MOTOROLA, INC. PREMIER 33.6 INTERNAL Card Type Modem (asynchronous) Chip Set Unidentified Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.42, V.32bis, V.32, V.22bis, V.21 Fax Modulation Protocol ITU-T V.21CH2, V.27ter, V.29, V.17 Error Correction/Compression MNP5, V.42/V.42bis Fax Class Class I & II Data Bus 8-bit ISA Card Size Half-length, full-height card [Image] CONNECTIONS Function Label Function Label Line in CN1 Line out CN2 PLUG & PLAY Setting SW2/1 SW2/2 SW2/3 SW2/4 Manual On On Off Off Plug and Play Off Off On On COM PORT SELECTION Setting SW1/1 SW1/2 COM1 On On COM2 On Off COM3 Off On COM4 Off Off INTERRUPT Setting SW1/3 SW1/4 SW1/5 SW1/6 IRQ2 On Off Off Off IRQ3 Off On Off Off IRQ4 Off Off On Off IRQ5 Off Off Off On DIAGNOSTIC LED(S) LED Color Status Condition AA Unidentified On Auto-answer enabled AA Unidentified Off Auto-answer disabled AA Unidentified Blinking Phone is ringing RD Unidentified On Computer is receiving data from the modem RD Unidentified Off Computer is not receiving data from the modem SD Unidentified On Computer is transmitting data to the modem SD Unidentified Off Computer is not transmitting data to the modem CD Unidentified On Carrier signal detected CD Unidentified Off Carrier signal not detected OH Unidentified On Modem is off-hook OH Unidentified Off Modem is on-hook HS Unidentified On Modem is operating at 16800, 19200, 21600, 28800, or 33600bps HS Unidentified Off Modem is operating at 4800, 7200, 9600, 12000, 14400bps TR Unidentified On DTR signal is high TR Unidentified Off DTR signal is low MR Unidentified On Power is on MR Unidentified Off Power is off SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, E, O, S, V, X, Y, Z &G, &L, &T, &W, &X, &Y, &Z Extended AT Commands \A, \G, \X S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S25, S26 Note: See MHI Help File for full command documentation. Proprietary AT Command Set DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DP Pulse dialing enabled DR Answer mode enabled; originate mode disabled following handshake initiation. DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. HOOK CONTROL Type: Immediate Format: AT [cmds] Hn [cmds] Description: Selects whether the modem is on-hook or off-hook Command Function H0 Modem commanded to go on-hook (hang-up) H1 Modem commanded to go off-hook (pick-up) H2 Set H command to allow cleardown H3 Set H command to disallow cleardown REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product code I1 Reports EPROM CRC value I3 Reports product version I4 Reports capability code I5 Reports disconnect reason SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting SPEAKER MODE Type: Configuration Format: AT [cmds] Mn [cmds] Description: Selects various speaker options Command Function M0 Speaker disabled M1 Speaker enabled until carrier signal detected M3 Speaker enabled following dialing, then disabled after carrier signal detected. RESULT CODES Type: Configuration Format: AT [cmds] Qn [cmds] Description: Enables modem to send result codes to the DTE Command Function Q0 Result code sending enabled Q1 Result code sending disabled Q2 Result code sending in originate mode only DATA CARRIER DETECT (DCD) Type: Configuration Format: AT [cmds] &Cn [cmds] Description: Selects whether the DCD option is enabled or disabled Command Function &C0 DCD enabled &C1 DCD enabled after carrier signal detected &C2 DCD off 5 seconds after disconnect &C3 DCD follows remote RTS DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Note: The action each variant of &D causes depends on the setting of &Q Command Function &D0 Modem