CPC091792

                      The Complete FAX 9624
                        (MNP and Non-MNP)
               Instructions for Using Qmodem 5.0x
                                


This document is provided as "For your information" and as is.
Neither The Complete PC nor any of it's employees assume any
responsibility for consequences resulting from the use of the
following information nor can the Complete PC technical support
provide help with this document.  The user of said information
does so at his or her own risk.

                              Setup
                                
Start by executing QSM or press Alt-N if you are already in
Qmodem.  This will bring up the configuration menus.  Choose M
for modem.  Communications Parameters will be highlighted.  Press
the ENTER key to select it.  Check your default baud rate.  If
you have a Non-MNP modem, the value should be 2400.  If you have
an MNP modem the value should be 9600.  Press A if you need to
change the value shown.  Then move the highlight bar down the
list that appears to the appropriate rate and press the ENTER key
to select it.  That should bring you back to the Communication
Parameters menu  Next check your COM port listing on option J.
Be sure it set for the correct COM port for your modem.  If it is
not, press J to bring up a list of ports.  Move the highlight bar
to the appropriate port and press the ENTER key.  The port will
then be selected.  Press the ESC key to  return to the Modem
menu.

Next comes Modem Commands.  Press M to select it.  The first item
on the list will now be Initialization string.  Press the ENTER
key to select it.  Refer to the listing below to identify the
appropriate string for your Non-MNP or MNP modem.

Non MNP
Initialization string:   AT&F&C1&D2^M
Alternate:          ATE1V1Q0X4&C1&D2^M

MNP
Initialization string:   AT&F&C1&D2^M
Alternate:          AT&C1&D2E1V1Q0X4\A3\N3\Q3\V1%C1\J0^M

Remember to remove any extraneous characters in the field.  It
will place your modem in the mode set by the factory and will
generally give you the best performance.  If you find that your
modem does not quite respond properly to such, you may choose to
use the alternate.  This forces the modem to operate as a Hayes
compatible, a mode that Qmodem should find completely acceptable.
In the case of the MNP alternate, MNP modem users will be forcing
the MNP reliable mode on, thus achieving data compression and
error checking.
Once the appropriate string is entered, press the ENTER key to
log your changes.  Press H to select the hang-up string field.
The hang-up string for the Non-MNP and the MNP modems are the
same and should be listed as follows:

                             ATH0 ^M

Once this has been entered and all other extraneous characters
removed from the field, press ENTER to log your changes.

Press the ESC key to  return to the Modem menu.

Next press T for Toggles.  The first item on the list will be
Xon/Xoff flow.  If it is ON, press the ENTER key to turn it OFF.
Then press C to select CTS/RTS flow.  Press the ENTER key to turn
it ON.  Press the ESC key to  return to the Modem menu.

Press the ESC key again to  return to the main menu bar.

                       Host Mode Settings

The default settings in Qmodem for the host mode will suffice for
the most part.  Non-MNP modem users will not need to make any
changes to this.

MNP modem users will need to make a slight change to the
initialization string.  Press H to access the Host  menu.  Press
I to enable edit of the Initialization string.  The string should
read as follows:

Initialization string:   AT&F&C1&D2H0S0=0^M
Alternate:          AT&C1&D2E1V1Q0X4\A3\N3\Q3\V1%C1\J0H0S0=0^M

Once the string has been entered and all extraneous characters
removed from the field, the ENTER key to log your changes.
Press the ESC key to return to the main menu bar.

Press E at the main menu bar for Exit.  Then press S to save
changes.

Please refer to your QModem documentation for more information on
setup and use of QModem.