SHARK MULTIMEDIA BASKING COMBO Card Type Modem (asynchronous), Sound card Chip Set Unidentified I/O Options Line in, microphone, speaker out, game/MIDI port Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.21, V.22A/B, V.22bis, V.23, V.32, V.32bis, V.34, V.FC, K56flex Fax Modulation Protocol ITU-T V.17, V.29, V.27ter, V.33, V.21CH2 Error Correction/Compression MNP5, MNP10, V.42, V.42bis Fax Class Class I Data Bus 16-bit ISA Card Size Half-length, half-height card [Image] CONNECTIONS Function Label Function Label Line in CN1 Microphone CN4 Line out CN2 Speaker out CN5 Line in CN3 Game/MIDI port CN6 SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, E, H, M, O, P, Q, T, V, X &C, &P, &R, &V, &W, &Z Extended AT Commands \A, \B, \K, \N %C, %E Voice Commands #BDR, #CID, #TL, #VBS, #VSD, #VGT S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S18, S25, S26 Special Commands +MS Note: See MHI Help File for full command documentation. Proprietary AT Command Set AUTOMODE CONTROL Type: Immediate Format: AT [cmds] Nn [cmds] Description: Controls the automode detection Command Function N0 Disabled N1 Enabled COMMUNICATION PROTOCOLS Type: Configuration Format: AT [cmds] Bn [cmds] Description: Selects the communication protocol for data calls Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. Command Protocol B0 ITU-T V.22 at 300 or 1200bps COMPRESSION Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Selects data compression Command Function &K0 Data compression disabled &K1 MNP5 enabled &K2 V.42bis enabled &K3 MNP5 and V.42bis; or data compression and correction enabled CONNECT MESSAGE FORMAT Type: Configuration Format: AT [cmds] &An [cmds] Description: Sets the connect message format Command Function &A0 Only CONNECT message &A1 CONNECT message and modulation indicator &A2 CONNECT message, error detection protocol and data compression indicators &A3 CONNECT message, error detection protocol, data compression indicators and modulation indicator CONNECT MESSAGE SPEED SOURCE Type: Configuration Format: AT [cmds] &En [cmds] Description: Sets the requested source for the speed field in the CONNECT message. Note: Used primarily for international data transmission Command Function &E0 DCE speed &E1 DTE speed DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR follows circuit definition DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 Modem does not respond to DTR &D1 Modem goes to command mode after DTR goes is off &D2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. &D3 Modem is initialized after DTR goes off DEFAULT CONFIGURATION Type: Configuration Format: AT [cmds] Yn [cmds] Description: Sets the default configuration Command Function Y0 Select user template 0 Y1 Select user template 1 Y2 Select factory setting 0 Y3 Select factory setting 1 DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D* Tone only D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &F [cmds] Description: Sets values in active profile to values found in the default profile Command Function &F0 Select factory setting 0 &F1 Select factory setting 1 FLOW CONTROL Type: Configuration Format: AT [cmds] &Hn [cmds] Description: Sets the flow control Command Function &H0 Disable flow control &H1 Enable RTS/CTS emulation REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I1 Reports modem name, vendor number, version I2 Reports software vendor and version number I3 Reports chip vendor, ID number I4 Reports modem active profile I5 Reports stored profile 0 and active profile 0 I6 Reports stored profile 1 and active profile 1 I7 Reports stored phone numbers SOFT RESET Type: Immediate Format: AT [cmds] Zn [cmds] Description: Restores modem profiles previously saved in non-volatile RAM using the &W command. Command Function Z0 Select default user template in Y Z1 Select user template 0 Z2 Select user template 1 Z3 Select factory setting 0 Z4 Select factory setting 1 SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting TEST MODES Type: Immediate Format: AT [cmds] &Tn Description: Selects test options Command Function &T0 TBD &T1 TBD &T2 TBD &T3 TBD STANDARD AT# VOICE COMMAND SET INACTIVITY TIMER Type: Immediate Format: AT [cmds] #VIT=n [cmds] Description: Sets the inactivity timer RECEIVE GAIN Type: Immediate Format: AT [cmds] #RG=n [cmds] Description: Sets the receive gainlevel VOICE PARAMETERS Type: Immediate Format: AT [cmds] #VIP=n [cmds] Description: Initializes the voice parameters S(status) -REGISTERS ACTUAL