SEAGATE TECHNOLOGY, INC. 1-800-SEAGATE http://www.seagate.com (C)opyright 1996 ST-3543A, Filepro 540 AT (Cabo CFS540A) ÉÍÍÍÍÍÍÍÍÍÍÍ» º REAR VIEW º ÈÍÍÍÍÍÍÍÍÍÍͼ Optional Mini Power Power Connector J2 40 pin I/O Cable Connection ÚÄÁÄ¿ ³ G 5 ÕÍÍÍÍÍÍÍÍÍ ÍÍÍÍÍÍÍÍ͸ /ÄÄÄÄÄÄÄÄÄ\ TOP (HDA) ͵0 0 0Æ͵::::::::::ú::::::::1Æͳ 0 0 0 0 ³ÍÍ 12 ÔÍÍÍÍÍÍÍÍÍͳÍÍÍÍÍÍÍÍ; ÀÄ5ÄGÄGÄ12Ù BOTTOM ³ ÀÄÄÄ pin-20 removed ST-3543A ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º Front View º ÚÄÄÄÄ Compatibility Mode ÈÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ³ ATA ON, ISA OFF ³ ³ ÚÄÄ Master ON, Slave OFF (C/D) ³ ³ (TOP) o o o o o o o o1 Option Block ÍÍÍ o o o o o o o2ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ (BOTTOM) ÀÄÄÄÂÄÄÄÙ ³ ³ ³ Reserved ÄÄÄÙ ³ Cable Select ÄÄÄÄÄÄÙ ST-3543A Filepro 540 AT (Cabo CFS540A) FORMATTED CAPACITY _______________________541.9 ACTUATOR TYPE ____________________________VOICE COIL CYLINDERS __PHYSICAL______________________2574 HEADS ______PHYSICAL______________________4 DISCS (3.5 in) ___________________________2 MEDIA TYPE _______________________________THIN FILM HEAD TYPE ________________________________THIN FILM RECORDING METHOD _________________________ZBR RLL (1,7) INTERNAL TRANSFER RATE (Mbits/sec) _______23.5 to 35.3 EXTERNAL TRANSFER RATE (Mbytes/sec) ______up to 13 PIO MODE _________________________________3 DMA SUPPORT ______________________________EISA Type B SPINDLE SPEED (RPM) ______________________3600 AVERAGE LATENCY (mSEC) ___________________8.33 BUFFER ___________________________________64K Read/Write Multiple, Read Look-Ahead, Multi-Segmented INTERFACE ________________________________ATA SECTORS PER DRIVE (LBA mode) _____________ TPI (TRACKS PER INCH) ____________________2990 BPI (KBITS PER INCH) _____________________70K AVERAGE ACCESS (ms) ______________________<15 SINGLE TRACK SEEK (ms) ___________________3 MAX FULL SEEK (ms) _______________________24 MTBF (power-on hours) Office _____________250,000 SHOCK (G's): operating (Read/Write) __________5 abnormal ________________________ nonoperating ____________________75 ACOUSTICS (bels) (typ/max) _______________42/ POWER DISSIPATION (watts) ________________ POWER REQUIREMENTS: +12V START-UP (amps) _1.2 POWER MANAGEMENT (Watts): ACTIVE _______________5.6 IDLE _________________3.9 STANDBY ______________<1.0 WRITE PRECOMP (cyl) ______________________N/A REDUCED WRITE CURRENT (cyl) ______________N/A LANDING ZONE (cyl) _______________________AUTO IBM AT DRIVE TYPE ________________________* Physical: Height (inches/mm): 1.00/25.4 Width (inches/mm): 4.00/101.6 Depth (inches/mm): 5.75/146.1 Weight (lbs/kg): 1.25/0.57 * MAY REQUIRE FORMATTING AND PARTITIONING SOFTWARE. ALSO, CHECK TO SEE IF YOUR CMOS SETUP HAS A "CUSTOM" OR "USER DEFINABLE" DRIVE TYPE AVAILABLE. (see below) Possible translations: This translation is generally acceptable, as is, for non-DOS operating systems: 1050 cyl, 16 heads, 63 sectors = 541,900,800 DOS operating systems may require a system bios that accepts larger values for the CMOS head parameter which lowers cylinders below 1024: 525 cyl, 32 heads, 63 sectors = 541,900,800 Other FULL-CAPACITY solutions for DOS operating systems include third-party drive preparation software, system BIOS which supports LBA mode or bios driven host adapters. Otherwise, capacity may be limited to: 1024 cyl, 16 heads, 63 sectors = 528,482,304 Note: A "custom" or "user-definded" CMOS drivetype may ask for a numerical value for the Write Precompensation cylinder and for the Landing Zone cylinder. A basic rule-of-thumb for drive models that do not require the old Write Precomp technique or a Landing Zone because they are Auto-Parking is to add 1 to the cylinder value being used. As an example: If cylinders equaled 820, then both Write Precomp and Landing Zone would be entered as 821. Some BIOS will convert this to 65535 or -1, which are functionally equivalent to "none (not used)". Already low-level formatted at the factory. Since a User-definable or Custom translation geometry may be used, it is imperative that the values be written down and kept with your permanent records for retrieval in the event of CMOS battery failure. Seagate reserves the right to change, without notice, product offerings or specifications. (09/09/96)