MOTOROLA, INC. PREMIER 33.6 EXTERNAL Card Type Modem (asynchronous) Chip Set Unidentified Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.34, V.32bis, V.32, V.22bis, V.21 Fax Modulation Protocol ITU-T V.21 CH2, V.27ter, V.29, V.17 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I Data Bus External [Image] CONNECTIONS Function Label Function Label Line in CN1 DC power CN4 Line out CN2 Restore factory SW1 defaults switch RS-232/422 serial port CN3 Power switch SW2 DIAGNOSTIC LED(S) LED Color Status Condition AA Unidentified On Auto-answer enabled AA Unidentified Off Auto-answer disabled AA Unidentified Blinking Incoming call detected RD Unidentified On Computer is receiving data from the modem RD Unidentified Off Computer is not receiving data from the modem SD Unidentified On Computer is transmitting data to the modem SD Unidentified Off Computer is not transmitting data to the modem CD Unidentified On Carrier signal detected CD Unidentified Off Carrier signal not detected OH Unidentified On Modem is off-hook OH Unidentified Off Modem is on-hook HS Unidentified On Modem is operating at 16800, 19200, 21600, 28800, or 33600bps HS Unidentified Blinking Modem is operating at 300, 1200, or 2400bps HS Unidentified Off Modem is operating at 4800, 7200, 9600, 12000, 14400bps TR Unidentified On DTR signal is high TR Unidentified Off DTR signal is low MR Unidentified On Power is on MR Unidentified Off Power is off SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, E, O, V, X, Y, Z &G, &L, &T, &W, &X, &Y, &Z Extended AT Commands \A, \G, \X S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S25, S26 Note: See MHI Help File for full command documentation. Proprietary AT Command Set DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DP Pulse dialing enabled DR Answer mode enabled; originate mode disabled following handshake initiation. DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. HOOK CONTROL Type: Immediate Format: AT [cmds] Hn [cmds] Description: Selects whether the modem is on-hook or off-hook Command Function H0 Modem commanded to go on-hook (hang-up) H1 Modem commanded to go off-hook (pick-up) H2 Set H command to allow cleardown H3 Set H command to disallow cleardown REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product code I1 Reports EPROM CRC value I3 Reports product version I4 Reports capability code I5 Reports disconnect reason SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting SPEAKER MODE Type: Configuration Format: AT [cmds] Mn [cmds] Description: Selects various speaker options Command Function M0 Speaker disabled M1 Speaker enabled until carrier signal detected M3 Speaker enabled following dialing, then disabled after carrier signal detected. RESULT CODES Type: Configuration Format: AT [cmds] Qn [cmds] Description: Enables modem to send result codes to the DTE Command Function Q0 Result code sending enabled Q1 Result code sending disabled Q2 Result code sending in originate mode only DATA CARRIER DETECT (DCD) Type: Configuration Format: AT [cmds] &Cn [cmds] Description: Selects whether the DCD option is enabled or disabled Command Function &C0 DCD enabled &C1 DCD enabled after carrier signal detected &C2 DCD off 5 seconds after disconnect &C3 DCD follows remote RTS DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Note: The action each variant of &D causes depends on the setting of &Q Command Function &D0 Modem does not respond to DTR &D1 Modem goes to command mode after DTR goes is off &D2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. &D3 Modem is initialized after DTR goes off &D9 DTR dials/disconnects FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &F [cmds] Description: Sets values in active profile to values found in the default profile Command Function &F0 Restore factory default 0 &F1 Restore factory default 1 COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Asynchronous dial/asynchronous data &M1 Asynchronous dial/synchronous data &M2 Dial stored number when DTR off/on transition is detected/sync data &M3 Manual dial/sync data &M4 V.25bis dialer/BISYNC protocol/sync data (EBCDIC) &M5 V.25bis dialer/SDLC protocol/sync data (NRZ) &M6 V.25bis async dial/sync data &M7 V.25bis async dial/async data &M8 V.25bis