ACTION WELL DEVELOPMENT, LTD. AC-5618 (REV. 1.0) Card Type Modem Chipset Unidentified I/O Options Audio in - CD-ROM, speaker connector, line in, line out, audio in, audio out, microphone in Maximum Modem Rate 56.0Kbps Maximum Fax Rate 14.4Kbps Fax Class Class I Modem Modulation Protocol Bell 103/212A ITU-T V.22bis,V.32, V.32bis, V.34, V.34bis, V.90 Fax Modulation Protocol ITU-T V.17 Error Correction/Compression MNP5, V.42, V.42bis Data Bus 16-bit ISA [Image] CONNECTIONS Function Label Function Label Line in CN1 Audio out CN5 Line out CN2 Audio in - CD-ROM CN6 Microphone in CN3 Audio in - CD-ROM CN7 Audio in CN4 SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, E, H, M, O, P, Q, T, V &C, &P, &V, &W, &Z Extended AT Commands \A, \B, \N %C, %E S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12 Special Commands +MS, #CID Voice Commands #TL, #VBT, #VRA, #VRX, #VSD, #VSP, #VSS, #VTD, #VTS, #VTX, #SPK Note: See MHI Help File for full command documentation. Further information on S-registers is currently unavailable Proprietary AT Command Set AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Auto-mode detection disabled. Handshake begins at line speed designated by the S32 register N1 Auto-mode detection enabled. Handshake conducted according to the automode algorithm supported by the modem COMMUNICATION PROTOCOLS Type: Configuration Format: AT [cmds] Bn [cmds] Description: Selects the communication protocol for data calls Command Protocol B0 ITU-T V.22 at 1200bps COMPRESSION Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Selects data compression Command Function &K0 Data compression disabled &K1 MNP5 enabled &K2 V.42bis enabled &K3 MNP5 and V.42bis; or data compression and correction enabled CONNECT MESSAGE SPEED SOURCE Type: Configuration Format: AT [cmds] &En [cmds] Description: Selects source for speed field in CONNECT message Command Function &E0 DCE speed field &E1 DTE speed field CONNECT MESSAGES Type: Configuration Format: AT [cmds] &An [cmds] Description: Selects the format of CONNECT messages Command Function &A0 CONNECT only &A1 Modulation indicator added to CONNECT message &A2 Error detection and data compression indicators added to CONNECT message &A3 Modulation, error detection and data compression indicators added to CONNECT message DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 DTR forced high &D1 DTR toggle causes online command mode &D2 Normal DTR operations &D3 Resets on receipt of DTR DEFAULT CONFIGURATION Type: Configuration Format: AT [cmds] Yn [cmds] Description: Selects the default user defined configuration Note: Does not load configuration Command Function Y0 Select user template 0 Y1 Select user template 1 Y2 Select factory setting 0 Y3 Select factory setting 1 DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &Fn [cmds] Description: Sets values in active profile to values found in the default profile Command Function &F0 Restore factory configuration 0 &F1 Restore factory configuration 1 FLOW CONTROL Type: Configuration Format: AT [cmds] &Hn [cmds] Description: Enables/disables flow control Command Function &H0 Flow control disabled &H1 RTS to CTS flow control enabled REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I1 Reports manufacturer and model name I2 Reports software version and provider I3 Reports vendor/chip ID I4 Reports stored and active profile I5 Reports stored and active profile I6 Reports stored and active profile I7 Reports stored telephone numbers RTS/CTS Type: Configuration Format: AT [cmds] &Rn [cmds] Description: Selects RTS/CTS options Command Function &R0 RTS is ignored &R1 Modem recieves data only on RTS SELECT CALL PROGRESS RESULT CODES Type: Configuration Format: AT [cmds] Xn [cmds] Description: Enables selection of tone detection and associated result code format options Command Function X0 Busy and dial tone detection disabled; result codes 0 - 4 enabled. X1 Busy and dial tone detection disabled; result codes 0 - 5 & 