ACTIONTEC ELECTRONICS, INC. DESKVOICE V.90 Card Type Modem, Fax Chip Set Unidentified I/O Options line in, line out Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.90, K56flex, V.21, V.22, V.23 Fax Modulation Protocol Unidentified Error Correction/Compression MNP5, V.42, V.42bis Fax Class Unidentified Data Bus 16-bit ISA Card Size Half-length, half-height card [Image] CONNECTIONS Function Label Function Label Line out (RJ-11) CN1 Line in (RJ-11) CN2 SERIAL PORT ADDRESS Setting JP1 COM1 (3F8h) Pins 1 & 2 closed COM2 (2F8h) Pins 1 & 2, 3 & 4 closed COM3 (3E8h) Pins 1 & 2, 5 & 6 closed COM4 (2E8h) Pins 1 & 2, 3 & 4, 5 & 6 closed Plug and Play Open INTERRUPT Setting JP2 3 Pins 1 & 2 closed 4 Pins 3 & 4 closed 5 Pins 5 & 6 closed 7 Pins 7 & 8 closed 9 Pins 9 & 10 closed 10 Pins 11 & 12 closed 11 Pins 13 & 14 closed 12 Pins 15 & 16 closed 15 Pins 17 & 18 closed SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, C, E, H, M, P, Q, T, W, Z &C, &G, &V, &Z Extended AT Commands \A, \B, \J, \K, \T, \X S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S24, S30, S91, S92 Note: See MHI Help File for full command documentation. Proprietary AT Command Set AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Auto-mode detection disabled N1 In originate mode, handshake begins at line speed designated by the S37 register. Modem can shift to a slower speed if necessary. In answer mode, handshake attempted with the following protocols in order - V.FC, V.32bis, V.32, V.22bis, V.22 or Bell 212, V.21, and Bell 103 AUXILIARY RELAY Type: Configuration Format: AT [cmds] &Jn [cmds] Description: Controls the auxiliary relay function. Command Function &J0 Auxiliary relay never closed COMMUNICATION PROTOCOLS Type: Configuration Format: AT [cmds] Bn [cmds] Description: Selects the communication protocol for data calls Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. Command Protocol B0 ITU-T V.22 at 1200bps B1 Bell 212A at 1200bps B2 Unselect V.23 reverse channel B3 Unselect V.23 reverse channel B15 V.21 at 300bps B16 Bell 103J at 300bps COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Asynchronous mode COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Qn [cmds] Description: Selects communications mode options Command Mode &Q0 Asynchronous mode, serial port speed follows connect speed. &Q1 Reserved &Q2 Reserved &Q3 Reserved &Q4 Reserved &Q5 Buffered error correction mode &Q6 Buffered asynchronous mode &Q7 Reserved &Q8 MNP error control mode &Q9 V.42 or MNP error control mode DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 Modem does not respond to DTR &D1 Modem goes to command mode after DTR goes is off &D2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. &D3 Modem is initialized after DTR goes off DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D^ Disable data calling tone transmission D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D$ Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. ECHOPLEX VALIDITY Type: Configuration Format: AT [cmds] Fn [cmds] Description: Selects whether commands sent while in data mode are echoed Command Function F1 Echoplex disabled FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &F [cmds] Description: Sets values in active profile to values found in the default profile Command Function &F0 Recall factory setting as active configuration FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 RTS/CTS flow control enabled &K4 XON/XOFF flow control enabled LONG SPACE DISCONNECT Type: Configuration Format: AT [cmds] Yn [cmds] Description: Commands the modem to disconnect after a 1.6 second break is detected Command Function Y0 Long space disconnect function disabled ON-LINE Type: Immediate Format: AT [cmds] On [cmds] Description: Controls on-line command (data transmission) state options. Note: The O command must be placed at the end of the command string. Command Function O0 On-line command mode with no retraining enabled O1 On-line command mode with retraining enabled O3 Issue rate renegotiation before returning to online data mode PULSE DIALING RATIO Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 39/61ms at 10pps (North America) &P1 33/67ms at 10pps (Europe) &P2 39/61ms at 20pps REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports modem firmware revision number and speed I1 Reports ROM checksum I2 Tests and reports ROM checksum I3 Reports the default speed and the controller firmware version I4 Reports data pump