POST Error Codes - Netfinity 5600 - Type 8664

  POST Error Codes


In the following error codes, X can be any number or letter.

Error Code/Symptom	FRU/Action
062	1. Run Configuration/Setup
(Three consecutive boot	2. Battery/CMOS Chip
failures using the default	3. System Board
configuration.)
101, 102	1. System Board
(System and processor	2. Processor Board
error)
106	1. System Board
(System and processor	2. Processor Board
error)
111	1. Failing ISA Adapter
(Channel check error)	2. Memory DIMM
	3. System Board
114	1. Failing Adapter
(Adapter read-only memory	2. Run Diagnostics
error)
129	1. Processor
(Internal Cache error)	2. Optional Processor (if installed)
	3. Processor Board
151	1. Run Diagnostics
(Real time clock error)	2. Battery/CMOS chip
	3. System Board
161	1. Run Configuration/Setup
(Real time clock battery	2. Battery/CMOS chip
error)	3. System Board
162	1. Run Configuration/Setup
(Device Configuration Error)	2. Battery/CMOS Chip
- Important -	3. Failing Device
Be sure to load the	4. System Board
default settings and
any additional desired
settings, then, save
the configuration.
163	1. Run Configuration/Setup
(Real-Time Clock error)	2. Battery/CMOS Chip
	3. System Board
164	1. Run Configuration/Setup
(Memory configuration	2. DIMM
changed)	3. Processor Board
173	1. Run Configuration/Setup
(System CMOS checksum	2. Battery/CMOS Chip
bad)	3. System Board
175	1. System Board
(Hardware error)	2. Processor Board
176	1. Run Configuration/Setup
(Computer cover or cable	2. System Board
cover was removed without
a key being used)
177, 178	1. Run Configuration/Setup
(Security hardware error)	2. Service Processor Adapter
	3. System Board
184	1. Run Configuration/Setup
(Power-on password	2. System Board
corrupted)
185	1. Run Configuration/Setup
(Drive startup sequence	2. System Board
information corrupted)
186	1. Run Configuration/Setup
(Security hardware control	2. System Board
logic failed)
187	1. Set serial number in Setup
(VPD serial number not set.)	2. System Board
188	1. Run Configuration/Setup
(Bad EEPROM CRC #2)	2. System Board
189	1. Run Configuration/Setup, enter the administrator password
(An attempt was made to
access the server with
invalid passwords)
195	1. VRM 1
(Processor 1 is not	2. Processor 1
functioning)	3. Processor Board
	4. System Board
196	1. VRM 2
(Processor 2 is not	2. Processor 2
functioning)	3. Processor Board
	4. System Board
197	1. Processor 1
(Processor 1 failed BIST)	2. Processor Board
	3. System Board
198	1. Processor 2
(Processor 2 failed BIST)	2. Processor Board
	3. System Board
201	1. DIMM
(Memory test error)	2. Processor Board
	3. System Board
229	1. Processor
(Cache error)	2. Optional Processor (if installed)
	3. Processor Board
262	1. Run Configuration/Setup
(DRAM parity configuration	2. Battery/CMOS Chip
error)	3. System Board
289	1. Run Configuration/Setup, if disabled by user
(DIMM has been disabled	2. Ensure if a DIMM was added/changed that
by the user or system)	the power was disconnected.
	3. Disabled DIMM, if not disabled by user.
	4. Processor board
301	1. Keyboard
(Keyboard or keyboard	2. System Board
controller error)
303	1. Keyboard
(Keyboard controller error)	2. System Board
602	1. Diskette
(Invalid diskette boot record)	2. Cable
	3. Diskette Drive
604	1. Run Configuration/Setup and Diagnostics
(Diskette drive error)	2. Diskette Drive
	3. Drive Cable
	4. System Board
605	1. Diskette Drive
(Unlock failure)	2. Drive Cable
	3. System Board
662	1. Run Configuration/Setup and Diagnostics
(Diskette drive configuration	2. Diskette Drive
error)	3. Drive Cable
