QUANTUM CORPORATION DLT 7000 (INTERNAL VER. 1) Device Type Internal Tape Drive Interface SCSI-2 Fast/Wide Format DLT Sustained Transfer Rate 5.2 MBPS Size 5.25 in. full height View Top USER CONFIGURABLE SETTINGS Setting Label Position » Factory configured - do not JP1/Pins 1 & Unidentified alter. (Parity enable/disable) 2 » Factory configured - do not JP1/Pins 3 - Unidentified alter. 26 » Factory configured - do not JP2/Pins 1 - Unidentified alter. 2 » Factory configured - do not JP2/Pins 3 - Unidentified alter. (Termination power 4 enable/disable) » Factory configured - do not JP2/Pins 5 - Unidentified alter. 26 » Factory configured - do not JP4 Unidentified alter. (Loader connector) Note: Pin-out of JP4 is unidentified. DRIVE SELECT ID Drive ID JP3/Pins 3 & JP3/Pins 5 & JP3/Pins 7 & JP3/Pins 9 & 4 6 8 10 0 Open Open Open Open 1 Open Open Open Closed 2 Open Open Closed Open 3 Open Open Closed Closed 4 Open Closed Open Open » 5 Open Closed Open Closed 6 Open Closed Closed Open 7 Open Closed Closed Closed 8 Closed Open Open Open 9 Closed Open Open Closed 10 Closed Open Closed Open 11 Closed Open Closed Closed 12 Closed Closed Open Open 13 Closed Closed Open Closed 14 Closed Closed Closed Open 15 Closed Closed Closed Closed Note: Pins 1 & 2 of JP3 are to be closed when selecting SCSI IDs. MANUFACTURERS RECOMMENDED MEDIA Tape Capacity Without Capacity With Compression Compression DLT tape IV 35GB 70GB 1778ft. DLT tape IIIxt 15GB 30GB 1778 DLT tape III 10GB 20GB DIAGNOSTIC LED(S) LED Color Status Condition Write Orange On Cartridge is Protect write-protected. Write Orange Off Cartridge is Protect write-enabled. Tape In Use Yellow Blinking Cartridge is loaded and tape is moving. Tape In Use Yellow Off Cartridge is loaded and ready for use. Use Cleaning Yellow On Drive head requires Tape cleaning, or tape is bad. Use Cleaning Yellow Remains on after Cleaning tap attempted to Tape cleaning tape clean drive head, tape unloaded expired, cleaning not performed. Use Cleaning Yellow Turns on when Problem data cartridge. Tape data cartridge Attempt different loaded after cartridge. cleaning Use Cleaning Yellow Off Cleaning complete, or Tape cleaning unnecessary. Operate Green On Okay to operate cartridge Handle insert/release handle Operate Green Off Do not operate cartridge Handle insert/release handle 2.6 Yellow On Indicates tape is recorded in 2.6GB format. 2.6 Yellow Blinking Indicates tape is recorded in another density selected for a write from BOT. 6.0 Yellow On Indicates tape is recorded in 6.0GB format. 6.0 Yellow Blinking Indicates tape is recorded in another density selected for a write from BOT. 10.0/15.0 Yellow On Indicates tape is recorded in 10.0GB format if DLT™ tape III is used. Indicates tape is recorded in 15.0GB format if DLT™ tape IIIxt is used. 10.0/15.0 Yellow Blinking Indicates tape is recorded in another density selected for a write from BOT. 20.0 Yellow On Indicates tape is recorded in 20.0GB format. 20.0 Yellow Blinking Indicates tape is recorded in another density selected for a write from BOT. DIAGNOSTIC LED(S) LED Color Status Condition 35.0 Yellow On Indicates tape is recorded in 35.0GB format. 35.0 Yellow Blinking Indicates tape is recorded in another density selected for a write from BOT. Compress Yellow On Compression mode enabled (10.0, 15.0, and 35.0GB densities only). Compress Yellow Off Compression mode disabled. Density Yellow On Density from front panel Override selected. Density to be selected by the host (automatic). Density Yellow Off You are in density Override selection mode. Note: All four right side or all seven left side indicators ‘On’ designates that the Power-on self-test (POST) is starting. All four right side or all seven left side indicators ‘Blinking’ designates that an error has occurred in the POST; clear the error by pressing the unload button, or turn drive power off and then on again. If error remains service is required.