dialer w/BISYNC protocol/sync data (EBCDIC) &M9 V.25bis dialer w/SDLC protocol/sync data (EBCDIC) (NRZ) &M10 V.25bis dialer w/SDLC protocol/sync data (ASCII) (NRZI) &M11 V.25bis dialer w/SDLC protocol/sync data (EBCID) (NRZI) PULSE DIALING RATIO Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 39/61ms at 10pps (North America) &P1 33/67ms at 10pps (Europe) RTS/CTS Type: Configuration Format: AT [cmds] &Rn [cmds] Description: Selects RTS/CTS options Command Function &R0 CTS follows RTS in data mode; RTS is ignored in command mode. &R1 CTS forced high, RTS is ignored. &R2 CTS follows DCD &R9 CTS equals RTS DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high when ready to accept data &S2 DSR off for 5 seconds after disconnect &S3 DSR follows off hook CONFIGURATION PROFILES Type: Immediate Format: AT [cmds] &V [cmds] Description: Displays active and stored configuration profiles Command Function &V0 View configuration profiles &V1 Displays received signal status &V2 Displays active profile Extended AT Commands BREAK SEND Type: Configuration Format: AT [cmds] \Bn [cmds] Default: 35 Range: 1-255 Unit: 20ms Description: Sends break to modem Command Function \B0 Transmit break signal \B1 Set break length in 20ms increments AUTO-RELIABLE TIME BUFFER CONFIGURATION Type: Configuration Format: AT [cmds] \Cn [cmds] Description: Controls the handling of incoming data during auto-reliable time period Command Function \C0 Data is discarded \C1 Data is buffered LOCK SERIAL PORT Type: Configuration Format: AT [cmds] \Jn [cmds] Description: Sets operation of serial port speed Command Function \J0 Serial speed locked \J1 Serial speed follows connect speed \J2 Enable 230.4Kbps serial speed \J3 Disable 230.4Kbps serial speed BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal Command Function \K1 Break signals empty data buffers \K3 Expedite break signals \K5 Sequence break signals with data V.42 FAST DETECT Type: Configuration Format: AT [cmds] \Mn [cmds] Description: Controls the V.42 fast detect data sequence Command Function \M0 V.42 fast detect data sequence disabled \M1 V.42 fast detect data sequence enabled CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 MNP mode \N3 MNP with normal fallback \N4 LAPM only \N5 LAPM with normal fallback \N6 LAPM with MNP fallback \N7 LAPM with MNP and normal fallback FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] \Qn [cmds] Description: Sets type of flow control used by modem Command Function \Q0 Flow control disabled \Q1 Bidirectional XON/XOFF flow control enabled \Q2 CTS flow control by DCE enabled \Q3 Bidirectional RTS/CTS flow control enabled RING INDICATE Type: Configuration Format: AT [cmds] \Rn [cmds] Description: Controls the ring indicator Command Function \R0 LED AA blinks for ring and remains on during the call \R1 LED AA blinks for ring and turns off when call is answered INACTIVITY TIMER Type: Configuration Format: AT [cmds] \Tn [cmds] Range: 1-255 Unit: 1 second Description: Sets the length of time that the modem does not receive information before it disconnects. EXTENDED RESULT CODES Type: Configuration Format: AT [cmds] \Vn [cmds] Description: Selects extended result codes Command Function \V0 Connect message shows computer speed \V1 Connect message shows computer speed/protocol \V2 Connect message shows modem speed \V3 Connect message shows speed/protocol \V4 Connect message shows modem speed/modulation/protocol SPEED SELECTION Type: Configuration Format: AT [cmds] %Bn [cmds] Description: Selects the maximum connect speed Command Function %B0 Use computer speed %B1 300bps %B2 1200bps %B3 2400bps %B4 4800bps %B5 9600bps uncoded %B6 9600bps %B7 7200bps %B8 12000bps %B9 14400bps %B10 600bps MOTOROLAPREMIER 33.6 EXTERNAL. . . continued from previous pagePRODUCT REVISION__Type:_Immediate__Format:_AT [cmds] %Vn [cmds]__Description:_Display product revision level__Special AT CommandsV.34 ASYMMETRIC RATE__Type:_Immediate__Format:_AT [cmds] *ASn [cmds]__Description:_Sets the asymmetric bit rate__ Command_Function__ *AS0_Disable V.34 asymmetric bit rate__ *AS1_Enable V.34 asymmetric bit rate__BILTERAL DIGITAL LOOP__Type:_Immediate__Format:_AT [cmds] *DGn [cmds]__Description:_Controls the bilateral digital loop__ Command_Function__ *DG0_Disables the bilateral digital loop__ *DG1_Enables the digital bilateral loop__TEST MODE - PTT__Type:_Immediate__Format:_AT [cmds] *DNn [cmds]__Description:_Send PTT test signals for a line tests__ Command_Function__ *DN0_Allow redial with A/__ *DN1_Disallow redial with A/__DISTINCTIVE RING DETECTION__Type:_Immediate__Format:_AT [cmds] *DRn [cmds]__Description:_Controls the distinctive ring detection__ Command_Function__ *DR0_Disable distinctive ring detection__ *DR1_Enable distinctive ring detection__FAST TRAIN__Type:_Immediate__Format:_AT [cmds] *FTn [cmds]__Description:_Controls the fast train__ Command_Function__ *FT0_Disables the fast train__ *FT1_Enables the fast train__Continued on next page . . . MOTOROLAPREMIER 33.6 EXTERNAL. . . continued from previous pageONLINE HELP__Type:_Immediate__Format:_AT [cmds] $Hn [cmds]__Description:_Online help__ Command_Function__ $H=string_Online help__PRODUCT SERIAL NUMBER__Type:_Immediate__Format:_AT [cmds] $Vn [cmds]__Description:_Displays the product serial number__Security CommandsUSER CALLBACK NUMBER__Type:_Immediate__Format:_AT [cmds] $Cn=m [cmds]__Description:_Sets the user callback number (n= user number and m= the callback number__SECURITY DISABLED__Type:_Immediate__Format:_AT [cmds] $D [cmds]__Description:_Disables security__SECURITY STATUS__Type:_Immediate__Format:_AT [cmds] $D? [cmds]__Description:_Reports the security status__SECURITY ENABLE__Type:_Immediate__Format:_AT [cmds] $EH=pw [cmds]__Description:_Enables security (pw=superuser password)__REINITIALIZE SECURITY__Type:_Immediate__Format:_AT [cmds] $F=pw$pw [cmds]__Description:_Reinitializes security (pw=superuser password)__USER INFORMATION__Type:_Immediate__Format:_AT [cmds] $I [cmds]__Description:_Reports all secure user information__Continued on next page . . . MOTOROLAPREMIER 33.6 EXTERNAL. . . continued from previous pageFORMAT SETTINGS__Type:_Immediate__Format:_AT [cmds] *RFn [cmds]__Description:_Sets the remote configuration format settings__ Command_Function__ *RF0_7 data bits, mark parity, 1 stop bit__ *RF1_7 data bits, no parity, 2 stop bit__ *RF2_7 data bits, odd parity, 1 stop bit__ *RF3_7 data bits, even parity, 1 stop bit__ *RF4_8 data bits, mark parity, 1 stop bit__ *RF5_8 data bits, no parity, 1 stop bit__ *RF6_8 data bits, odd parity, 1 stop bit__ *RF7_8 data bits, even parity, 1 stop bit__SAVE REMOTE CONFIGURATION__Type:_Immediate__Format:_AT [cmds] *RQn [cmds]__Description:_Exit remote configuration and saves or discards the new configuration__ Command_Function__ *RQ0_Save new configuration__ *RQ1_Discard new configuration__S(status) -REGISTERSREMOTE ESCAPE CHARACTER__Format_AT [cmds] S41=n [cmds]__Default:_61__Range:_1-255__Unit:_20ms__Description:_Sets the remote escape character__REMOTE GUARD TIME__Format_AT [cmds] S42=n [cmds]__Default:_50__Range:_0-255__Unit:_ASCII__Description:_Sets the remote guard time__COMPUTER CONTROL CHARACTER - XON__Format_AT [cmds] S44=n [cmds]__Default:_17__Range:_0-127__Unit:_ASCII__Description:_Sets the character used to represent XON for the computer__Continued on next page . . . MOTOROLAPREMIER 33.6 EXTERNAL. . . continued from previous pageCOMPUTER CONTROL CHARACTER - XOFF__Format_AT [cmds] S45=n [cmds]__Default:_19__Range:_0-127__Unit:_ASCII__Description:_Sets the character used to represent XOFF for the computer__MODEM CONTROL CHARACTER - XON __Format_AT [cmds] S49=n [cmds]__Default:_17__Range:_0-127__Description:_Sets the character used to represent XON for the modem__MODEM CONTROL CHARACTER - XOFF __Format_AT [cmds] S50=n [cmds]__Default:_19__Range:_0-127__Unit:_ASCII__Description:_Sets the character used to represent XOFF for the modem__PASSWORD TIMEOUT SECURITY__Format_AT [cmds] S73=n [cmds]__Default:_0__Range:_0-255__Description:_Sets the password timeout security__CALLBACK DELAY__Format_AT [cmds] S74=n [cmds]__Default:_15__Range:_0-255__Description:_Sets the callback delay__CALLBACK RETRY__Format_AT [cmds] S75=n [cmds]__Default:_0__Range:_0-255__Description:_Sets the callback retry__CALLBACK RETRY DELAY__Format_AT [cmds] 76=n [cmds]__Default:_15__Range:_1-255__Description:_Sets the callback retry delay__LOCKOUT THRESHOLD__Format_AT [cmds] S77=n [cmds]__Default:_0__Range:_0-255__Description:_Sets the lockout threshold__