9 - 1212 enabled. X2 Busy tone detection disabled, dial tone detection enabled; result codes 0 - 6 & 9 - 1212 enabled. X3 Busy tone detection enabled, dial tone detection disabled; result codes 0 - 5, 7 - 1212 enabled. X4 Busy and dial tone detection enabled; result codes 0 - 1212 enabled. SOFT RESET Type: Immediate Format: AT [cmds] Zn [cmds] Description: Restores modem profiles previously saved in non-volatile RAM Command Function Z0 Restore default user template as defined by Yn Z1 Restore user template 0 Z2 Restore user template 1 Z3 Restore factory setting 0 Z4 Restore factory setting 1 SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting TEST MODES Type: Immediate Format: AT [cmds] &Tn Description: Selects test options Command Function &T0 TBD &T1 TBD &T2 TBD &T3 TBD EXTENDED AT COMMAND SET BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal Command Function \K0 Online command mode enabled, send no break to remote modem \K1 Break sent to remote modem and buffered cleared \K2 Online command mode enabled, send no break to remote modem \K3 Send break to remote modem immediately \K4 Online command mode enabled, send no break to remote modem \K5 Send break with transmitted data VOICE COMMANDS INACTIVITY TIMER Type: Configuration Format: AT [cmds] #VIT=n [cmds] Range: 0-255 Unit: .1ms Description: Maximum duration of voice inactivity allowed prior to initiating hang-up process. MODE SELECTION Type: Immediate Format: AT [cmds] #CLS=n [cmds] Description: Selects which mode the modem will operate in. Command Function #CLS=0 Modem will operate in data mode. #CLS=1 Modem will operate in fax class I mode. #CLS=8 Modem will operate in voice mode. RECORD GAIN Type: Configuration Format: AT [cmds] #RG=hhhh [cmds] Range: 0000 - 7FFF Unit: Unidentified (hexadecimal) Description: Sets the record gain. #RG? queries value VOICE - LOCAL SERIAL PORT SPEED Type: Configuration Format: AT [cmds] #BDR=n [cmds] Range: 0-48 Unit: 2400bps Description: Sets the speed of the local serial port when in voice mode. VOICE DEVICE Type: Configuration Format: AT [cmds] #VLS=n [cmds] Description: Selects the I/O device for the DSP chip. Note: VLS? Queries current setting. #VLS=? Command will display the available options. Command Function #VLS=0 Telephone line and handset used for voice I/O. #VLS=2 Internal speaker only used for voice I/O. #VLS=3 External microphone only used for voice I/O. #VLS=4 Telephone line and handset used for voice I/O; internal speaker enabled. #VLS=6 Speakerphone used for voice I/O. VOICE PARAMETERS Type: Configuration Format: AT [cmds] #VIP [cmds] Description: Initializes voice parameters VOICE RING DETECT TIME Type: Configuration Format: AT [cmds] #VRN=n [cmds] Default: Unidentified Range: 0-255 Unit: .1ms Description: Sets the maximum time the modem will wait for the remote station to ring before it assumes that it went off-hook before it rang. VOICE SAMPLE QUALITY Type: Configuration Format: AT [cmds] #VBS=n [cmds] Description: Selects the number of bits per sample that the modem records. Note: This modem may not support all options listed below. The #VBS? Command will display the available options. Command Function #VBS=2 Modem records 2 bits per sample in ADPCM encoding. #VBS=4 Modem records 4 bits per sample in ADPCM encoding. #VBS=8 Modem records 8 bits per sample in PCM encoding. #VBS=16 Modem records 16 bits per sample in PCM encoding. VOICE SAMPLING RATE Type: Configuration Format: AT [cmds] #VSR=n [cmds] Description: Sets the sampling rate used when recording voice signals. #VSR? queries settings Command Function #VSR=7200 Selects a sampling rate of 7.2KHz. #VSR=8000 Selects a sampling rate of 8.0KHz. VOICE TIMING MARK Type: Configuration Format: AT [cmds] #VTM=n [cmds] Range: 1-10 Unit: 1ms Description: Configures timing mark placement. VOICE VOLUME LEVEL Type: Configuration Format: AT [cmds] #VGT=n [cmds] Range: 0-255 Description: Sets the volume level when playing back audio signals.