Model M Keyboard Adapter Box
Constructed and described by Ron Bean firstname.lastname@example.org
Figure 1: Model-M Keyboard adapter box
This was inspired by John Szybowski's keyboard page. Instead of modifying a cable, I put the parts in a separate box so I wouldn't have to worry about strain relief-- if anything happens to the cable I can just replace it without re-doing all of the soldering. In theory this will just sit on the floor behind my desk, but you never know what might happen...
The small-order handling fee increases the cost by 50%, so it would help a lot if you could order at least $15 worth of other stuff at the same time (their catalog has over 1200 pages, there must be something else you need :-). Note that a PS/2 extension cable purchased locally costs $10, so the cost of this project is really not excessive.
Digi-Key ships worldwide, but there is an additional $6.00 handling fee for orders going outside the US and Canada. The good news is that if you're in the US or Canada and pre-pay with a check or money order, they won't charge you for shipping (there is a PDF order form on their website that you can print out and mail in).
Note that the Male-Male PS/2 cable is probably not a stock
item at your
local computer store, so be sure to order one (I've never seen a male
panel-mount PS/2 connector, so the more common male-female extension
Figure 2: PS/2 connectors
Digi-Key lists three kinds of panel-mount PS/2 connectors: one metal, one plastic, and one with wire pigtails. I recommend the plastic one, because I ended up drilling out the mounting holes to take standard 6-32 machine screws (smaller screws may be stock items in the electronics industry, but I didn't have any).
I'm not sure if the metal one was intended to be mounted with
on the front or the back of the panel. If you mount it on the front,
the little plastic tabs around the base would require a rather large
mounting hole, unless you want to file them off (the plastic one also
these tabs, but the mounting flange is molded around them). If you
it on the back, you would have to pay attention to the thickness of the
panel and the diameter of the plug. The plastic one is made to mount
behind the panel.
Figure 3: Layout for mounting holes
Figure 4: Pilot holes drilled
Figure 5: Main mounting holes drilled
Be careful drilling soft plastic with large twist drills-- they like to "grab" and the holes may not come out perfectly round. I cleaned them up with a handheld taper-reamer (available at many hardware stores, a good investment if you don't have one). For the screw holes I just used an oversized drill bit (5/32").
Figure 6: Sockets taped in place
I taped the sockets in place and drilled through the mounting flange and panel at the same time. For each socket, I dropped a screw into the first hole before drilling the second one, just to make sure nothing moved. Wiring will be easier if you mount both sockets facing the same direction.
Figure 7: Sockets bolted in place
Figure 8: Wiring in place
It's been a while since I soldered anything, so I used the extra metal socket shown above for practice. Fortunately, the electrons don't care what it looks like. I connected a resistor from +5v to the clock line on one connector, and from +5v to the data line on the other one, so no pin had more than two wires on it. Even then, it gets crowded. It helps to use thin solder that melts as soon as the joint is warm. The crud on the back of the socket is flux from the rosin-core solder.
IBM "M" Keyboard Modification for use with .
modern PC PS/2 ports .
+5V 4 o---o----o---------> red .
| | .
+++ +++ .
| | | | 4K7 Ohm .
| | | | to .
+++ +++ 10 KOHm .
| | .
KBCLOCK 5 o---o----+---------> green .
KBDATA 1 o--------o---------> yellow .
GND 3 O------------------> black .
PS/2 Plug To Keyboard .
6 x U o 5 .
4 o | o 3 .
2 x o 1 .
Mini-DIN Plug .
(rear side view on the solder pins) .
x-marked pins are N.C. or missing .
The colors noted are taken from a Non-IBM .
keyboard with a fixed cable, which is from .
the technical aspect like a "M" keyboard. .
This ASCII-Art: (C) 2010 by Peter H. Wendt .