BROOKTROUT TECHNOLOGY, INC. TR114+I8V-T1 Card Type ISDN NIC Type ISDN Maximum Onboard Memory 2MB Network Transfer Rate 1.544Mbps Topology Star Wiring Type Unshielded twisted pair Data Bus 16-bit ISA [Image] CONNECTIONS Function Label Function Label RJ-45 UTP connector CN1 MVIP connector CN2 USER CONFIGURABLE SETTINGS Function Label Position Card is first and only card in system SW3/1 On Card is not first in a multiple card system SW3/1 Off T1 loopback test disabled SW5 Off T1 loopback test enabled SW5 On BASE I/O ADDRESS SELECTION Setting SW3/2 SW3/3 SW3/4 SW3/5 SW3/6 SW3/7 SW3/8 100h On On On On On Off On 108h On On On Off On Off On 110h On On On On Off Off On 118h On On On On On On Off 120h On On Off On On On Off 260h On On Off Off On On Off 3D8h Off Off Off Off On On Off 3E0h Off Off Off Off Off On On 3E8h Off Off Off Off Off On Off 3F0h Off Off Off Off Off Off On 3F8h Off Off Off Off Off Off Off Note: A total of 255 base address settings are available. The switches are a binary representation of the decimal memory addresses. SW1/8 is the Most Significant Bit and switch SW1/1 is the Least Significant Bit. The switches have the following decimal values: SW1/8=32768, SW1/7=16384, SW1/6=8192, SW1/5=4096, SW1/4=2048, SW1/3=1024, SW1/2=512, SW1/1=256. Turn off the switches and add the values of the switches to obtain the correct memory address. (Off=1, On=0) INTERRUPT SELECTION IRQ JP1 3 Pins 1 & 2 closed 4 Pins 3 & 4 closed 5 Pins 5 & 6 closed 6 Pins 7 & 8 closed 7 Pins 9 & 10 closed 9 Pins 11 & 12 closed 10 Pins 13 & 14 closed 11 Pins 15 & 16 closed 12 Pins 17 & 18 closed 14 Pins 19 & 20 closed 15 Pins 21 & 22 closed DIAGNOSTIC LED(S) LED Color Status Condition LED1 Red Blinking Data is being transmitted on channel 0 LED1 Red Blinking Channel 0 is off hook (fast) LED2 Red Blinking Data is being transmitted on channel 1 LED2 Red Blinking Channel 1 is off hook (fast) LED3 Red Blinking Data is being transmitted on channel 2 LED3 Red Blinking Channel 2 is off hook (fast) LED4 Red Blinking Data is being transmitted on channel 3 LED4 Red Blinking Channel 3 is off hook (fast) LED5 Red Blinking Data is being transmitted on channel 4 LED5 Red Blinking Channel 4 is off hook (fast) LED6 Red Blinking Data is being transmitted on channel 5 LED6 Red Blinking Channel 5 is off hook (fast) LED7 Red Blinking Data is being transmitted on channel 6 LED7 Red Blinking Channel 6 is off hook (fast) LED8 Red Blinking Data is being transmitted on channel 7 LED8 Red Blinking Channel 7 is off hook (fast) D1 Red On TR114+I8V-T1 in network loopback mode D2 Red On Loss of T1 network signal D3 Yellow On Failing to synchronize on incoming T1 signal D2 & D3 Red/Yellow Both on Board cannot detect a valid T1 signal D4 Green On Operating in normal mode FRM Unidentified On T1 framing error detected BPV Unidentified On T1 bipolar violation detected CRC Unidentified On Discrepancy in cyclic redundancy check detected MVIP CLOCK TERMINATION Setting SW4/1 SW4/2 Terminated On On Not terminated Off Off [Image] USER CONFIGURABLE SETTINGS Function Label Position T1 generates and transmits the clocking SW1/1 Off signals to the TR114 TR114 generates and transmits the clocking SW1/1 On signals to T1 Super frame mode SW1/2 Off Extended super frame mode SW1/2 On B8ZS line coding SW1/3 Off AMI line coding SW1/3 On MVIP clock master set to master SW2/3 Off MVIP clock master set to slave SW2/3 On T1 CABLE LENGTH SETTTINGS Cable Length SW1/4 SW1/5 SW1/6 0 to 132 ft. On On On 133 to 266 ft. Off On On 267 to 398 ft. On Off On 399 to 532 ft. Off Off On 533 to 654 ft. On On Off MVIP STREAM SELECT Mode SW2/1 SW2/2 6/7 Off Off 4/5 On Off 2/3 Off On 0/1 On On SYNC SOURCE CONTROL Setting SW2/3 SW2/4 TR114+I8V-T1 controls Off Off Secondary net card controls Off On FRAMING SIGNAL OUTPUT Setting SW2/3 SW2/4 Disable output On Off Enable output On On TERMINATION Setting SW2/5 SW2/6 Unterminated Off Off Terminated On On