does not respond to DTR &D1 Modem goes to command mode after DTR goes is off &D2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. &D3 Modem is initialized after DTR goes off &D9 DTR dials/disconnects FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &F [cmds] Description: Sets values in active profile to values found in the default profile Command Function &F0 Restore factory default 0 &F1 Restore factory default 1 COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Asynchronous dial/asynchronous data &M1 Asynchronous dial/synchronous data &M2 Dial stored number when DTR off/on transition is detected/sync data &M3 Manual dial/sync data &M4 V.25bis dialer/BISYNC protocol/sync data (EBCDIC) &M5 V.25bis dialer/SDLC protocol/sync data (NRZ) &M6 V.25bis async dial/sync data &M7 V.25bis async dial/async data &M8 V.25bis dialer w/BISYNC protocol/sync data (EBCDIC) &M9 V.25bis dialer w/SDLC protocol/sync data (EBCDIC) (NRZ) &M10 V.25bis dialer w/SDLC protocol/sync data (ASCII) (NRZI) &M11 V.25bis dialer w/SDLC protocol/sync data (EBCID) (NRZI) PULSE DIALING RATIO Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 39/61ms at 10pps (North America) &P1 33/67ms at 10pps (Europe) RTS/CTS Type: Configuration Format: AT [cmds] &Rn [cmds] Description: Selects RTS/CTS options Command Function &R0 CTS follows RTS in data mode; RTS is ignored in command mode. &R1 CTS forced high, RTS is ignored. &R2 CTS follows DCD &R9 CTS equals RTS DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high when ready to accept data &S2 DSR off for 5 seconds after disconnect &S3 DSR follows off hook CONFIGURATION PROFILES Type: Immediate Format: AT [cmds] &V [cmds] Description: Displays active and stored configuration profiles Command Function &V0 View configuration profiles &V1 Displays received signal status &V2 Displays active profile Extended AT Commands BREAK SEND Type: Configuration Format: AT [cmds] \Bn [cmds] Default: 35 Range: 1-255 Unit: 20ms Description: Sends break to modem Command Function \B0 Transmit break signal \B1 Set break length in 20ms increments AUTO-RELIABLE TIME BUFFER CONFIGURATION Type: Configuration Format: AT [cmds] \Cn [cmds] Description: Controls the handling of incoming data during auto-reliable time period Command Function \C0 Data is discarded \C1 Data is buffered LOCK SERIAL PORT Type: Configuration Format: AT [cmds] \Jn [cmds] Description: Sets operation of serial port speed Command Function \J0 Serial speed locked \J1 Serial speed follows connect speed \J2 Enable 230.4Kbps serial speed \J3 Disable 230.4Kbps serial speed BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal Command Function \K1 Break signals empty data buffers \K3 Expedite break signals \K5 Sequence break signals with data V.42 FAST DETECT Type: Configuration Format: AT [cmds] \Mn [cmds] Description: Controls the V.42 fast detect data sequence Command Function \M0 V.42 fast detect data sequence disabled \M1 V.42 fast detect data sequence enabled CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 MNP mode \N3 MNP with normal fallback \N4 LAPM only \N5 LAPM with normal fallback \N6 LAPM with MNP fallback \N7 LAPM with MNP and normal fallback FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] \Qn [cmds] Description: Sets type of flow control used by modem Command Function \Q0 Flow control disabled \Q1 Bidirectional XON/XOFF flow control enabled \Q2 CTS flow control by DCE enabled \Q3 Bidirectional RTS/CTS flow control enabled RING INDICATE Type: Configuration Format: AT [cmds] \Rn [cmds] Description: Controls the ring indicator Command Function \R0 LED AA