Error Codes (2140, 2142)

  Error Codes (2140, 2142)

Error Codes	FRU/Action
107 System board, processor	1. Flash BIOS
update error. (A-2 system board only)	2. System Board
10X System board error or	1. System Board
continuous beep.
110 System board parity error	1. see 'Memory'
	2. DIMMs
	3. System Board
111 I/O channel parity error	1. see 'Memory'
	2. I/O channel memory
	3. System Board
114 External ROM checksum error	1. Adapter Card
	2. System Board
129 Cache memory error	1. see 'Memory'
	2. For A-1 system board:
	° System Board
	For A-2 system board:
	° Processor
12X Processor error	1. Run the Setup Utility, see
	'POST Error Codes'
	2. Processor
	3. System Board
13X System board error.	1. Run the Setup Utility, see
	'POST Error Codes'
	2. Processor
	3. System Board
151 Real-time clock failure	1. System Board
161 Low CMOS battery	1. CMOS clock/battery (if less than 2.8 Vdc)
	2. Run the Setup Utility, see 'POST Error Codes'
	3. System Board
162 CMOS RAM error.	1. CMOS clock/battery (if less than 2.8 Vdc)
	2. Run the Setup Utility, see 'POST Error Codes'
	3. System Board
163 Real-time clock error.	1. Set date and time
	2. Run the Setup Utility, see 'POST Error Codes'
	3. CMOS clock/battery (if less than 2.8 Vdc)
	4. System Board
164 Memory size error.	1. see 'Memory'
	2. DIMMs
	3. System Board
1XX errors not listed above	1. System Board
20X Memory error.	1. see 'Memory'
	2. DIMMs
	3. System Board
262 DRAM parity config. error.	1. see 'Memory'
	2. Run the Setup Utility, see 'POST Error Codes'
	3. DIMMs
	4. System Board
305 System board	1. see 'Keyboard'
non-replaceable fuse can be blown	2. Keyboard
by a defective KBD, KBD-cable,	3. Keyboard connection/cable
or mouse. If you suspect one	4. Mouse
of these FRUs, replace it when	5. System Board
you replace the system board.
3XX Keyboard error	1. see 'Keyboard'
	2. Keyboard connection
	3. Keyboard
	4. Media Console (Type 2142)
	5. System Board
602 Invalid diskette boot record	1. Diskette media
	2. Diskette connection/cable
	3. Diskette drive
662 Diskette drive config. error	1. see Factory-Installed Drive Devices
	2. Diskette connection/cable
	3. Diskette drive
	4. Power supply
	5. System Board
7XX Math coprocessor error	1. see Diagnostics and Utilities Device Presence Test'
	2. Upgrade processor (check Setup Utility, and
	system board settings.)
	3. System Board
962 Parallel port conflict	1. Test using a wrap plug while running
	Diagnostics and Utilities
	2. see Diagnostics and Utilities Device Presence Test'
	3. Parallel adapter card, if installed
	4. System Board
11XX Serial port test errors	1. Test using a wrap plug while running
not listed above.	Diagnostics and Utilities
	2. see Diagnostics and Utilities Device Presence Test'
	3. Serial adapter card, if installed
	4. System Board
On the system board :	1. Hard Disk drive connection/cable/jumpers.
1780/1790 Hard Disk Drive 0	If an upgradable processor is installed, check that the
1781/1791 Hard Disk Drive 1	proper speed has been set.
1782/1792 Hard Disk Drive 2	(switches and Setup Utility). Speed should be a
or CD/DVD-ROM drive	multiple of the original processor speed.