firmware version I5 Reports the board ID: software version, hardware version, and country ID I6 Reports OK I7 Reports OK I8 Reports OK I9 Reports country code I11 Displays diagnostic information about the last connection RESTORE PROFILE ON POWER-UP Type: Configuration Format: AT [cmds] &Yn [cmds] Description: Restores a selected profile into the active profile on power-up (hard reset) RESULT CODE FORMAT Type: Configuration Format: AT [cmds] Vn [cmds] Description: Selects word or numeric format for information-text and result codes Command Function V1 Verbose (word) format enabled SELECT CALL PROGRESS RESULT CODES Type: Configuration Format: AT [cmds] Xn [cmds] Description: Enables selection of tone detection and associated result code format options Command Function X0 Busy and dial tone detection disabled; result codes 0 - 4 enabled. X1 Busy and dial tone detection disabled; result codes 0 - 5 & 10 enabled. X2 Busy tone detection disabled, dial tone detection enabled; result codes 0 - 6 & 10 enabled. X3 Busy tone detection enabled, dial tone detection disabled; result codes 0 - 5, 7 & 10 enabled. X4 Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled. X5 Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled. X6 Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled. X7 Busy and dial tone detection enabled; result codes 0 - 7 & 10 disabled. SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Lowest volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting STORE ACTIVE PROFILE Type: Configuration Format: AT [cmds] &Wn [cmds] Description: Writes the values for the active profile into the non-volatile RAM TEST MODES Type: Immediate Format: AT [cmds] &Tn Description: Selects test options Command Function &T0 End current test &T1 Begin local analog loopback test &T3 Begin local digital loopback &T6 Request remote digital loopback V.32 - AUTO-RETRAIN Type: Configuration Format: AT [cmds] &Bn [cmds] Description: Controls auto-retrain function if poor line quality is detected Command Function &B1 Auto-retrain enabled if line quality is poor Extended Result Codes BLACKLIST Type: Configuration Format: AT [cmds] %B [cmds] Description: View numbers in blacklist COMPRESSION Type: Configuration Format: AT [cmds] %Cn [cmds] Description: Selects data compression Command Function %C0 Data compression disabled %C1 V.42bis and MNP5 enabled CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 Reliable mode enabled \N3 Auto-reliable mode enabled \N4 V.42 reliable mode enabled \N5 Auto-reliable mode enabled \N7 Auto-reliable mode enabled EXTENDED RESULT CODES Type: Configuration Format: AT [cmds] \Vn [cmds] Description: Selects extended result codes Command Function \V0 Extended result codes disabled \V1 Extended result codes enabled \V2 Extended result codes enabled FLOW CONTROL Type: Configuration Format: AT [cmds] \Gn [cmds] Description: Selects modem port flow control Note: Command performs no function; included for compatibility only. FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] \Qn [cmds] Description: Sets type of flow control used by modem Command Function \Q0 Flow control disabled \Q1 Bidirectional XON/XOFF flow control enabled \Q3 Bidirectional RTS/CTS flow control enabled RING INDICATOR Type: Configuration Format: AT [cmds] \Rn [cmds] Description: Controls the ring indicator signal Command Function \R0 Ring indicator signal is off after the telephone call is answered Special Commands DATA CALLING TONE Type: Configuration Format: AT [cmds] -Cn [cmds] Description: Controls the data calling tone Command Function -C0 Disable data calling tone -C1 Enable data calling tone LINE-TO-LINE LOOPBACK Type: Configuration Format: AT [cmds] &&Ln [cmds] Description: Provides a loopback for line-to-line WRITE TO/READ FROM REGISTER Type: Configuration Format: AT [cmds] &&Cn [cmds] Description: Controls the write to/read from character WRITE TO/READ FROMD DSP RAM LOCATION Type: Configuration Format: AT [cmds] &&Rn [cmds] Description: Sets the write to/read from DSP RAM location S(status) -REGISTERS 56K DIAL LINE RATE Type: Register Format AT [cmds] S38=n [cmds] Description: Sets the maximum allowable data exchange rate attempted during handshake process. Command Function S38=0 V.90 disabled S38=1 Autorate S38=2 29333bps S38=3 30666bps S38=4 32000bps S38=5 33333bps S38=6 34666bps S38=7 36000bps S38=8 37333bps S38=9 38666bps S38=10 40000bps S38=11 41333bps S38=12 42666bps S38=13 44000bps