PHILIPS CONSUMER ELECTRONICS, CO. PCA11IM (JUMPER VER.) Card Type Modem Chip Set Unidentified I/O Options Line out, line in, microphone in, speaker out Maximum Modem Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.22, V.22bis, V.23, V.32, V.32bis Fax Modulation Protocol ITU-T V.17, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I & II Data Bus 8-bit ISA [Image] CONNECTIONS Function Label Function Label Line out (RJ-11) CN1 Speaker out CN3 Line in (RJ-11) CN2 Microphone in CN4 SERIAL PORT ADDRESS Setting JP8/A JP8/B COM1 (3F8h) Closed Closed COM2 (2F8h) Open Closed COM3 (3E8h) Closed Open COM4 (2E8h) Open Open INTERRUPT Setting JP8/C JP8/D JP8/E JP8/F IRQ2 Closed Open Open Open IRQ3 Open Closed Open Open IRQ4 Open Open Closed Open IRQ5 Open Open Open Closed SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, E, H, M, O, P, T, V, X, Y, Z &C, &F, &G, &M, &T, &V, &W, &X, &Y, &Z Extended AT Commands %A, %C, %E, %Q \A, \B, \C, \G, \J, \K, \Q, \T, \X S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9,S10, S11, S12, S14, S16, S18, S21, S22, S23, S25 S26, S27, S30, S91 Note: See MHI Help File for full command documentation. PROPRIETARY AT COMMAND SET AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Auto-mode detection disabled; handshake begins at line speed designated by the %B command N1 Auto-mode detection enabled; handshake begins at line speed designated by the %B command and DTE speed COMMUNICATION PROTOCOLS Type: Configuration Format: AT [cmds] Bn [cmds] Description: Selects the communication protocol for data calls Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. Command Protocol B0 ITU-T V.22 at 1200bps B1 Bell 212A at 1200bps B2 ITU-T V.22 at 75/1200Kbps in originate mode, 1200/75Kbps in answer mode DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 DTR ignored &D1 DTR toggle causes online command mode &D2 DTR toggle causes modem to go on-hook &D3 Modem reset on DTR toggle DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DP Pulse dialing enabled DR Answer mode enabled; originate mode disabled following handshake initiation. DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D^ Data calling tone enabled D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 RTS/CTS flow control enabled &K4 XON/XOFF flow control enabled LINE TYPE Type: Configuration Format: AT [cmds] &Ln [cmds] Description: Selects line type Command Line Type &L0 Switched line (PSTN/Dial-up) &L1 Leased line &L2 Power-on leased line PULSE DIALING RATIO Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 39/61ms at 10pps (North America) &P1 33/67ms at 10pps (Europe) &P2 39/61ms at 20pps REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product code I1 Reports ROM checksum I2 Tests and reports ROM checksum I3 Reports model ID & firmware ID I5 Reports country code RESULT CODES Type: Configuration Format: AT [cmds] Qn [cmds] Description: Enables modem to send result codes to the DTE Command Function Q0 Result code sending enabled Q1 Result code sending disabled Q2 "Ring" result code disabled. In answer mode; CONNECT and NO CARRIER disabled SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting EXTENDED AT COMMAND SET CONNECTION SPEED Type: Configuration Format: AT [cmds] %Bn [cmds] Description: Selects maximum modem connection speed Command Function %B300 300bps %B1200 1200bps %B2400 2400bps %B4800 4800bps %B7200 7200bps %B9600 9600bps %B12000 12.0Kbps %B14400 14.4Kbps CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 MNP reliable mode enabled \N3 Auto-reliable mode enabled \N4 V.42 reliable mode enabled \N5 V.42/Normal mode enabled \N6 V.42/MNP mode enabled \N7 MNP/Normal mode enabled EXTENDED RESULT CODES Type: Configuration Format: AT [cmds] \Vn [cmds] Description: Selects extended result codes Command Function \V0 DCE speed displayed. Extended result codes disabled \V1 DCE speed; simple reliable mode extended result codes enabled \V2 DCE speed; detailed reliable mode extended result codes enabled \V3 DTE speed only S(status) -REGISTERS AUTO-RELIABLE FALLBACK CHARACTER Type: Register Format: AT [cmds] S29=n [cmds] Range: 0-127 Unit: ASCII Description: Sets the character used as the auto-reliable fallback character BIT-MAPPED REGISTER S15 Format: AT [cmds] S15=n [cmds] Range: 0-255 Unit: Bit-mapped Description: Controls MNP options, break types, DTE rate adjustments. Note: Further information is currently unavailable BIT-MAPPED REGISTER S17 Format: AT [cmds] S17=n [cmds] Range: 0-255 Unit: Bit-mapped Description: Controls relaible mode, data compression, and extended responses Note: Further information is currently unavailable BIT-MAPPED REGISTER S19 Format: AT [cmds] S19=n [cmds] Range: 0-255 Unit: Bit-mapped Description: Determines flow control, echo, XON/XOFF pass-through Note: Further information is currently unavailable BIT-MAPPED REGISTER S20 Format: AT [cmds] S20=n [cmds] Range: 0-255 Unit: Bit-mapped Description: Sets PC/NEC baud rate options, guard tones Note: Further information is currently unavailable BIT-MAPPED REGISTER S24 Format: AT [cmds] S24=n [cmds] Range: 0-255 Unit: Bit-mapped Description: Controls make/break ratio, auto retrain, V.34/VFC, auto mode Note: Further information is currently unavailable BIT-MAPPED REGISTER S28 Format: AT [cmds] S28=n [cmds] Range: Unidentified Unit: Bit-mapped Description: Determine DCE rate Note: Further information is currently unavailable SLEEP TIMER Type: Register Format AT [cmds] S13=n [cmds] Range: 0-255 Unit: 1 second Description: Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode.