ARCHTEK CORPORATION 5634PCA-K Card Type Modem/Fax card Chip Set Cirrus Logic Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34, K56flex Fax Modulation Protocol ITU-T V.17, V.27ter, V.29, T.4, T.30 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I Data Bus PCMCIA 55075 SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, E, H, L, M, P, Q, T, V, W, X, Y &B, &C, &D, &G, &V, &Z Extended AT Commands \J, \T %A, %G Special Commands +MS, -C S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S24, S30 Note: See MHI Help File for full command documentation. PROPRIETARY AT COMMAND SET AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 In originate or answer mode, handshake occurs only in mode designated by the ATB command and S37 register. N1 In originate or answer mode, handshake begins at line speed designated by the S37 register and ATB command. Modem may shift to a lower speed AUXILIARY RELAY CONTROL Type: Configuration Format: AT [cmds] &Jn [cmds] Description: Enables/disables A/A1 relay driver. Not for use with RJ-11 phone lines Command Jack Type &J0 Auxiliary relay is never closed COMMUNICATION PROTOCOLS Type: Configuration Format: AT [cmds] Bn [cmds] Description: Selects the communication protocol for data calls Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. Command Protocol B0 ITU-T V.22 at 1200bps or V.21 at 300bps B1 Bell 212A at 1200bps/ Bell 103J at 300bps B2 ITU-T V.23 at 75/1200bps originate; 1200/75bps answer B3 ITU-T V.23 at 1200/75bps answer; 75/1200bps originate B15 ITU-T V.22 at 1200bps or V.21 at 300bps B16 Bell 212A at 1200bps/ Bell 103J at 300bps COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Asynchronous mode COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Qn [cmds] Description: Selects communications mode Command Mode &Q0 Buffered asynchronous mode &Q5 Error correction mode &Q6 Buffered asynchronous mode DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 DTR override &D1 DTR toggle causes online command mode &D2 Normal DTR operations &D3 Resets on receipt of DTR DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. D^ Data calling tone disabled D$ Wait for credit card "bong" tone before processing the remaining characters in the dial string ECHOPLEX VALIDITY Type: Configuration Format: AT [cmds] Fn [cmds] Description: Selects whether commands sent while in data mode are echoed Command Function F1 Echoplex disabled FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &F [cmds] Description: Sets values in active profile to values found in the default profile Command Function &F0 Sets values in active profile to factory settings &F5 Sets values in active profile to factory settings for ETC mode FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 RTS/CTS hardware flow control enabled &K4 XON/XOFF software flow control enabled ON-LINE Type: Immediate Format: AT [cmds] On [cmds] Description: Controls on-line command (data transmission) state options. Note: The O command must be placed at the end of the command string. Command Function O0 On-line command mode disabled; return to data mode O1 On-line command mode with retraining enabled O2 Rate negotiation issued before returning to online command mode PULSE DIALING RATIO Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 39/61ms at 10pps (North America) &P1 33/67ms at 10pps (Europe) &P2 33/67ms at 20pps REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports modem firmware revision information I1 Reports ROM checksum I2 Tests and reports ROM checksum I3 Reports modem firmware revision information I12 Reports country code RESTORE PROFILE ON POWER-UP Type: Configuration Format: AT [cmds] &Yn [cmds] Description: Restores a selected profile into the active profile on power-up (hard reset) Command Function &Y0 Restore profile 0 on power-up SOFT RESET Type: Immediate Format: AT [cmds] Zn [cmds] Description: Restores modem profiles previously saved in non-volatile RAM using the &W command. Command Function Z0 Restore setting 0 STORE ACTIVE PROFILE Type: Configuration Format: AT [cmds] &Wn [cmds] Description: Writes the values for the active profile into the non-volatile RAM Command Function &W0 Write the active profile to stored profile 0 TEST MODES Type: Immediate Format: AT [cmds] &Tn Description: Selects test options Command Function &T0 End current test &T1 Begin local analog loopback test &T3 Begin local digital loopback request &T6 Request remote digital loopback TRANSMIT CARRIER Type: Configuration Format: AT [cmds] Cn [cmds] Description: Controls the transmit carrier switching Command Function C1 Transmit carrier enabled EXTENDED AT COMMANDS BLACKLIST Type: Configuration Format: AT [cmds] %Bn [cmds] Description: Displays numbers which failed the last call attempt within two hours. In countries that do not require blacklisting, command returns ERROR BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal Command Function \K5 Modem sends break to remote modem in sequence with transmitted data; non-destructive/non-expedited CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Normal mode enabled \N2 Reliable mode enabled \N3 Auto-reliable mode enabled \N4 V.42 reliable mode enabled \N5 MNP reliable mode enabled FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] \Qn [cmds] Description: Sets type of flow control used by modem Command Function \Q0 Flow control disabled \Q1 Bi-directional XON/XOFF flow control enabled \Q2 RTS/CTS flow control to DTE enabled FLOW CONTROL Type: Configuration Format: AT [cmds] \Gn [cmds] Description: Selects modem port flow control. For compatibility only. Command Function \G0 Returns OK XON/XOFF PASS-THROUGH Type: Configuration Format: AT [cmds] \Xn [cmds] Description: Selects whether XON/XOFF signals are sent to remote modem Command Function \X0 XON/XOFF signals trapped by local modem SPECIAL COMMANDS IDENTIFY MODEM MANUFACTURER Type: Configuration Format: AT [cmds] +GMI? [cmds] Description: Commands DCE to send a message to the DTE indicating the DCE manufacturer Note: Modem manufacturers name may be changed using the firmware configuration utility IDENTIFY PRODUCT MODEL Type: Configuration Format: AT [cmds] +GMM? [cmds] Description: Commands DCE to send a message to the DTE indicating the modem chipset name Note: Modem product model may be changed using the firmware configuration utility IDENTIFY PRODUCT REVISION Type: Configuration Format: AT [cmds] +GMR? [cmds] Description: Commands DCE to send a message to the DTE indicating the modem chipset revision level Note: Modem chipset revision level may be changed using the firmware configuration utility S(status) -REGISTERS AUTO MODE Format: AT [cmds] S43=n [cmds] Range: 0-1 Unit: Unidentified Description: Enables/disables V.32bis start-up mode. Note: For testing and debugging purposes only Command Function S43=0 V.32bis srtart-up mode disabled S43=1 V.32bis srtart-up mode enabled AUTO RATE Format: AT [cmds] S42=n [cmds] Range: 0-1 Unit: Unidentified Description: Enables/disables V.32 and V.22bis auto rate. Note: For testing and debugging purposes only Command Function S42=0 V.32 and V.22bis auto rate disabled S42=1 V.32 and V.22bis auto rate enabled BIT-MAPPED REGISTER S14 Format: AT [cmds] S14=n [cmds] Range: 0-174 Unit: Bit-mapped Description: Controls result codes display, and dial mode Bit Value Function 2 - 0 0 Reserved 3 0 Display result codes in numeric format 1 Display result codes in verbose format 6 0 1 Pulse dial set to 10pps Pulse dial set to 20pps 7 0 Reserved BIT-MAPPED REGISTER S21 Format AT [cmds] S21=n [cmds] Range: 0-253 Unit: Bit-mapped Description: Selects jack type, CTS/DCD/DSR signals, low DTR action, and the long space disconnect function. Bit Value Function 2 - 0 0 Reserved 4, 3 00 DTR signal ignored 01 Modem goes to command mode on low DTR 10 Modem disconnects on low DTR; Auto-Answer is disabled. 