MODULATION Type: Register Format AT [cmds] S37=n [cmds] Description: Returns the actual modulation speed ACTUAL RX SPEED Type: Register Format AT [cmds] S38=n [cmds] Description: Returns the actual RX speed ACTUAL SPEED Type: Register Format: AT [cmds] S35=n [cmds] Description: Sets the actual speed after connect ADPCM Type: Register Format: AT [cmds] S76=n [cmds] Default: 4 Range: 4, 8, 16 Description: Controls the ADPCM bits per sample ANSWER DELAY Type: Register Format: AT [cmds] S92=n [cmds] Default: 2 Range: 0-255 Description: Controls the answer delay AUTO ANSWER Format AT [cmds] S27=n [cmds] Default: 8 Range: 0-255 Unit: 1 second Description: Sets the auto answer clear timeout AUTOMODE SELECT Format: AT [cmds] S31=n [cmds] Default: 1 Range: 0-3 Description: Sets automode BEEP TONE TIMER Type: Register Format: AT [cmds] S77=n [cmds] Default: 10 Range: 0-40 Description: Sets the beep tone timer BREAK LENGTH Format AT [cmds] S21=n [cmds] Default: 9 Range: 0-9 Description: Sets the break length CD Type: Register Format: AT [cmds] S60=n [cmds] Default: 1 Range: 0-1 Description: Sets the CD setting CID Type: Register Format: AT [cmds] S75=n [cmds] Default: 0 Range: 0,1 Description: Controls the CID CIRCUIT 106 Type: Register Format: AT [cmds] S66=n [cmds] Default: 0 Range: 0-1 Description: Sets the circuit 106 (RTS) CIRCUIT 107 Type: Register Format: AT [cmds] S67=n [cmds] Default: 0 Range: 0-1 Description: Sets the circuit 107 (DSR) CIRCUIT 109 Type: Register Format: AT [cmds] S68=n [cmds] Default: 0 Range: 0-1 Description: Sets the circuit 109 (CD) CONNECT MESSAGE Type: Register Format: AT [cmds] S70=n [cmds] Default: 0 Range: 0-1 Description: Sets the CONNECT message format CONNECT MESSAGE Type: Register Format: AT [cmds] S71=n [cmds] Default: 0 Range: 0-1 Description: Sets the CONNECT message speed source COUNTRY TYPE Type: Register Format: AT [cmds] S162=n [cmds] Default: 1 Range: 0-25 Description: Sets the country type CURRENT SETTING Type: Register Format: AT [cmds] S59=n [cmds] Default: 3 Range: 0-5 Description: Sets the current setting DATA PUMP STATUS Type: Register Format AT [cmds] S36=n [cmds] Description: Displays the current data pump status DEFAULT SETTING Type: Register Format: AT [cmds] S161=n [cmds] Default: 2 Range: 0-1 Description: Sets the default setting DSR Type: Register Format: AT [cmds] S64=n [cmds] Default: 0 Range: 0-1 Description: Sets the DSR DTMF HIGH GAIN Type: Register Format: AT [cmds] S156=n [cmds] Default: 0 Range: 0-255 Description: Sets the DTMF high gain level DTMF LOW GAIN Type: Register Format: AT [cmds] S155=n [cmds] Default: 0 Range: 0-255 Description: Sets the DTMF low gain level DTMF TONE Type: Register Format: AT [cmds] S84=n [cmds] Default: 0 Range: 0-3F Description: Controls the DTMF tone reports cap 0 DTMF TONE Type: Register Format: AT [cmds] S85=n [cmds] Default: 0 Range: 0-3F Description: Controls the DTMF tone reports cap 1 DTMF TONE Type: Register Format: AT [cmds] S86=n [cmds] Default: 0 Range: 0-3F Description: Controls the DTMF tone reports cap 2 DTR Type: Register Format: AT [cmds] S63=n [cmds] Default: 0 Range: 0-3 Description: Sets the DTR ECHO Type: Register Format AT [cmds] S13=n [cmds] Default: 1 Range: 0-1 Description: Sets the echo EXTENDED CODE Type: Register Format: AT [cmds] S56=n [cmds] Default: 4 Range: 0-4 Description: Sets the extended code FAE VALUE Type: Register Format: AT [cmds] S151=n [cmds] Default: 0 Range: 0,1 Description: Sets the FAE value FCLASS VALUE Type: Register Format: AT [cmds] S150=n [cmds] Default: 0 Range: 0,1,8 Description: Sets the FCLASS value FLASH TIMER Type: Register Format AT [cmds] S24=n [cmds] Default: 20 Range: 0-255 Unit: 10 ms Description: Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. FLASH TIMER Type: Register Format: AT [cmds] S140=n [cmds] Range: 0-255 Description: Sets the duration of the flash timer FLOW CONTROL Type: Register Format: AT [cmds] S62=n [cmds] Default: 1 Range: 0-3 Description: Sets the flow control FLOW CONTROL CHARACTER - XOFF Type: Register Format AT [cmds] S23=n [cmds] Default: 19 Range: 0-127 Description: Sets the XOFF character HANDSET GAIN Type: Register Format: AT [cmds] S72=n [cmds] Default: 80 Range: 0-255 Description: Sets the handset record gain control HSET OUT GAIN Type: Register Format: AT [cmds] S154=n [cmds] Range: 0-255 Description: Sets the Hset out gain level INACTIVITY TIMER Type: Register Format AT [cmds] S19=n [cmds] Default: 0 Range: 0-255 