POST Error Codes


POST Error Codes
POST Error    FRU/Action
   Code/Symptom  
   101 1. System Board
   System board interrupt failure.  
   102 1. System Board
   System board timer error.  
   106 1. System Board
   110 1. Memory Module
   System board memory parity error. 2. System Board
   111 1. Reseat adapters
   I/O channel parity error. 2. Any Adapter
  3. System Board
   114 1. Adapter Memory
   Adapter ROM error. 2. System Board
   151 1. System Board
   Real-time clock failure.  
   161 1. Run Setup
   Bad CMOS battery. 2. CMOS Backup Battery
  3. System Board
   162 1. Run Setup and verify Configuration
   Configuration mismatch. 2. Had a device been added, removed, changed location?
      If not, suspect that device.
  3. Power-on external devices first, then power-on computer.
  4. CMOS Backup Battery
  5. System Board
   163 1. Time and Date Set?
   Clock not updating 2. CMOS Backup Battery
   or invalid time set. 3. System Board
   164 1. Run Setup. Check System Summary menu for memory size change.
   POST detected a base memory or 2. Run the Extended Memory Diagnostic tests.
   extended memory size mismatch error.  
   167 1. Update the Flash BIOS to the latest level
   Microprocessor installed that is not 2. Processor
   supported by the current POST/BIOS.  
   168 1. Run Setup. Check to see that Ethernet and Alert on LAN are enabled.
   Alert on LAN error 2. System Board
  3. Riser Card, if installed.
   175 1. Run Configuration
  2. System Board
   176 1. Covers were removed from the computer.
   177 1. System Board
   Corrupted  
   Administrator Password.  
   17X not listed above 1. C2 Security
   183 1. Enter the administrator password
   184 1. Make sure Asset Care and Asset ID are disabled in
   RFID Antenna Installed     Configuration/Setup. An RFID Antenna should not be installed.
   186 1. System Board
   187 1. Clear Administration password
  2. System Board
   18X not listed above 1. C2 Security
   190 1. System Board
   Chassis intrusion detector 2. Riser Card, if installed
   was cleared.  
   This is information only,  
   no action required.  
   If this code does not clear:  
   20X 1. Run Enhanced Diag. Memory Test
   Memory data error. 2. Memory Module
  3. System Board
   301 1. Keyboard
  2. Keyboard Cable
  3. System Board
   303 1. Mouse
   With an 8603 error. 2. Keyboard
  3. Keyboard Cable
  4. System Board
   303 1. Keyboard
   With no 8603 error. 2. Keyboard Cable
  3. System Board
   601 1. Diskette Drive A
  2. Diskette Drive Cable
  3. Riser Card, if installed
  4. System Board
   602 1. Bad Diskette
  2. Verify Diskette and retry.
   604 1. Run Setup and verify diskette configuration settings
  2. Diskette Drive A/B
  3. Diskette Drive Cable
  4. Riser Card if drive cable connected
  5. System Board
   662 1. Diskette drive configuration error or wrong diskette drive type,
      run Setup Configuration.
   762 1. Run Setup
   Math coprocessor 2. Processor
   configuration error. 3. System Board
   11XX 1. Serial Cable
   Serial port error 2. Serial device
  3. System Board
   1762 1. Run Configuration
   Hard disk drive  
   configuration error.  
   1780 (Disk Drive 0) 1. See Power Supply
   1781 (Disk Drive 1) 2. Hard Disk Drive
   1782 (Disk Drive 2) 3. Riser Card, if hard disk cable connected
   1783 (Disk Drive 3) 4. System Board
  5. Hard Disk Cable
  6. Power Supply
   180X, 188X 1. Run Setup and verify PCI/ISA configuration settings.
   PCI configuration 2. If necessary, set ISA adapters to 'Not available' to allow
   or resource error.     PCI adapters to properly configure.
  3. Remove any suspect ISA adapters.
  4. Rerun diagnostics.
  5. PCI Adapter
  6. PCI Riser Card
   1962 1. Run Configuration/Setup, check Boot Sequence.
   Boot sequence error. 2. Check cable connections.
  3. Run Diagnostics.
  4. Hard Disk Drive
  5. System Board
   2462 1. Check cable connections.
   Video memory configuration 2. Run Setup and verify video configuration settings.
   error. 3. Video Memory Modules
  4. Video Adapter (if installed)
  5. System Board
   5962 1. Run Configuration
   An IDE device (other than 2. CD-ROM Drive
   hard drive) configuration 3. CD-ROM Adapter
   error. 4. ZIP or other ATAPI device
  5. System Board
   8601, 8602 1. Pointing Device (Mouse)
  2. System Board
   8603, 8604 1. System Board
  2. Pointing Device (Mouse)
   86XX 1. Mouse
   Not listed above 2. System Board
   I999030X    Possible hard disk drive problem
   Hard disk reset failure  
   Error not listed above    Follow the instructions on the screen


Please see the LEGAL  -  Trademark notice.
Feel free - send a Email-NOTE  for any BUG on this page found - Thank you.