OMNILINK COMMUNICATIONS CORPORATION NETPACER 241 Card Type ISDN TA Chipset Unidentified Error Correction/Compression Unidentified I/O Options ISDN line in, ISDN line out, 25-pin serial port, RJ-45 serial port, power, RJ-11 line out (4) ISDN Transfer Rate 64Kbps x 2 ISDN Protocol V.120, PPP, X.25 Switch Type 5ESS, DMS-100, Siemens Data Bus External [Image] CONNECTIONS Function Label Function Label RJ-45 ISDN interface CN1 RJ-11 analog phone CN6 interface - line 1 S/T interface CN2 RJ-11 analog phone CN7 interface - line 2 Serial port 1 (25-pin CN3 RJ-11 analog phone CN8 connector) interface - line 3 Serial port 2 (RJ-45 CN4 RJ-11 analog phone CN9 interface) interface - line 4 Power connector CN5 Note: RJ-11 lines 1 & 2 share B-channel 1. RJ-11 lines 3 & 4 are assigned to B-channel 2. SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’ A, E, F, V Note: See MHI Help File for full command documentation. PROPRIETARY AT COMMAND SET HOOK CONTROL Type: Immediate Format: AT [cmds] H Description: Modem hangs up ON-LINE Type: Immediate Format: AT [cmds] O Description: Reestablishes data transfer mode REPORT INFORMATION Type: Immediate Format: AT [cmds] I Description: Displays firmware version and data X.23 COMMANDS Type: Immediate Format: [cmds] Description: Configures serial port for X.28 DIAGNOSTIC LED(S) LED Color Status Condition T1 Unidentified On Data is being transmitted to serial port 1 T1 Unidentified Off Data is not being transmitted to serial port 1 T2 Unidentified On Data is being transmitted to serial port 2 T2 Unidentified Off Data is not being transmitted to serial port 2 R1 Unidentified On Data is being received from serial port 1 R1 Unidentified Off Data is not being received from serial port 1 R2 Unidentified On Data is being received from serial port 2 R2 Unidentified Off Data is not being received from serial port 2 L1 Unidentified On Analog phone equipment is connected to line 1; off-hook L1 Unidentified Off Analog phone equipment is not connected to line 1; on-hook L2 Unidentified On Analog phone equipment is connected to line 2; off-hook L2 Unidentified Off Analog phone equipment is not connected to line 2; on-hook L3 Unidentified On Analog phone equipment is connected to line 3; off-hook L3 Unidentified Off Analog phone equipment is not connected to line 3; on-hook L4 Unidentified On Analog phone equipment is connected to line 4; off-hook L4 Unidentified Off Analog phone equipment is not connected to line 4; on-hook B1 Unidentified On Bearer channel 1 is in use B1 Unidentified Off Bearer channel 1 is not in use B2 Unidentified On Bearer channel 2 is in use B2 Unidentified Off Bearer channel 2 is not in use DCH Unidentified On Data channel is in use DCH Unidentified Off Data channel is not in use CON Unidentified On Custom application is installed CON Unidentified Off Custom application is not installed UL Unidentified On ISDN connection with the switch is normal UL Unidentified Off ISDN not connected with the switch. UL Unidentified Blinking ISDN connection with the switch has been made, but the TEI is being negotiated ER Unidentified On Errors have been detected on network ER Unidentified Off Errors have not been detected on network CA Unidentified On Custom application is being run CA Unidentified Off Custom application is not being run PWR Unidentified On Power is on PWR Unidentified Off Power is off