blinks for ring and remains on during the call \R1 LED AA blinks for ring and turns off when call is answered INACTIVITY TIMER Type: Configuration Format: AT [cmds] \Tn [cmds] Range: 1-255 Unit: 1 second Description: Sets the length of time that the modem does not receive information before it disconnects. EXTENDED RESULT CODES Type: Configuration Format: AT [cmds] \Vn [cmds] Description: Selects extended result codes Command Function \V0 Connect message shows computer speed \V1 Connect message shows computer speed/protocol \V2 Connect message shows modem speed \V3 Connect message shows speed/protocol \V4 Connect message shows modem speed/modulation/protocol SPEED SELECTION Type: Configuration Format: AT [cmds] %Bn [cmds] Description: Selects the maximum connect speed Command Function %B0 Use computer speed %B1 300bps %B2 1200bps %B3 2400bps %B4 4800bps %B5 9600bps uncoded %B6 9600bps %B7 7200bps %B8 12000bps %B9 14400bps %B10 600bps %B11 16800bps %B12 19200bps %B13 21600bps %B14 24000bps %B15 26400bps %B16 28800bps %B17 31200bps %B18 33600bps COMPRESSION Type: Configuration Format: AT [cmds] %Cn [cmds] Description: Selects data compression Command Function %C0 Compression disabled %C1 Compression enabled on transmit and receive data DISCONNECT BUFFER DELAY Type: Configuration Format: AT [cmds] %Dn [cmds] Description: Controls the disconnect buffer delay Command Function %D0 Disable disconnect buffer delay %D1 Set disconnect buffer delay in seconds n (n= 1 - 255) MINIMUM SPEED SELECTION Type: Immediate Format: AT [cmds] %L [cmds] Description: Sets the minimum speed level Command Function %L0 300bps %L1 300bps %L2 1200bps %L3 2400bps %L4 4800bps %L5 9600bps uncoded %L6 9600bps %L7 7200bps %L8 12000bps %L9 14400bps %L10 600bps %L11 16800bps %L12 19200bps %L13 21600bps %L14 24000bps %L15 26400bps %L16 28800bps %L17 31200bps %L18 33600bps REMOTE CONFIGURATION Type: Immediate Format: AT [cmds] %P [cmds] Description: Displays the remote configuration code AUTOMATIC RATE ADAPTION Type: Immediate Format: AT [cmds] %Rn [cmds] Description: Send PTT test signals for a line tests Command Function %R0 Disable automatic rate adaption %R1 Enable automatic rate adaption low BER %R2 Enable automatic rate adaption medium BER %R3 Enable automatic rate adaption using high BER TEST PATTERN Type: Immediate Format: AT [cmds] %Tn [cmds] Description: Transmit test pattern PRODUCT REVISION Type: Immediate Format: AT [cmds] %Vn [cmds] Description: Display product revision level V.34 ASYMMETRIC RATE Type: Immediate Format: AT [cmds] *ASn [cmds] Description: Sets the asymmetric bit rate Command Function *AS0 Disable V.34 asymmetric bit rate *AS1 Enable V.34 asymmetric bit rate BILTERAL DIGITAL LOOP Type: Immediate Format: AT [cmds] *DGn [cmds] Description: Controls the bilateral digital loop Command Function *DG0 Disables the bilateral digital loop *DG1 Enables the digital bilateral loop TEST MODE - PTT Type: Immediate Format: AT [cmds] *DNn [cmds] Description: Send PTT test signals for a line tests Command Function *DN0 Allow redial with A/ *DN1 Disallow redial with A/ DISTINCTIVE RING DETECTION Type: Immediate Format: AT [cmds] *DRn [cmds] Description: Controls the distinctive ring detection Command Function *DR0 Disable distinctive ring detection *DR1 Enable distinctive ring detection FAST TRAIN Type: Immediate Format: AT [cmds] *FTn [cmds] Description: Controls the fast train Command Function *FT0 Disables the fast train *FT1 Enables the fast train CALLER ID Type: Immediate Format: AT [cmds] *IDn [cmds] Description: Controls the caller ID function Command Function *ID0 Disable