SEAGATE TECHNOLOGY, INC. 1-800-SEAGATE http://www.seagate.com (C)opyright 1996 ST-32132A, Medalist 2132 AT ÉÍÍÍÍÍÍÍÍÍÍÍ» º REAR VIEW º ÈÍÍÍÍÍÍÍÍÍÍͼ J2 40 pin I/O Cable Connection ³ Ú Ä Spare jumper stored on pins 1-3 ³ ³ ÕÍÍÍÍÍÍÍÍÍ ÍÍÍÍÍÍÍÍÍÑÍÍÍÍÍ1Í/ÄÄÄÄÄÄÄÄÄ\ TOP (HDA) ͵::::::::::ú::::::::1³ : :Á: ³ 0 0 0 0 ³ÍÍ ÔÍÍÍÍÍÍÍÍÍͳÍÍÍÍÍÍÍÍÍÏͳͳͳÍÀÄ5ÄGÄGÄ12Ù BOTTOM ³ ³ ³ ³ pin-20 removed ÄÙ ³ ³ ÀÄÄ Diagnostics (when Master ON) ³ ÃÄÄÄÄ Slave Present (when Master ON) ³ ÀÄÄÄÄ Cable Select (when Slave OFF) ÀÄÄÄÄÄÄ Master ON, Slave OFF ST-32132A Medalist 2132 AT FORMATTED CAPACITY _______________________2113.41 ACTUATOR TYPE ____________________________VOICE COIL CYLINDERS __PHYSICAL______________________ HEADS ______PHYSICAL______________________6 DISCS (3.5 in) ___________________________3 MEDIA TYPE _______________________________THIN FILM HEAD TYPE ________________________________THIN FILM RECORDING METHOD _________________________ZBR PRML (0,12,8) INTERNAL TRANSFER RATE (Mbits/sec) _______35 to 68 EXTERNAL TRANSFER RATE (Mbytes/sec) ______up to 16.6 PIO MODE _________________________________4 DMA SUPPORT ______________________________EISA Type B SPINDLE SPEED (RPM) ______________________4504 AVERAGE LATENCY (mSEC) ___________________6.66 BUFFER ___________________________________128K Read/Write Multiple, Read Look-Ahead, Multi-Segmented INTERFACE ________________________________Fast ATA-3 SECTORS PER DRIVE (LBA mode) _____________4,127,760 TPI (TRACKS PER INCH) ____________________5435 BPI (KBITS PER INCH) _____________________89 AVERAGE ACCESS (ms) ______________________12.5 SINGLE TRACK SEEK (ms) ___________________2.5 MAX FULL SEEK (ms) _______________________30 MTBF (power-on hours) Office _____________300,000 SHOCK (G's): operating (Read/Write) __________2 abnormal ________________________ nonoperating ____________________75 ACOUSTICS (dBA) (typ/max) _______________30/ POWER DISSIPATION (watts) ________________ POWER REQUIREMENTS: +12V START-UP (amps) _1.31 POWER MANAGEMENT (Watts): ACTIVE _______________5.98 IDLE _________________3.24 STANDBY ______________0.84 WRITE PRECOMP (cyl) ______________________N/A REDUCED WRITE CURRENT (cyl) ______________N/A LANDING ZONE (cyl) _______________________AUTO IBM AT DRIVE TYPE ________________________* Physical: Height (inches/mm): 1.00/25.4 Width (inches/mm): 4.00/101.6 Depth (inches/mm): 5.75/146.1 Weight (lbs/kg): 1.25/0.57 * MAY REQUIRE FORMATTING AND PARTITIONING SOFTWARE. ALSO, CHECK TO SEE IF YOUR CMOS SETUP HAS A "CUSTOM" OR "USER DEFINABLE" DRIVE TYPE AVAILABLE. (see below) Possible translations: This translation is generally acceptable, as is, for non-DOS operating systems: 4095 cyl, 16 heads, 63 sectors = 2,113,413,120 DOS operating systems may require a translation that uses larger values for the CMOS head parameter which lowers cylinders below 1024: 1023 cyl, 64 heads, 63 sectors = 2,111,864,832 Other FULL-CAPACITY solutions for DOS operating systems include third-party drive preparation software, system BIOS which supports LBA mode or bios driven host adapters. Otherwise, capacity may be limited to: 1024 cyl, 16 heads, 63 sectors = 528,482,304 Note: A "custom" or "user-definded" CMOS drivetype may ask for a numerical value for the Write Precompensation cylinder and for the Landing Zone cylinder. A basic rule-of-thumb for drive models that do not require the old Write Precomp technique or a Landing Zone because they are Auto-Parking is to add 1 to the cylinder value being used. As an example: If cylinders equaled 820, then both Write Precomp and Landing Zone would be entered as 821. Some BIOS will convert this to 65535 or -1, which are functionally equivalent to "none (not used)". Already low-level formatted at the factory. Since a User-definable or Custom translation geometry may be used, it is imperative that the values be written down and kept with your permanent records for retrieval in the event of CMOS battery failure. Seagate reserves the right to change, without notice, product offerings or specifications. (02/03/97)