Need help setting up access to network printer.
Have a HP LaserJet 4+ attached via parallel port to a RS/6000 7012-250 running AIX 4.3.3.11/Netscape 4.8 that cannot handle Postscript sent to it by Netscape.Have a HP LaserJet 4500N on a P2P Workgroup that will. The RS/6000 is attached to the P2P network for it's internet connection.
Here is what I did.
Using smit installed the software for the HP LaserJet 4500N off CD3 
Using smit installed the software for the HP JetDirect Network Printer off CD3

The next procedure failed error "host name 192.168.0.109 not valid"
and "host name 131.181.153.109 not valid" see printer config below.
Using smit/print spooling/add a print queque
chose HP JetDirect
Chose HP
chose HP4500
chose Do NOT make this system a BOOTP/TFTP server
( my reasoning here was the printer is on a P2P network and did not want the RS/6000 to take control as this may preculde several Windows systems getting access to the printer which they already have)
Description  left as Hewlett_Packard Color LaserJet 4500 
( Can I alter this to 4500Dup as it is called in each Win Computer)
Names of New Print Queques
       PCL                    left field blank
       POSTSCRIPT             PSHP
       HP-GL/2                left field blank
Printer Connection Characteristics
   * Host Name of the JetDirect Card        192.168.0.109 ( tried again with 131.181.153.109)
     PORT           9100
From the RS\6000 I can ping 192.168.0.109 but cannot ping (nor could WinXP) 131.181.153.109
Reading the manuals, help and red books, they are very light on in specific detail.
I could not find my siuation Googling but gather smit will not write the correct lines in various files like
/etc/hostlpd         my file is empty
/etc/hostsequiv      my file is empty
/etc/hosts           127.0.0.1 loopback local host
                     192.168.0.166   oldage  this is my RS/6000 computer
/etc/qconfig          HP4PCL:   device=lp0
                      lp0:      file = /dev/lp0
                                header = never
                                trailer = never
                                access = both
                                backend = /usr/lib/lpd/piobe
In this last file only my HP LaserJet 4+ is mentioned attached to the parallel port.
Smit supported printers show 4+ and 4500
Smit defined printers only shows the 4+. I presume this is because the 4500 queque is not set up.
Here is the 4500 printer configuration print out

EIO ColorLasetJet 4500 Configuration

JetDirect Configuration Page

GENERAL INFORMATION

HP JETDIRECT J3113A
FIRMWARE REVISION: G.08.04
LAN HW ADDRESS:, 001083A109EB
PORT SELECT: RJ45
PORT CONFIG: 100TX HALF
AUTO NEGOTIATION: ON
MFG ID: 39423942900719
DATE MANUFACTURED: 10/1999
I/O CARD READY

PROTOCOL INFORMATION

SNMP SET CMTY NAME: NONE
TCP/ IP STATUS: READY
HOST NAME: 131.181.153.109
CONFIG BY: DHCP
IP ADDRESS: 192.168.0.109
SUBNET MASK: 255.255.255.0
DEF. GATEWAY: 192.168.0.1
SYSLOG SERVER: NOT SPECIFIED
IDLE TIMEOUT (SECONDS): 90
BOOTP/DHCP SERVER: 192.168.0.1
CONFIG FILE: NOT SPECIFIED
IPX/SPX STATUS: DISABLED

NETWORK STATISTICS

UNICAST PACKETS RCVD: 4
TOTAL PACKETS RCVD: 10
BAD PACKETS RCVD: 0
FRAMING ERRORS RCVD: 0
PACKETS TRANSMITTED: 40
UNSENDABLE PACKETS: 0
XMIT COLLISIONS: 0
XMIT LATE COLLISIONS: 0

APPLETALK STATUS: READY
ETALK NET: 65281 NODE: 007 P2
APPLETALK NAME: HP Color LaserJ
et 4500
ETALK ZONE: *
DLC/LLC STATUS: READY

Help greatly appreciated.