET93WW) 1.12 (or higher) (*1) 1.44 (1UET94WW) 1.12 (or higher) (*1) 1.55 (1UETA5WW) 1.12 (or higher) (*2) 1.65 (1UETB5WW) 1.12 (or higher) (*2) 1.66 (1UETB6WW) 1.12 (or higher) (*2) 1.67 (1UETB7WW) 1.12 (or higher) (*2) 2.02 (1UETC7WW) 1.12 (or higher) (*3) 2.03 (1UETC8WW) 1.12 (or higher) (*3) 2.06 (1UETD1WW) 1.12 (or higher) (*3) 2.07 (1UETD2WW) 1.12 (or higher) (*3) 2.08 (1UETD3WW) 1.12 (or higher) (*3) Notes for Embedded Controller Program Version *1: 1.32 or higher for Intel Pentium M Processor 738 model *2: 1.32 or higher for Intel Pentium M Processor 738/758/733 models *3: 1.32 or higher for Intel Pentium M Processor 738/758/778/733 models To enter the BIOS Setup Utility: 1. Turn off the computer. 2. Turn on the computer. 3. While the "To interrupt normal startup, press the blue Access IBM button" message is displayed at the lower-left area of the screen, press the F1 key. The BIOS Setup Utility menu will be displayed. If a password prompt appears, type the correct password. 4. Check BIOS Version and Embedded Controller Version. 5. Turn off the computer. Memory Map Information ---------------------- Reserved Area: The following conventional memory addresses are reserved by the system program (BIOS) and others. C0000-CFFFF : Reserved for Video BIOS D0000-D3FFF : Reserved for Option ROM of Ethernet (*4) DC000-DFFFF : Reserved for USB BIOS (*5) E0000-FFFFF : Reserved for System BIOS Notes: *4: This area becomes free by disabling the Internal Network Option ROM option under Config and Network in the BIOS Setup Utility. *5: This area becomes free by disabling the USB BIOS Support option under Config and USB in the BIOS Setup Utility. Usable Area: The following memory address can be used by the memory manager such as EMM386. D4000-DBFFF But certain addresses in this area will be reserved for CardBus Controllers or others by Operating Systems. The addresses vary and depend on the design of each Operating System. Restrictions ------------ Passwords can be set with the passphrase feature, however, that feature is supported by Windows 2000 and Windows XP only. Trademarks ---------- * ThinkPad is registered trademark of Lenovo in the United States. * IBM and OS/2 are registered trademarks of IBM Corporation. * Intel, Pentium and Centrino are registered trademarks of Intel Corporation. * Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation. * Windows Vista is a trademark of Microsoft Corporation. Other company, product, and service names may be registered trademarks, trademarks or service marks of others.