SEAGATE TECHNOLOGY, INC. 1-800-SEAGATE http://www.seagate.com (C)opyright 1991 ST-1239A (94354-239 or 230) Swift AT (IDE) ΪΔΔΔ\ ³ 0 ³ 5 ³ 0 ³ G ΪΔΏ Some have ³ 0 ³ G AT (IDE) Cable ³ ΓΔ these pins ³ 0 ³ 12 1Ϊ........................Ώ o o o o o(o o) 6 is OFF ΐΔΔΔ/ ........................ o o o o o(o o) 7 is ON ΝΝΝΝΝΝΝPΝWΝAΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝ 1 2 3 4 5 6 7 ON OFF ³ ³ ³ ³ ³ ΐΒΩ 1 Slave Master ΔΔΩ ³ ³ ³ ³ ³ 2 5 Heads 7/9 Heads ΔΔΔΔΩ ³ ³ ³ ³ 3 Slave installed Slave not inst. ΔΔΔΔΔΔΩ ³ ³ ³ 4 7 byte ECC 4 byte ECC ΔΔΔΔΔΔΔΔΩ ³ ³ 5 Factory test Normal Oper. ΔΔΔΔΔΔΔΔΔΔΩ ³ 6/7 Some PWA's have these pins, factory use ΔΔΔΔΔΔΔΩ SWIFT Shrouded AT Interface Connector Only ΪΔΔΔ\ ³ 0 ³ 5 ΪΔ If the AT Connector has a plastic shroud, note pin-1 ³ 0 ³ G ³ Ϊ Pin-20 missing for keying purposes ³ 0 ³ G ³ ³ ³ 0 ³ 12 ΥΝΝΝΝΝΝΝΝΝΨΝΝΝΝΝΝΝΝΝΝΈ o o o . o o ΐΔΔΔ/ ³:::::::::ω:::::::::1³ o o o . o o (Note: 8-pin jumper ΝΝΝΝPΝWΝAΝΟΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΟΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝ block on side of 1 2 3 4 5 6 drive for factory ON OFF ³ ³ ³ ³ ³ ³ use only.) 1 Slave Master ΔΔΩ ³ ³ ³ ³ ³ 2 Slave installed Slave not inst. ΔΔΔΔΩ ³ ³ ³ ³ 3 SPSYNC (spindle sync) on Pin-28 ΔΔΔΔΔΔΔΔΔΩ ³ ³ ³ 4 (pins removed) ΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΩ ³ ³ 5 Spare ΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΩ ³ 6 SPSYNC External Connection ΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΔΩ ST-1239A 94354-239 or 230 Swift UNFORMATTED CAPACITY (MB) ________________239 FORMATTED CAPACITY (36 SECTORS) (MB) _____211 ACTUATOR TYPE ____________________________VOICE COIL TRACKS ___________________________________11,448 CYLINDERS ________________________________1,272 HEADS ____________________________________9 DISCS ____________________________________5 MEDIA TYPE _______________________________THIN FILM RECORDING METHOD _________________________RLL (2,7) TRANSFER RATE (mbytes/sec) _______________1.25 SPINDLE SPEED (RPM) ______________________3,600 AVERAGE LATENCY (mSEC) ___________________8.33 BUFFER ___________________________________32 or 64 Kbyte Read Look-Ahead, Non-Adaptive, Single-Segmented INTERFACE ________________________________AT BUS SECTORS PER DRIVE ________________________412,128 TPI (TRACKS PER INCH) ____________________1,543 BPI (BITS PER INCH) ______________________28,103 AVERAGE ACCESS (ms) ______________________15 SINGLE TRACK SEEK (ms) ___________________4 MAX FULL SEEK (ms) _______________________35 MTBF (power-on hours) ____________________150,000 POWER REQUIREMENTS: +12V START-UP (amps) _2.5 +12V TYPICAL (amps) __0.7 +5V START-UP (amps) __0.75 +5V TYPICAL (amps) ___0.4 TYPICAL (watts) ______11 MAXIMUM (watts) ______33.75 BUFFERED STEP PULSE RATE (micro sec) _____6-200 WRITE PRECOMP (cyl) ______________________N/A REDUCED WRITE CURRENT (cyl) ______________N/A LANDING ZONE (cyl) _______________________AUTO PARK IBM AT DRIVE TYPE ________________________* * MAY REQUIRE FORMATTING AND PARTITIONING SOFTWARE. ALSO, CHECK TO SEE IF YOUR CMOS SETUP HAS A "CUSTOM" OR "USER DEFINABLE" DRIVE TYPE AVAILABLE. Possible Translation: 954 cyl, 12 heads, 36 sectors = 211,009,536 Possible Translation: 817 cyl, 14 heads, 36 sectors = 210,825,216 Possible Translation: 990 cyl, 16 heads, 26 sectors = 210,862,080 Note: A "custom" or "user-definded" CMOS drivetype may ask for a numerical value for the Write Precompensation cylinder and for the Landing Zone cylinder. A basic rule-of-thumb for drive models that do not require the old Write Precomp technique or a Landing Zone because they are Auto-Parking is to add 1 to the cylinder value being used. As an example: If cylinders equaled 820, then both Write Precomp and Landing Zone would be entered as 821. Some BIOS will convert this to 65535 or -1, which are functionally equivalent to "none (not used)". PHYSICAL/LOGICAL equivalent to NATIVE/TRANSLATION Already low-level formatted at the factory. Since a User-definable or Custom translation geometry may be used, it is imperative that the values be written down and kept with your permanent records for retrieval in the event of CMOS battery failure. Swift Remote LED Option Front View of Drive Without the Plastic Bezel ΪΔΔΔΒΔΔΔΏ ³ A ³ B ³ B = Anode ΓΔΔΔΕΔΔΔ΄ D = Cathode ³ C ³ D ³ ...ΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΟΝΝΝΟΝΝΝΟΝΝΝΝΝPΝWΝAΝΝΝ... ψ Default jumper at C-D for LED mounted on drive PWA ψ To use remote LED, remove jumper and extend B (Anode) and D (Cathode). ψ Swift LED kit 75912397 allows connection to a remote LED ψ Swift LED kit 95913369 has an LED for attachment to the system front bezel or a 5.25-inch frame kit Seagate reserves the right to change, without notice, product offerings or specifications. (6/26/90)