Description: Sets the system inactivity timer LINE OUT GAIN Type: Register Format: AT [cmds] S152=n [cmds] Range: 0-255 Description: Sets the line out gain level LINE QUALITY CONTROL Type: Register Format AT [cmds] S39? [cmds] Range: 0-2 Default: 2 Description: Displays the line quality control LINE RECORD GAIN Type: Register Format: AT [cmds] S139=n [cmds] Range: 0-255 Description: Sets the line record gain level LINE SELECTION DURATION Type: Register Format: AT [cmds] S78=n [cmds] Default: 0 Description: Sets the line selection duration MAX SPEED Type: Register Format: AT [cmds] S34=n [cmds] Description: Sets the requested MAX speed MICROPHONE Type: Register Format: AT [cmds] S90=n [cmds] Default: 1 Range: 0-3 Description: Sets the microphone MICROPHONE GAIN Type: Register Format: AT [cmds] S138=n [cmds] Range: 0-255 Description: Sets the microphone gain level MIN SPEED Type: Register Format: AT [cmds] S33=n [cmds] Description: Sets the requested MIN speed ORIGIN/ANSWER Type: Register Format AT [cmds] S22=n [cmds] Default: 0 Range: 0-1 Description: Sets the origin/answer PLAYBACK Type: Register Format: AT [cmds] S74=n [cmds] Default: 153 Range: 0-255 Description: Sets the playback volume PROCESSOR TYPE Type: Register Format: AT [cmds] S193=n [cmds] Default: 0 Range: 0-100 Description: Sets the processor type PULSE MAKE RATIO Type: Register Format: AT [cmds] S146=n [cmds] Default: 39 Range: 0-100 Description: Sets the pulse make ratio PULSE PAUSE Type: Register Format: AT [cmds] S148=n [cmds] Default: 80 Range: 0-255 Description: Sets the pulse pause PULSE PPS Type: Register Format: AT [cmds] S147=n [cmds] Default: 10 Range: 10, 20 Description: Sets the pulse PPS PULSE REFRESH Type: Register Format: AT [cmds] S149=n [cmds] Default: 0 Range: 0-100 Description: Sets the pulse refresh PULSE SET?BREAK RATIO Format AT [cmds] S28=n [cmds] Default: 0 Range: 0-4 Description: Sets the pulse set/break ratio PULSE TONE Type: Register Format: AT [cmds] S16=n [cmds] Default: 1 Range: 0-1 Description: Sets the pulse tone QUIET Type: Register Format AT [cmds] S14=n [cmds] Default: 0 Range: 0-1 Description: Sets the quiet function RECEIVED SIGNAL LEVEL Format AT [cmds] S41=n [cmds] Description: Displays the received signal level REQUESTED MODULATION Format: AT [cmds] S32=n [cmds] Default: 8 Range: Unidentified Description: Sets requested modulation RESULT CODES Type: Register Format: AT [cmds] S43=n [cmds] Description: Controls the result codes RING GOES AWAY TIMER Type: Register Format: AT [cmds] S79=n [cmds] Default: 70 Range: 0-255 Description: Sets the ring goes away timer RING NEVER CAME TIMER Type: Register Format: AT [cmds] S80=n [cmds] Default: 70 Range: 0-255 Description: Sets the ring never came timer RTS Type: Register Format: AT [cmds] S61=n [cmds] Default: 0 Range: 0-1 Description: Sets the RTS SIGNAL TO NOISE RATIO Type: Register Format: AT [cmds] S42=n [cmds] Description: Controls the signal to noise ratio setting. SILENCE DETECT Type: Register Format: AT [cmds] S81=n [cmds] Default: 0 Range: 0, 1 Description: Enables and disables the silence detection SILENCE DETECTION Type: Register Format: AT [cmds] S82=n [cmds] Default: 2 Range: 0-3 Unit: 0.1 second Description: Controls the silence detection sensitivity SILENCE DETECTION Type: Register Format: AT [cmds] S83=n [cmds] Default: 55 Range: 0-255 Description: Controls the silence detection duration SPEAKER Type: Register Format: AT [cmds] S89=n [cmds] Default: 5 Range: 0-15 Description: Sets the speaker SPEAKER CONTROL Type: Register Format AT [cmds] S29=n [cmds] Default: 1 Range: 0-3 Description: Sets the speaker control SPEAKER MUTE Type: Register Format: AT [cmds] S88=n [cmds] Default: 1 Range: 0-2 Description: Sets the speaker mute SPEAKER OUT GAIN Type: Register Format: AT [cmds] S153=n [cmds] Range: 0-255 Description: Sets the speaker out gain level SPEAKER VOLUME Type: Register Format AT [cmds] S30=n [cmds] Default: 2 Range: 0-3 Description: Sets the speaker volume TIME MARK Type: Register Format: AT [cmds] S87=n [cmds] Default: 0 Range: 0-255 Description: Controls the time mark placement TRANSMIT LEVEL GAIN Type: Register Format: AT [cmds] S45=n [cmds] Default: 3 Range: 0-10 Description: Controls the result codes VERBOSE Type: Register Format AT [cmds] S15=n [cmds] Default: 1 Range: 0-1 Description: Sets the verbose function VOICE SAMPLE Type: Register Format: AT [cmds] S91=n [cmds] Default: 0 Range: 1,2 Description: Sets the voice sample rate