| Error Message | FRU/Action |
|---|---|
| 050: The board cannot be found | 1. Verify that the adapter is properly installed |
| The driver assumes that the adapter | 2. 10Base-t or 10Base2 Adapter |
| has not been installed. | |
| 058: The board does not respond | 1. Restart the computer or run the system |
| 070: The board has failed | configuration program to check for |
| The driver cannot communicate | possible system conflicts |
| with the adapter. | 2. 10Base-t or 10Base2 Adapter |
| 073: Unable to allocate memory | 1. Unload the driver and unnecessary NLMs |
| The driver was not able to | and try again |
| allocate sufficient memory to | 2. Reload the server and try again |
| perform its function | 3. Install additional memory into the server |
| 110: Unable to download the firmware | 1. Restart the computer or run the system |
| The driver is not able to | configuration program to check for possible |
| communicate with the adapter | system conflicts. |
| 2. 10Base-T or 10Base2 adapter | |
| 203: Board diags failed to complete | 1. Restart the computer or run the system |
| The driver is not able to communicate | configuration program to check for |
| with the adapter. | possible system conflicts |
| 2. 10Base-T or 10Base2 adapter. | |
| 301: POST Flash Main | 1. 10Base-T or 10Base2 adapter |
| Sector Checksum Failure | |
| 302: POST was not | |
| performed - board | |
| 303: POST Test | |
| Sequencer Internal Failure | |
| 304: POST Flash Boot | |
| Sector Checksum | |
| 305: POST DRAM Size | 1. Verif proper seating of the DRAM SIMM |
| Detection Failure | on the adapter. |
| The power unit is down | 2. 10Base-T or 10Base2 adapter |
| 306: POST DRAM Byte | 1. Verify proper seating of the DRAM SIMM |
| (8-bit) Wide Failure | on the adapter |
| 307: POST DRAM Short | 2. 10Base-T or 10Base2 adapter |
| (16-bit) Wide Failure | |
| 308: POST DRAM Word | |
| (32-bit) Wide Failure | |
| 309: POST DRAM Long | |
| (64-bit) Wide Failure | |
| 310: POST DRAM Trip | |
| (96-bit) Wide Failure | |
| 311: POST DRAM Quad | |
| (128-bit) Wide Failure | |
| 312: POST DRAM Quad | |
| Addressability Failure | |
| The power unit is down | |
| 313: SRAM Size Detection | 1. 10Base-T or 10Base2 adapter |
| Failure | |
| 314: SRAM Byte (8-bit) | |
| Wide Failure | |
| 315: SRAM Short (16-bit) | |
| Wide Failure | |
| 316: SRAM Word (32-bit) | |
| Wide Failure | |
| 317: SRAM Long (64-bit) | |
| Wide Failure | |
| 318: SRAM Trip (96-bit) | |
| Wide Failure | |
| 319: SRAM Quad (128-bit) | |
| Wide Failure | |
| 320: SRAM Addressability | |
| Failure | |
| 321: Timer Failure | |
| 322: Port 1 Internal | |
| Loopback Failure | |
| 323: Port 2 Internal | |
| Loopback Failure | |
| 324: Port 3 Internal | |
| Loopback Failure | |
| 325: Port 4 Internal | |
| Loopback Failure | |
| 326: Ethernet Port 1 | 1. Verify correct cabling of the port |
| Ext. Loopback Failure | 2. 10Base-T or 10Base2 adapter |
| 327: Ethernet Port 2 | |
| Ext. Loopback Failure | |
| 328: Ethernet Port 3 | |
| Ext. Loopback Failure | |
| 329: Ethernet Port 4 | |
| Ext. Loopback Failure | |
| 330: Port 1 Device | 1. 10Base-T or 10Base2 adapter |
| Verification Failure | |
| 331: Port 2 Device | |
| Verification Failure | |
| 332: Port 3 Device | |
| Verification Failure | |
| 333: Port 4 Device | |
| Verification Failure |
Please see the LEGAL - Trademark notice.
Feel free - send a
for any BUG on this page found - Thank you.