caller ID *ID1 Enable caller ID MODULATION Type: Immediate Format: AT [cmds] *MMn [cmds] Description: Sets the modulation Command Function *MM0 Automode *MM1 V.21 *MM2 Bell 103J *MM3 V.23 *MM4 Bell 212A *MM5 V.22bis *MM11 V.32bis *MM12 V.34 STORED NUMBERS Type: Immediate Format: AT [cmds] *ND [cmds] Description: Displays the nine stored numbers AT COMMANDSET Type: Immediate Format: AT [cmds] *NTn [cmds] Description: Controls the AT command set Command Function *NT0 AT command set disabled *NT1 AT command set enabled MODE SELECTION Type: Immediate Format: AT [cmds] *ORn [cmds] Description: Controls the originate or answer mode Command Function *OR0 Originate mode active *OR1 Answer mode active RATE NEGOTIATION SELECTION Type: Immediate Format: AT [cmds] *RRn [cmds] Description: Sets the rate negotiation Command Function *RR0 Rate negotiation to 2400 *RR1 Rate negotiation to 4800 *RR2 Rate negotiation to 7200 *RR3 Rate negotiation to 9600 *RR4 Rate negotiation to 12000 *RR5 Rate negotiation to 14400 *RR6 Rate negotiation to 16800 *RR7 Rate negotiation to 19200 *RR8 Rate negotiation to 21600 *RR9 Rate negotiation to 24000 *RR10 Rate negotiation to 26400 *RR11 Rate negotiation to 28800 *RR12 Rate negotiation to 31200 *RR13 Rate negotiation to 33600 RATE ADAPTION Type: Immediate Format: AT [cmds] *RUn [cmds] Description: Controls the rate adaption Command Function *RU0 Disable auto rate adaption above initial rate *RU1 Enable auto rate adaption above initial rate TRANSMIT LEVEL Type: Immediate Format: AT [cmds] *TDn [cmds] Description: Set dial transmit level from -9 to -30dBm RATE SELECTION THRESHOLD Type: Immediate Format: AT [cmds] *THn [cmds] Description: Sets the rate selection threshold Command Function *TH0 Low V.34 rate selection threshold *TH1 Medium V.34 rate selection threshold *TH2 High V.34 rate selection threshold LEASED LINE TRANSMIT LEVEL Type: Immediate Format: AT [cmds] *TLn [cmds] Description: Sets the leased line transmit level (0 - 30) ONLINE HELP Type: Immediate Format: AT [cmds] $Hn [cmds] Description: Online help Command Function $H=string Online help PRODUCT SERIAL NUMBER Type: Immediate Format: AT [cmds] $Vn [cmds] Description: Displays the product serial number Security Commands USER CALLBACK NUMBER Type: Immediate Format: AT [cmds] $Cn=m [cmds] Description: Sets the user callback number (n= user number and m= the callback number SECURITY DISABLED Type: Immediate Format: AT [cmds] $D [cmds] Description: Disables security SECURITY STATUS Type: Immediate Format: AT [cmds] $D? [cmds] Description: Reports the security status SECURITY ENABLE Type: Immediate Format: AT [cmds] $EH=pw [cmds] Description: Enables security (pw=superuser password) REINITIALIZE SECURITY Type: Immediate Format: AT [cmds] $F=pw$pw [cmds] Description: Reinitializes security (pw=superuser password) USER INFORMATION Type: Immediate Format: AT [cmds] $I [cmds] Description: Reports all secure user information SECURITY LEVEL Type: Immediate Format: AT [cmds] $Ln=m [cmds] Description: Set security level for the user specified by n ILLEGAL ATTEMPTS INFORMATION Type: Immediate Format: AT [cmds] $M [cmds] Description: Reports illegal attempts information RESET ALL ILLEGAL ATTEMPTS Type: Immediate Format: AT [cmds] $M* [cmds] Description: Reset all illegal attempts registers/restore suspended users to normal status RESET ILLEGAL ATTEMPTS Type: Immediate Format: AT [cmds] $Mn [cmds] Description: Reset illegal attempts registers/restore suspended users to normal status LOCAL LOGON Type: Immediate Format: AT [cmds] $n=pw [cmds] Description: Local logon (n = user number, pw = password) SET PASSWORD Type: Immediate Format: AT [cmds] $Pn=pw$pw [cmds] Description: Set user password (n = user number, pw = new password, n = 0 for superuser password) REMOVE USER Type: Immediate Format: AT [cmds] $Rn [cmds] Description: Removes a user SUPERUSER STATUS Type: Immediate Format: AT [cmds] $S=pw [cmds] Description: Request superuser status (pw = password) CURRENT USER STATUS Type: Immediate Format: AT [cmds] $S? [cmds] Description: Reports current user status LOCAL LOGON Type: Immediate Format: AT [cmds] $n=m [cmds] Description: Local logon (n = user number and m = password) Remote Configuration Commands REMOTE CONFIGURATION SECURITY Type: Immediate Format: AT [cmds] %P=n [cmds] Description: Set the remote configuration security code to value n DISPLAY SECURITY CODE Type: Immediate Format: AT [cmds] %P? [cmds] Description: Displays the remote configuration security code CLEAR SECURITY CODE Type: Immediate Format: AT [cmds] %P = (blank) [cmds] Description: Clears the security code COMPUTER SPEED Type: Immediate Format: AT [cmds] *RBn [cmds] Description: Sets the remote configuration computer speed Command Function *RB0 300bps *RB1 600bps *RB2 1200bps *RB3 2400bps *RB4 4800bps *RB5 7200bps *RB6 9600bps *RB7 12000bps *RB8 14400bps *RB9 16800bps *RB10 19200bps *RB11 21600bps *RB12 24000bps *RB13 26400bps *RB14 28800bps *RB15 28400bps *RB16 57600bps *RB17 115200bps FORMAT SETTINGS Type: Immediate Format: AT [cmds] *RFn [cmds] Description: Sets the remote configuration format settings Command Function *RF0 7 data bits, mark parity, 1 stop bit *RF1 7 data bits, no parity, 2 stop bit *RF2 7 data bits, odd parity, 1 stop bit *RF3 7 data bits, even parity, 1 stop bit *RF4 8 data bits, mark parity, 1 stop bit *RF5 8 data bits, no parity, 1 stop bit *RF6 8 data bits, odd parity, 1 stop bit *RF7 8 data bits, even parity, 1 stop bit SAVE REMOTE CONFIGURATION Type: Immediate Format: AT [cmds] *RQn [cmds] Description: Exit remote configuration and saves or discards the new configuration Command Function *RQ0 Save new configuration *RQ1 Discard new configuration S(status) -REGISTERS REMOTE ESCAPE CHARACTER Format AT [cmds] S41=n [cmds] Default: 61 Range: 1-255 Unit: 20ms Description: Sets the remote escape character REMOTE GUARD TIME Format AT [cmds] S42=n [cmds] Default: 50 Range: 0-255 Unit: ASCII Description: Sets the remote guard time COMPUTER CONTROL CHARACTER - XON Format AT [cmds] S44=n [cmds] Default: 17 Range: 0-127 Unit: ASCII Description: Sets the character used to represent XON for the computer COMPUTER CONTROL CHARACTER - XOFF Format AT [cmds] S45=n [cmds] Default: 19 Range: 0-127 Unit: ASCII Description: Sets the character used to represent XOFF for the computer MODEM CONTROL CHARACTER - XON Format AT [cmds] S49=n [cmds] Default: 17 Range: 0-127 Description: Sets the character used to represent XON for the modem MODEM CONTROL CHARACTER - XOFF Format AT [cmds] S50=n [cmds] Default: 19 Range: 0-127 Unit: ASCII Description: Sets the character used to represent XOFF for the modem PASSWORD TIMEOUT SECURITY Format AT [cmds] S73=n [cmds] Default: 0 Range: 0-255 Description: Sets the password timeout security CALLBACK DELAY Format AT [cmds] S74=n [cmds] Default: 15 Range: 0-255 Description: Sets the callback delay CALLBACK RETRY Format AT [cmds] S75=n [cmds] Default: 0 Range: 0-255 Description: Sets the callback retry CALLBACK RETRY DELAY Format AT [cmds] 76=n [cmds] Default: 15 Range: 1-255 Description: Sets the callback retry delay LOCKOUT THRESHOLD Format AT [cmds] S77=n [cmds] Default: 0 Range: 0-255 Description: Sets the lockout threshold