Numeric Error Codes
The following is a list of the message that the BIOS can display.
Most of them occur during POST. Some of them display information about a hardware device, e.g., the
amount of memory installed. Others may indicate a problem with a device, such as the way it has been configured.
Following the list are explanations of the messages and remedies for reported problems.
If the system fails after you make changes in the Setup menus, reset the computer, enter Setup
and install Setup defaults or correct the error.
 
 
 
   
 Symptom/Error 
     FRU/Action in Sequence 
   
    0200 
  1. Reseat hard disk drive. 
   
    Failure Fixed Disk 
  2. Load Setup Defaults in BIOS Setup Utility. 
   
   
  3. Hard disk drive 
   
   
  4. System board 
   
    0211 
     Go to 'Keyboard and Auxiliary Input Device Checkout'. 
   
    Stuck Key 
    
   
    0211 
     Go to 'Keyboard and Auxiliary Input Device Checkout'. 
   
    Keyboard error 
    
   
    0212 
     Go to 'Keyboard and Auxiliary Input Device Checkout'. 
   
    Keyboard Controller 
    
   
    Failed 
    
   
    0213 
     Unlock external keyboard. 
   
    Keyboard locked - 
    
   
    Unlock key switch 
    
   
    0220 
     Load Setup Defaults in BIOS Setup Utility. 
   
    Monitor type does not 
    
   
    match CMOS - Run Setup 
    
   
    0230 
     System board 
   
    Shadow RAM Failed 
    
   
    at offset:nnnn 
    
   
    0231 
  1. DIMM 
   
    System RAM Failed 
  2. System board 
   
    at offset:nnnn 
    
   
    0232 
  1. DIMM 
   
    Extended RAM Failed 
  2. System board 
   
    at offset:nnnn 
    
   
    0250 
     System board 
   
    System battery is dead 
    
   
    0251 
     System board 
   
    System CMOS checksum bad - 
    
   
    Default configuration used 
    
   
    0260 
  1. Run BIOS Setup Utility to reconfigure the system, 
   
    System timer error 
        then reboot the system. 
   
   
  2. System board 
   
    0270 
  1. Run BIOS Setup Utility to reconfigure the system, then reboot the system. 
   
    Real time clock error 
  2. System board 
   
    0280 
  1. Load Setup Defaults in the BIOS Setup Utility. 
   
    Previous boot incomplete - 
  2. System board 
   
    Default configuration used 
    
   
    0281 
  1. Load Setup Defaults in the BIOS Setup Utility. 
   
    Memory size found by 
  2. DIMM 
   
    POST differed from CMOS 
  3. System board 
   
    02D0 
     System board 
   
    - Cache disabled 
    
   
    System cache error 
    
   
    02F0 
     System board 
   
    CPU ID: 
    
   
    02F5 
  1. DIMM 
   
    DMA Test Failed 
  2. System board 
   
    02F6 
  1. DIMM 
   
    Software NMI Failed 
  2. System board 
   
    02F7 
  1. DIMM 
   
    Fail-Safe Timer 
  2. System board 
   
   NMI Failed 
    
Please see the LEGAL  -  Trademark notice.
Feel free - send a  for any BUG on this page found - Thank you.
  for any BUG on this page found - Thank you.