Before replacing any SCSI FRUs:
Before replacing any SCSI FRUs:
| Symptom/Error: | FRU/Action. |
|---|---|
| SCSI ID setting does not match the | 1. Device Switch Settings |
| SCSI ID shown in configuration. | 2. Device |
| 3. Device Cable | |
| 4. System Board | |
| Tape is autom. ejected from the | 1. Tape Cassette |
| drive. | 2. Drive |
| Tape sticks/breaks in the drive | 1. Tape Cassette |
| (Verify that the tapes used meet | |
| ANSI standard X3B5) | |
| 0XXX0730 | 1. Device ID Conflict, check |
| device and controller configuration. | |
| 00370830 | 1. System Board |
| NOTE: SCSI Circuit Breaker Error - | |
| Allow up to 15 minutes for the breaker to | |
| reset then rerun the test. If the error code | |
| persists, disconnect the internal and external | |
| SCSI cables, allow breaker to reset, and | |
| rerun the test again. If the error code persists | |
| replace the system board. | |
| 2. SCSI Cable | |
| 3. SCSI Device | |
| 00370850 | 1. System Board |
| 00370860 | 1. System Board |
| 0037XXXX | 1. SCSI Device |
| 2. SCSI Cable | |
| 3. System Board | |
| NOTE: Review 'SCSI Error Code Format' | |
| 0208XXXX | 1. Disconnect SCSI devices one |
| at a time to isolate problem. | |
| see Missing SCSI Devices | |
| 2. If problem remains with no SCSI devices | |
| attached, replace system board. | |
| 0209XXXX | 1. Removable Media |
| 2. SCSI DASD Device | |
| 3. Device Cables | |
| 4. System Board | |
| 0210XXXX | 1. SCSI Hard Disk Drive |
| (See 'SCSI FRU Codes' before replacing | 2. SCSI Cable |
| A FRU. If it is an external device, | 3. System Board |
| check the external voltages before | |
| replacing a FRU.) | |
| 0211XXXX | 1. Check media, clean tape drive, |
| (check for the two symptoms listed | try new media |
| below. Or, if it is an external drive, | 2. Tape Drive |
| and the power on LED is off, | 3. SCSI Cable (internal) |
| check the external voltages) | 4. System Board |
| Amber LED remains on. | 1. Check media, clean tape drive, |
| try new media | |
| 2. Tape Drive | |
| 3. SCSI Cable (internal) | |
| 4. System Board | |
| Green 'in use' LED fails to come on | 1. Check media, clean tape drive, |
| try new media | |
| 2. Tape Drive | |
| 3. SCSI Cable (internal) | |
| SCSI Cable (external) | |
| 4. System Board | |
| 0212XXXX | 1. SCSI Printer |
| 2. Printer Cable | |
| 0213XXXX | 1. SCSI Processor |
| 0214XXXX | 1. Check media presence, |
| try new media | |
| 2. WORM Drive | |
| 0215XXXX | 1. Check media presence, try |
| (Check 'Audio Symptoms' and also | new media. |
| see 'SCSI FRU Codes' before replacing | 2. CD-ROM Drive |
| a FRU. If it is an external device, | 3. SCSI Cable |
| and the power on LED is off, | 4. System Board |
| check external voltages before | |
| replacing a FRU.) | |
| 0216XXXX | 1. Scanner |
| 2. Cables | |
| 3. System Board | |
| 0217XXXX | 1. Check media presence, |
| (See 'SCSI FRU Codes' before replacing | write enabled, try new media |
| a FRU. If it is an external device, | 2. Rewritable Optical Drive |
| and the power on LED is off, check | 3. SCSI Cable |
| external voltages before replacing | 4. Removable Media |
| a FRU. | 5. System Board |
| 0218XXXX | 1. Check media presence, try |
| new media | |
| 2. Verify operation of attached media | |
| changer device, see service | |
| documentation for the failing device. | |
| 3. Media changing device, such as | |
| Multi disc Tray CD-ROM. | |
| 4. Cables | |
| 5. System Board | |
| 0219XXXX | 1. SCSI Communication Device |
| 2. Cables | |
| 3. System Board |
for any BUG on this page found - Thank you.