	4. System Board
762	1. Run Configuration/Setup
(Coprocessor configuration	2. Battery/CMOS Chip
error)	3. Processor
962	1. Disconnect external cable on parallel port.
(Parallel port error)	2. Run Configuration/Setup
	3. System Board
11XX	1. Disconnect external cable on serial port.
(System-board serial port 1	2. Run Configuration/Setup
or 2 error)	3. System Board
1301	1. Cable
(I2C cable to front panel	2. Front Panel
not found)	3. Power Switch Assembly
	4. System Board
1302	1. Cable
(I2C cable from system board	2. Power Switch Assembly
to power on and reset switches	3. System Board
not found)
1303	1. Cable
(I2C cable from system board	2. Power Backplane
to power backplane not found)	3. System Board
1304	1. Cable
(Cable to diagnostic LED
panel not detected)
1600, 1601	1. System Board
(The system is able to	2. Processor Board
communicate to the Service
Processor, but the Service
Processor failed to respond
at the start of POST.)
Do the following before
replacing a FRU:
1. Remove the AC power to
to the system, wait 20
seconds, then,
re-connect the AC power
Wait 30 seconds, then
power-on the system.
2. Flash update the
Service Processor.
3. Check the SP reset jumper
if fitted.
1762	1. Fixed Disk Cables
(Fixed Disk Configuration	2. Run Configuration/Setup
error)	3. Fixed Disk Adapter, if fitted
	4. Fixed Disk Drive
	5. System Board
178X	1. Fixed Disk Cables
(Fixed Disk error)	2. Run Diagnostics
	3. Fixed Disk Adapter
	4. Fixed Disk Drive
	5. System Board
1800	1. Run Configuration/Setup
(No more hardware interrupt	2. Failing Adapter
available for PCI adapter)	3. System Board
1801	1. Run Configuration/Setup
(No room for PCI option	2. Failing Adapter
ROM)	3. System Board
1802	1. Run Configuration/Setup
(No more I/O space	2. Failing Adapter
available for PCI adapter)	3. System Board
1803	1. Run Configuration/Setup
(No more memory (above	2. Failing Adapter
1MB for PCI adapter)	3. System Board
1804	1. Run Configuration/Setup
(No more memory (below	2. Move the failing adapter to slot 1 or 2
1MB for PCI adapter)	3. Failing Adapter
	4. System Board
1805	1. Remove Failing PCI Card
(PCI option ROM checksum	2. System Board
error)
1806	1. Run Configuration/Setup
(PCI to PCI Bridge error)	2. Move the failing adapter to slot 1 or 2
	3. Failing Adapter
	4. System Board
1807, 1808, 1810	1. Remove Failing PCI Card
(General PCI error)	2. System Board
1962	1. Verify a bootable operating system is installed
(Drive does not contain a	2. Run Diagnostics
valid boot sector)	3. Hard Disk Drive
	4. SCSI Backplane
	5. Cable
	6. System Board
2400	1. Video Adapter (if installed)
(Video controller test failure)	2. System Board
2462	1. Video Adapter (if installed)
(Video memory	2. System Board
configuration error)
5962	1. Run Configuration/Setup
(IDE CD-ROM configuration	2. CD-ROM Drive
error)	3. CD-ROM Power Cable
	4. IDE Cable
	5. System board
	6. Battery
8603	1. Pointing Device
(Pointing Device Error)	2. System Board
0001200	1. Processor
(Machine check architecture	2. Optional Processor
error)
000120P0,
000120P1, 000120P2, 000120PF	1. Failing Processor
(Processor cache error)	2. Processor Board
01295085	1. Processor
(ECC checking hardware	2. Processor Board
test error)
I9990301	1. Run Configuration/Setup for correct startup
(Fixed boot sector error,	2. Verify operating system installed
no operating system installed)
I9990305	1. Install operating system to hard disk drive.
(Fixed boot sector error, no
operating system installed)
I9990650	1. Check Cable
(AC power has been	2. Check for interruption of power supply
restored)	3. Power Cable