Numeric Error Codes (2615)

Symptom/Error	FRU/Action
200006 - Hard Drive Error	1. Check drive cable connection.
	2. Boot the computer from the diskette drive,
	back up the hard drive, then prep and format
	the hard drive.
	3. Replace hard drive.
	4. Replace video/power board.
200007 - Hard Drive Error	1. Check drive cable connection.
	2. Boot the computer from the diskette drive,
	back up the hard drive, then prep and format
	the hard drive.
	3. Replace hard drive.
	4. Replace video/power board.
200008 - Hard Drive Error	1. Check drive cable connection.
	2. Replace hard drive.
	3. Replace video/power board.
200009 - Hard Drive Error	1. Check drive cable connection.
	2. Reinstall the operating system on the hard disk.
	3. Boot the computer from the diskette drive,
	back up the hard drive, then prep and format
	the hard drive.
200102 - Diskette Error	1. Make sure diskette is properly formatted
	and inserted.
	2. Try a different diskette.
	3. Check all cable connections.
	4. Replace diskette drive.
	5. Replace video/power board.
200103 - Diskette Error	1. Make sure diskette is properly
	formatted and inserted.
	2. Try a different diskette.
	3. Check all cable connections.
	4. Replace diskette drive.
	5. Replace video/power board.
200104 - Diskette Error	1. Remove any non-system diskettes when
	powering on the computer.
	2. Make sure diskette has a bootable operating
	system on it.
200105 - Diskette Error	1. Reformat the diskette.
	2. Replace the diskette.
	3. Replace video/power board.
200110 - Floppy Drive Error	1. Make sure diskette is fully inserted
	into the drive.
	2. Make sure diskette is formatted.
	3. Try a different diskette.
	4. Replace diskette drive.
	5. Replace video/power board.
200112 - Floppy Drive Error	1. Check drive cable connection.
	2. Replace diskette drive.
	3. Replace video/power board.
	4. Replace system board.
200113 - Floppy Drive Error	1. Check drive cable connection.
	2. Replace diskette drive.
	3. Replace video/power board.
	4. Replace system board.
200301 - Memory Error	1. Power-off computer, wait 15 seconds,
	then power-on.
	2. If the message reappears, replace system board.
200302 - Memory Error	1. Power-off computer, wait 15 seconds,
	then power-on.
	2. If the message reappears, replace system board.
200303 - Memory Error	1. Power-off computer, wait 15 seconds,
	then power-on.
	2. Perform BIOS update.
	See 'BIOS Update Procedure'.
	3. Replace system board.
200304 - Memory Error	1. Replace system board.
200305 - Memory Error	1. Perform BIOS update.
	See 'BIOS Update Procedure'
	2. Replace system board.
200307 - Memory Error	1. Charge battery, re-enter configuration
	data in Setup, power-off computer,
	then power-on.
	2. Replace backup battery.
	3. Replace system board.
200308 - Memory Error	1. Make sure memory modules are properly
	seated in their sockets.
	2. Use Setup to confirm that the hardware
	configuration is correct.
	3. Run Advanced Diagnostics to determine
	what hardware is failing.
	4. Replace memory modules if errors
	are above 2MB.
	5. Replace system board if errors
	are below 2MB or if
	replacing memory modules did not help.
200351 - PMI Error	1. This message appears if an SVGA monitor
An SVGA monitor is required to run	was attached when the system entered
the application that is to be resumed.	suspend mode, but it was not found,
	when the system resumed.
	2. Attach an SVGA monitor before resuming.
200352 or 200353	1. Retry the operation after the computer is
- PMI Error	finished accessing the diskette drive.
200354 - PMI Error	1. Insert the diskette that was in the computer
	when it was rested.
200355 - PMI Error	1. Retry the operation after modem or
	serial port activity is finished.
	2. Replace system board.
200402, 200403,	1. Power-off computer, wait 15 seconds,
200404, 200405	then power-on.
- Memory Error	2. Replace system board.
200453 or 200459	1. Use the Setup program to reconfigure.
- Configuration Error	2. Replace backup battery.
This message is normal after	3. Replace system board.
backup battery replacement.
200456 - Configuration Error	1. Use the Setup program to verify
	extended RAM memory size matches
	memory installed.
	2. Ensure memory module is proper installed.
	3. Use Advanced Diagnostics to test extended memory.
	If you cannot boot computer, replace system board
	and retry.
	° If the tests identify an expansion memory
	module (memory above 2MB), replace it.
	° If the tests identify a problem in the
	memory below 2MB, replace system board.
200458 - Configuration Error	1. Use Setup program to reconfigure.
	2. Make sure the drive is bootable.
	3. Replace hard drive.
	4. Replace system board.
200552 - Error	1. Verify keyboard is properly connected.
	2. Replace keyboard.
	3. Replace system board.
200553 - Error	1. Recharge the battery pack.
	2. Replace battery pack.
	3. Replace video/power board.
200554 - Error	1. Replace battery pack.
	2. Replace video/power board.
200555 - Error	1. Reboot computer and
	enter the correct password.
200556 or 200557 - Error	1. Try another copy of the software, or have
	the customer contact the software
	manufacturer or dealer
	and report the problem.
	2. Power-off computer, wait 15 seconds,
	then power-on. If the message reappears,
	replace system board.
200558 - Error	1. Try another copy of the software, or have
	the customer contact the software
	manufacturer or dealer
	and report the problem.
	2. Power-off computer, make sure all external
	cable connections are secure, wait 15 seconds,
	and, then power-on. If the message reappears,
	replace system board.

---

Please see the LEGAL  -  Trademark notice.
Feel free - send a   for any BUG on this page found - Thank you.