11 Modem is initialized on low DTR 5 0 DCD forced high 1 DCD normal 6, 7 0 Reserved BIT-MAPPED REGISTER S22 Format AT [cmds] S22=n [cmds] Range: 0-255 Unit: Bit-mapped Description: Controls speaker volume and controls, limits results codes, and pulse dial make/break ratio. Bit Value Function 3 - 0 0 Reserved 6 - 4 000 Basic result codes only enabled 100 Basic and connection speed result codes enabled 101 Basic and connection speed result codes and dialtone detection enabled 110 All result codes except dialtone detection 111 enabled All result codes enabled 7 0 39/61ms at 10pps (North America) 1 33/67ms at 10pps (Europe) DATA CALLING TONE Format: AT [cmds] S35=n [cmds] Range: 0-1 Unit: Unidentified Description: Enables/disables data calling tone. S35=0 disables DCE LINE SPEED Type: Register Format AT [cmds] S37=n [cmds] Description: Sets the maximum allowable data exchange rate attempted during handshake process. Command Function S37=0 Maximum line speed S37=2 1200/75bps S37=3 300bps S37=5 1200bps S37=6 2400bps S37=7 4800bps S37=8 7200bps S37=9 9600bps S37=10 12.0Kbps S37=11 14.4Kbps S37=12 16.8Kbps S37=13 19.2Kbps S37=14 21.6Kbps S37=15 24.0Kbps S37=16 26.4Kbps S37=17 28.8Kbps S37=18 31.2Kbps S37=19 33.6Kbps 56K DCE LINE SPEED Type: Register Format AT [cmds] S38=n [cmds] Description: Sets the maximum allowable 56K downstream rate attempted during handshake process. Command Function S38=0 56K disabled S38=1 56K automatic speed select S38=2 32.0Kbps S38=3 34.0Kbps S38=4 36.0Kbps S38=5 38.0Kbps S38=6 40.0Kbps S38=7 42.0Kbps S38=8 44.0Kbps S38=9 46.0Kbps S38=10 48.0Kbps S38=11 50.0Kbps S38=12 52.0Kbps S38=13 54.0Kbps S38=14 56.0Kbps S38=15 58.0Kbps S38=16 60.0Kbps ERROR CORRECTION NEGOTIATION Type: Register Format AT [cmds] S36=n [cmds] Description: Selects the action of the modem if it fails to connect with the error-correction protocol set in &Q. Command Function S36=0 Hang up S36=1 Fall-back to asynchronous connection S36=2 Hang up S36=3 Fall-back to asynchronous connection S36=4 Attempt a connection at MNP2-4; if that fails, hang up. S36=5 Attempt a connection at MNP2-4; if that fails, fall-back to asynchronous connection S36=6 Attempt a connection at MNP2-4; if that fails, hang up. S36=7 Attempt a connection at MNP2-4; if that fails, fall-back to asynchronous connection ETC STARTUP AUTORATING Type: Register Format AT [cmds] S40=n [cmds] Description: Determines default auto-rating Command Function S40=0 Start up with normal auto-rating S40=1 Start up at initial rate of 4800bps or below S40=2 Start up at initial rate of 9600bps or below FEATURE NEGOTIATION OPTIONS Type: Register Format: AT [cmds] S48=n [cmds] Description: Selects active error correction and compression protocols Command Function S48=7 Detection negotiation and XID negotiation enabled S48=128 Fall-back to options set in S36 LOCAL PHONE STATUS Type: Register Format: AT [cmds] S90=n [cmds] Description: Displays the status of the local phone Command Function S90=0 Local phone on-hook S90=1 Local phone off-hook SLEEP TIMER Type: Register Format AT [cmds] S89=n [cmds] Range: 0, 5-255 Unit: Unidentified Description: Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. SYNTHETIC RING FREQUENCY Format: AT [cmds] S33=n [cmds] Range: 1-5 Unit: Unidentified Description: Determines synthetic ring frequency. S33=0 disables SYNTHETIC RING VOLUME Format: AT [cmds] S32=n [cmds] Range: Unidentified Unit: -1dB Description: Determines synthetic ring volume TRANSMISSION LEVEL - DIRECT CONNECT Type: Register Format: AT [cmds] S92=n [cmds] Default: 20 Range: Unidentified Unit: -1 dBm Description: Sets the signal level for transmission for direct connections TRANSMISSION LEVEL - LINE Type Register or Configuration Format AT [cmds] S91=n [cmds] Range 6-15 Unit -1 dBm Description Sets the signal level for transmission over phone lines Note: Register only functions for Japan V.34 MODULATION Type: Register Format AT [cmds] S28=n [cmds] Range: 0-255 Unit: Unidentified Description: Enables V.34 modulation protocol. S28=0 disables