1783/1793 Hard Disk Drive 3	Hard disk drive size set correctly in Setup Utility.
or CD/DVD-ROM drive	2. Hard disk drive
if Hard Disk Drive 2 installed.	3. System Board
17XX Hard disk drive error	1. see 'Factory-Installed Drive Devices'
(All 17XX errors not listed above)	2. Hard disk drive jumpers
	3. Hard disk drive connection/cable
	4. Hard disk drive
	5. System Board
	6. Power Supply
1800 PCI Error (IRQ not available)	A PCI adapter card has requested a hardware
	interrupt that is not available
	1. Choose ISA Legacy Resources from the Setup Utility
	main menu, and make sure the interrupt resources (IRQ)
	setting for ISA legacy adapter cards are correct. If the
	interrupt resources settings are not correct, change the
	settings. See 'Using the Setup Utility'
	2. If all interrupt are being used by ISA legacy adapter cards,
	you might need to remove an ISA card to make memory available
	to the PCI adapter card.
1801 PCI Error (ROM not available)	A PCI adapter card has requested memory resources
	that are not available
	1. Choose ISA Legacy Resources from the Setup Utility
	main menu, and make sure the memory resources settings
	for ISA legacy adapter cards are correct. If the memory
	resources settings are not correct, change the settings.
	2. If all memory resources are being used by ISA legacy adapter
	cards you might need to remove an ISA card to make memory
	available to the PCI adapter card.
1802 PCI Error	A PCI adapter card has requested an I/O address
(I/O address not available)	that is not available, or the PCI adapter card might
	be defective.
	1. Choose ISA Legacy Resources from the Setup Utility
	main menu, and make sure the I/O port resources (IRQ)
	settings for ISA legacy adapter cards are correct. If the
	I/O port resources settings are not correct, change the
	settings.
	2. If the I/O port resources settings are correct, the PCI
	adapter card might be defective.
1803 PCI Error	A PCI adapter card has requested a memory address
(memory above 1 MB not available)	that is not available, or the PCI adapter card might
	be defective.
	1. Choose ISA Legacy Resources from the Setup Utility
	main menu, and make sure the memory resources settings
	for ISA legacy adapter cards are correct. If the memory
	resources settings are not correct, change them.
	2. If the memory resources settings are correct, the PCI
	adapter card might be defective.
1804 PCI Error	A PCI adapter card has requested a memory address
(memory below 1 MB not available)	that is not available.
	1. Choose ISA Legacy Resources from the Setup Utility
	main menu, and make sure the memory resources settings
	for ISA legacy adapter cards are correct. If the settings
	are not correct, change the settings.
	2. If all memory resources are being used by ISA legacy adapter
	cards, you might need to remove an ISA card to make memory
	available to the PCI adapter card.
1805 PCI Error (ROM error).	1. Remove the PCI adapter card.
	2. Restart the computer without the card installed. If the computer
	restarts without an error, reinstall the card and restart the
	computer again.
	If the error reoccurs, the adapter might be defective.
1806 No more DMA channels available	1. Too many adapters installed.
2401 Monitor changing colors	1. Monitor
2462 Video configuration error	1. Video memory, if installed
	2. System Board
24XX Video/monitor error	1. see 'Monitor'
	2. Optional video memory
	3. System Board
	4. Monitor
5801 Media Console error	1. Check Media Console cable
	2. replace Media Console
5803 Keyboard error	1. see 'Keyboard'
attached to Media Console	2. Keyboard
5806 Diskette error	1. Check Diskette cable
attached to Media Console	2. Diskette
5859 CD/DVD-ROM error	1. Check CD/DVD-ROM drive cable
attached to Media Console	2. CD/DVD-ROM Drive
5862 Host Card error	1. Host Card
5886 Pointing device	1. Check Pointing device cable
attached to Media Console	2. Pointing device
5962 CD/DVD-ROM	1. see 'Factory-Installed Drive Devices'
configuration error (sound adapter	2. CD/DVD-ROM drive connections, cables, and jumpers
card driver works correctly).	3. CD/DVD/-ROM drive
	4. Power supply
	5. System Board
86XX Pointing device	1. see 'Mouse'
error or mouse does not work.	2. Pointing device connection/cable
card driver works correctly).	3. Pointing device
	4. System Board
I999030X	1. Possible hard disk drive problem
Hard disk reset/boot failed	2. see 'Hard Disk Drive Boot Error'
Any other error codes	see 'Undetermined Problem'