INTEL CORPORATION ETHEREXPRESS PRO/100 LAN+MODEM 56 PC CARD Card Type Modem, Fax, Network Interface Card NIC Type Ethernet Chip Set Unidentified Boot ROM Not available Network Transfer Rate 100Mbps/10Mbps Topology Linear Bus, Star Wiring Type RJ-45 Unshielded twisted pair Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 212A ITU-T V.22, V.22bis, V.23, V.32, V.32bis, V.32ter, V.34, K56flex Fax Modulation Protocol ITU-T V.17, V.27ter, V.29 Error Correction/Compression V.42, V.42bis, MNP5 Fax Class Class I Data Bus PCMCIA 55020 SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, C, E, F, H, M, P, Q, T, V, W, X, Y &B, &C, &G, &V, &Z Extended AT Commands \J, \N, \T %C S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S30 Special Commands +MS, -C Note: See MHI Help File for full command documentation. Proprietary AT Command Set AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Auto-mode detection disabled N1 In originate mode, handshake begins at line speed designated by the S37 register. Modem can shift to a slower speed if necessary. In answer mode, handshake attempted with the following protocols in order - V.FC, V.32bis, V.32, V.22bis, V.22 or Bell 212, V.21, and Bell 103 AUXILIARY RELAY Type: Configuration Format: AT [cmds] &Jn [cmds] Description: Controls the auxiliary relay Command Jack Type &J0 Auxiliary relay never closed &J1 Not supported (returns ERROR) COMMUNICATION PROTOCOLS Type: Configuration Format: AT [cmds] Bn [cmds] Description: Selects the communication protocol for data calls Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. Command Protocol B0 ITU-T V.22 at 1200bps B1 Bell 212A at 1200bps B2 Disable V.23 reverse channel B3 V.23 reverse channel B15 V.21 at 300bps B16 Bell 103J at 300bps COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Asynchronous mode &M1 Reserved &M2 Reserved &M3 Reserved &M4 Reserved COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Qn [cmds] Description: Selects communications mode options Command Mode &Q0 Buffered asynchronous mode &Q1 Reserved &Q2 Reserved &Q3 Reserved &Q4 Reserved &Q5 Error correction mode &Q6 Buffered asynchronous mode &Q7 Reserved DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Note: The action each variant of &D causes depends on the setting of &Q Command Function &D0 Modem does not respond to DTR &D1 Modem goes to command mode after DTR goes is off &D2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. &D3 Modem is initialized after DTR goes off DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D^ Disable calling tone transmission D$ Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &F [cmds] Description: Sets values in active profile to values found in the default profile Command Function &F0 Recall factory settings as active configuration &F5 Recall factory settings appropriate for ETC mode as active configuration FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K1 Reserved &K2 Reserved &K3 RTS/CTS flow control enabled &K4 XON/XOFF flow control enabled HARD RESET Type: Configuration Format: AT [cmds] &Yn [cmds] Description: Select stored profile for hard reset Command Function &Y0 Select profile 0 ON-LINE Type: Immediate Format: AT [cmds] On [cmds] Description: Controls on-line command (data transmission) state options. Note: The O command must be placed at the end of the command string. Command Function O0 On-line command mode with no retraining enabled O1 On-line command mode with retraining enabled O2 Rate negotiation then return to online data mode PULSE DIALING RATIO Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 39/61ms at 10pps (North America) &P1 33/67ms at 10pps (Europe) &P2 39/61ms at 20pps REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports modem controller firmware revision I1 Reports ROM checksum I2 Tests and reports ROM checksum I3 Reports modem controller firmware revision I12 Reports country code SOFT RESET Type: Immediate Format: AT [cmds] Zn [cmds] Description: Restores modem profiles previously saved in non-volatile RAM using the &W command. Command Function Z0 Restore setting 0 SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Note: Performs no function. Listed for compatibility only. STORE ACTIVE PROFILE Type: Configuration Format: AT [cmds] &Wn [cmds] Description: Writes the values for the active profile into the non-volatile RAM Command Function &W0 Write the active profile to stored profile 0 TEST MODES Type: Immediate Format: AT [cmds] &Tn Description: Selects test options Command Function &T0 End current test &T1 Begin local analog loopback test &T3 Begin local digital loopback &T6 Request remote digital loopback Extended AT Commands BLACKLIST Type: Configuration Format: AT [cmds] %Bn [cmds] Description: Display the numbers for which the last call attempted in the past two hour failed BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal Command \K5 Send break with Send break with Break sent with transmitted data transmitted data received data to the DTE COUNTRY OF INSTALLATION Type: Configuration Format: AT [cmds] +GCIn [cmds] Description: Configures the modem for the country of use T.35 code Country 09 Australia 0A Austria 0F Belgium 20 Canada 26 China 31 Denmark 3C Finland 3D France 04 Germany 50 Hong Kong 54 Indonesia 57 Ireland 59 Italy 00 Japan 61 Korea 6C Malaysia 7B Netherlands 7E New Zealand 82 Norway 8B Portugal 9C Singapore A0 Spain A5 Sweden A6 Switzerland FE Taiwan A9 Thailand B4 United Kingdom B5 United States FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] \Qn [cmds] Description: Sets type of flow control used by modem Command Function \Q0 Flow control disabled \Q1 Bidirectional XON/XOFF flow control enabled \Q3 Bidirectional RTS/CTS flow control enabled MANUFACTURER IDENTIFICATION Type: Configuration Format: AT [cmds] +GMIn [cmds] Description: Displays information text identifying the manufacturer of the modem mCAPABILITIES LIST Type: Configuration Format: AT [cmds] +GCAPn [cmds] Description: Displays basic capabilities of the modem. MODEM IDENTIFICATION Type: Configuration Format: AT [cmds] +GMMn [cmds] Description: Displays information text identifying the modem model REVISION IDENTIFICATION Type: Configuration Format: AT [cmds] +GMRn [cmds] Description: Displays information text indentifying the revision level of the firmware of the modem S(status) -REGISTERS BIT-MAPPED REGISTER S40 Format AT [cmds] S40=n [cmds] Description: Controls the startup rate Bit Function 0 Startup with normal autorating 1 Startup with initial rate of 4800 or below 2 Startup with initial rate of 9600 or below BIT-MAPPED REGISTER S42 Format AT [cmds] S42=n [cmds] Description: V.32bis and V.22bis auto rate contol Bit Function 0 Auto rate disabled 1 Auto rate enabled BIT-MAPPED REGISTER S43 Format AT [cmds] S43=n [cmds] Description: V.32bis auto mode control Bit Function 0 Auto mode disabled 1 Auto mode enabled CABLE DETECTION Type: Register Format: AT [cmds] S98=n [cmds] Description: Controls the automatic detection and reporting of changes in the cable or minidock attached to the modem Bit Function 0 Disables cable detection and reporting 1 Enable cable detection; disable reporting 2 Enable cable detection and reporting DATA CALLING TONE Type: Register Format: AT [cmds] S35=n [cmds] Description: Controls the data calling tone Command Function S35=0 Data calling tone disabled S35=1 Data calling tone enabled DCE LINE SPEED Type: Register Format AT [cmds] S37=n [cmds] Description: Sets the maximum allowable data exchange rate attempted during handshake process. Command Function S37=0 Maximum modem speed S37=1 Reserved S37=2 1200/75bps S37=3 300bps S37=4 Reserved S37=5 1200bps S37=6 2400bps S37=7 4800bps S37=8 7200bps S37=9 9600bps S37=10 12.0Kbps S37=11 14.4Kbps S37=12 16.8Kbps S37=13 19.2Kbps S37=14 21.6Kbp S37=15 24.0Kbp S37=16 26.4Kbp S37=17 28.8Kbps S37=18 31.2Kbp S37=19 33.6Kbp DIRECT CONNECT TRANSMIT LEVEL Type: Register Format: AT [cmds] S92=n [cmds] Default: Unidentified Range: 0 Unit: dB Description: Sets the transmit level for direct connect cellular. ERROR CORRECTION/COMPRESSION Type: Register Format: AT [cmds] S46=n [cmds] Description: Selects active error correction and compression protocols Command Function S46=0 Data compression disabled S46=2 Data compression enabled S46=136 Data compression disabled S46=138 Data compression enabled EXTENDED RESULT CODES Type: Register Format AT [cmds] S95=n [cmds] Default: 0 Range: 0-255 Unit: Bit-mapped Description: Works in combination with the Wn command to enable extended result codes. Features enabled by S95 take precedence over the options selected by Wn. Bit Function 0 Disables extended result code messages 1 Use DCE speed when reporting CONNECT result codes 2 Append "/ARQ" to CONNECT result code when an error-controlled connection is established 4 Enable CARRIER result codes 8 Enable PROTOCOL result codes 32 Enable compression result codes FEATURE NEGOTIATION OPTIONS Type: Register Format: AT [cmds] S48=n [cmds] Description: Selects active error correction and compression protocols Command Function S48=7 Detection negotiation and XID negotiation enabled S48=128 Fall-back to options set in S36 LINE TRANSMIT LEVEL Type: Register Format: AT [cmds] S91=n [cmds] Default: 6 - 15 Range: 15 Unit: dB Description: Specifies the line transmit level MODULATION ENABLE Format AT [cmds] S28=n [cmds] Unit: Bit-mapped Description: Controls V.34 modulation Bit Function 0 Disable V.34 modulation 1 Enable V.34 modulation NEGOTIATION FALLBACK Type: Register Format: AT [cmds] S36=n [cmds] Description: Sets the negotiation fallback Command Function S36=0,2 Hang up S36=1,3 Fall back to an asynchronous connection S36=4,6 Attempt MNP. If MNP fails, disconnect S36=5,7 Attempt MNP. If MNP fails, fall back to asynchronous SLEEP MODE TIMER Type: Register Format AT [cmds] S89? [cmds] Description: Displays the number of seconds of inactivity before the modem places itself into standby mode. THROUGHPUT LIMIT Type: Register Format: AT [cmds] S34=n [cmds] Default: 0 Range: 0 - 1 Unit: ASCII Description: Controls the modem throughput Command Function S34=0 Do not limit the throughput S34=1 Throughput limited to DTE speed