S38=14 45333bps S38=15 46666bps S38=16 48000bps S38=17 49333bps S38=18 50666bps S38=19 52000bps S38=20 53333bps AUTO RATE Type: Register Format AT [cmds] S42n [cmds] Description: Controls the auto rate Command Function S42=0 Disabled S42=1 Enabled AUTOMODE Format AT [cmds] S43=n [cmds] Default: 1 Range: 0-1 Description: This command used for testing and debugging only Command Function S43=0 Automode disabled S43=1 Automode enabled BIT-MAPPED REGISTER S14 Format: AT [cmds] S14=n [cmds] Default: 8 Range: 0-174 Unit: Bit-mapped Description: Controls echo, result codes and display, dial mode, and answer/originate mode. Bit Value Function 3 0 Display result codes in numeric format 1 Display result codes in verbose format 6 0 10 PPS 1 20 PPS BIT-MAPPED REGISTER S21 Format AT [cmds] S21=n [cmds] Default: 48 Range: Unidnetified Unit: Bit-mapped Description: Indicates the status of command options Bit Value Function 4, 3 0 Modem does not respond to DTR 1 Modem goes to command mode after DTR goes is off 2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is 3 disabled. Modem is initialized after DTR goes off 5 0 Data compression disabled 1 V.42bis and MNP5 enabled BIT-MAPPED REGISTER S22 Format AT [cmds] S22=n [cmds] Default: Unidentified Range: 0-255 Unit: Bit-mapped Description: Indicates the status of command options Bit Value Function 6 - 4 0 Busy and dial tone detection disabled; result codes 0 - 4 enabled. 4 Busy and dial tone detection disabled; result 5 codes 0 - 5 & 10 enabled. 6 Busy tone detection disabled, dial tone detection enabled; result codes 0 - 6 & 10 7 enabled Busy tone detection enabled, dial tone detection disabled; result codes 0 - 5, 7 & 10 enabled. Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled. 7 0 39/61ms at 10pps (North America) 1 33/67ms at 10pps (Europe) BIT-MAPPED REGISTER S28 Format AT [cmds] S28=n [cmds] Default: unidentified Range: 0-31 Unit: Bit-mapped Description: Controls V.23 split speed, transmit/receive speed, half duplex; and pulse dialing. Value Function 0 Disable 1-255 Enable BIT-MAPPED REGISTER S40 Format AT [cmds] S40=n [cmds] Default: 0 Range: 0-2 Unit: Bit-mapped Description: Controls ETC startup autorating Command Function S40=0 Startup with normal autorating S40=1 Startup with initial rate of 4800 or below S40=2 Startup with initial rate of 9600 or below DATA CALLING TONE Type: Register Format AT [cmds] S35n [cmds] Description: Controls the data calling tone Command Function S35=0 Disabled S35=1 Enabled DCE LINE SPEED Type: Register Format AT [cmds] S37=n [cmds] Description: Sets the maximum allowable data exchange rate attempted during handshake process. Command Function S37=0 Maximum modem S37=1 Reserved S37=2 1200/75bps S37=3 300bps S37=4 Reserved S37=5 1200bps S37=6 2400bps S37=7 4800bps S37=8 7200bps S37=9 9600bps S37=10 12000bps S37=11 14400bps S37=12 16800bps S37=13 19200bps S37=14 21600bps S37=15 24000bps S37=16 26400bps S37=17 28800bps S37=18 31200bps S37=19 33600bps FEATURE NEGOTIATION OPTIONS Type: Register Format: AT [cmds] S48=n [cmds] Description: Selects active error correction and compression protocols Command Function S48=7 Detection negotiation and XID negotiation enabled S48=128 Fall-back to options set in S36 K56FLEX AND V.90 SELECTION Type: Register Format: AT [cmds] S109=n [cmds] Description: Controls the K56flex/V.90 protocols Command Function S109=0 Disable all 56K connection S109=1 K56flex first, then V.90 S109=2 V.90 only. K56flex disabled LOCAL PHONE STATUS Type: Register Format: AT [cmds] S90=n [cmds] Description: Sets the status of the local phone Command Function S90=0 Local phone on-hook S90=1 Local phone off-hook NEGOTIATION FALLBACK Type: Register Format AT [cmds] S36=n [cmds] Description: Controls the negotiation fallback Command Function S36=0, 2 Hang up S36=1, 3 Attempt a direct connection S36=4, 6 Attempt a connection at MNP2-4; if that fails, hang up. S36=5, 7 Attempt a connection at MNP2-4; if that fails, attempt a direct connection. SLEEP MODE Type: Register Format AT [cmds] S89n [cmds] Default: 10 Range: 0, 5-255 Description: Controls the sleep mode timer SYNTHETIC RING FREQUENCY Type: Register Format: AT [cmds] S33=n [cmds] Default: 0 Range: 0-5 Unit: Unidentified Description: Specifies a synthetic ring frequency SYNTHETIC RING VOLUME Type: Register Format: AT [cmds] S32=n [cmds] Default: 16 Range: Unidentified Unit: dB Description: Specifies a synthetic ring volume with implied minus sign