ARCHTEK CORPORATION 5634PEW Card Type Modem/Fax card Chip Set ESS Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34, V.90 Fax Modulation Protocol ITU-T V.17, V.27ter, V.29, V.21CH2 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I Data Bus PCI [Image] CONNECTIONS Function Label Function Label Line in (RJ-11) CN1 Line out (RJ-11) CN2 SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, ‘comma’, A/ A, B, E, H, P, Q, T, V, W, X, Y, Z &C, &P, &V, &W, &Y, &Z Extended AT Commands \A, \G, \L %C S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S21, S22, S29, S32, S33 Note: See MHI Help File for full command documentation. PROPRIETARY AT COMMAND SET AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Auto-mode detection disabled N1 Auto-mode detection enabled AUXILIARY RELAY CONTROL Type: Configuration Format: AT [cmds] &Jn [cmds] Description: Enables/disables A/A1 relay driver. Not for use with RJ-11 phone lines Command Jack Type &J0 Auxiliary relay is disabled COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Asynchronous mode COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Qn [cmds] Description: Selects communications mode options Command Mode &Q0 Asynchronous mode, serial port speed follows connect speed. DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 DTR override &D1 DTR toggle causes online command mode &D2 DTR toggle causes modem to go on-hook DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &Fn [cmds] Description: Sets values in active profile to values found in the default profile Command Function &F0 Restore stored profile 0 after warm reset &F1 Restore stored profile 1 after warm reset FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 RTS/CTS flow control enabled &K4 XON/XOFF flow control enabled &K5 Transparent XON/XOFF flow control enabled &K6 RTS/CTS & XON/XOFF flow control enabled LINE TYPE Type: Configuration Format: AT [cmds] &Ln [cmds] Description: Command nonfunctional Command Line Type &L0 Returns OK ON-LINE Type: Immediate Format: AT [cmds] On [cmds] Description: Controls on-line command (data transmission) state options. Note: The O command must be placed at the end of the command string. Command Function O0 On-line command mode with no retraining enabled O1 On-line command mode with long retrain sequence enabled O2 On-line command mode with short retrain sequence enabled REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product code I1 Reports hardware variation code I2 Reports DSP firmware revision I3 Reports modem firmware revision information I4 Reports response programmed by modem manufacturer SPEAKER MODE Type: Configuration Format: AT [cmds] Mn [cmds] Description: Selects various speaker options Command Function M0 Speaker disabled M1 Speaker enabled until carrier signal detected M2 Speaker enabled TEST MODES Type: Immediate Format: AT [cmds] &Tn Description: Selects test options Command Function &T0 End current test &T1 Begin local analog loopback test TRANSMIT CARRIER Type: Configuration Format: AT [cmds] Cn [cmds] Description: Controls the transmit carrier switching. Command nonfunctional Command Function C1 Returns OK message EXTENDED AT COMMANDS CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Normal mode enabled \N2 Reliable mode enabled \N3 Auto-reliable mode enabled \N4 V.42 reliable mode enabled \N5 MNP reliable mode enabled