APACHE MICRO PERIPHERALS, INC. APACHE A56-R Card Type Modem (asynchronous) Chip Set Unidentified I/O Options Speaker out, microphone Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.21, V.22bis, V.23, V.32, V.32bis, V.34, V.34+, V.FC, K56flex, V.90 Fax Modulation Protocol ITU-T V.17, V.21 CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I Data Bus 16-bit ISA Card Size Half-length, full-height card [Image] CONNECTIONS Function Label Function Label Line out CN1 Line in CN2 SERIAL PORT ADDRESS Setting SW1/5 SW1/6 COM1 (3F8h) On On COM2 (2F8h) Off On COM3 (3E8h) On Off COM4 (2E8h) Off Off INTERRUPT Setting SW1/1 SW1/2 SW1/3 SW1/4 SW1/7 JP1 IRQ 2 Off Off Off Off On Open IRQ 3 Off Off Off On Off Open IRQ 4 Off Off On Off Off Open IRQ 5 Off On Off Off Off Open IRQ 7 On Off Off Off Off Open IRQ 10 Off Off Off Off Off 2 & 3 IRQ 11 Off Off Off Off Off 1 & 2 Note: Pins designated are in the closed position SUPPORTED COMMAND SET Basic AT Commands AT, A/ A, B, D, E, H, M, O, P, Q, T, V, W, X, Y, Z &C, &D, &M, &P, &Q, &R, &T, &W, &X, &Y, &Z Extended AT Commands \A, \B, \K, \N %C, %E, %L, %Q S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95 Special Commands -K, +MS Note: See MHI Help File for full command documentation. Proprietary AT Command Set TRANSMIT CARRIER Type: Configuration Format: AT [cmds] Cn [cmds] Description: Controls the transmit carrier switching Note: Disabling the transmit carrier puts the modem in receive-only mode Command Function C1 Return OK message LINE MODULATION Type: Configuration Format: AT [cmds] Fn [cmds] Description: Selects the line modulation Note: This command is only supported on older modems Command Function F0 Auto-detect mode F1 V.21 or Bell 103 F3 V.23 F4 V.22 or Bell 212A @ 1200bps F5 V.22bis F6 V.32bis or V.32 @ 4800bps F7 V.32bis @ 7200bps F8 V.32bis or V.32 @ 9600bps F9 V.32bis @ 12000bps F10 V.32bis @ 14400bps REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product code I1 Reports ROM checksum I2 Reports OK I3 Report firmware revision, model interface type I4 Reports response programmed by an OEM I5 Reports country code I6 Reports modem data pump model and code revision I7 Reports DAA code (W-class only) SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Auto-mode detection disabled N1 Auto-mode detection enabled FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &F [cmds] Description: Sets values in active profile to values found in the default profile Command Function &F0 Restore factory profile 0 &F1 Restore factory profile 1 GUARD TONE Type: Configuration Format: AT [cmds] &Gn [cmds] Description: Commands the modem to transmit a guard tone in V.22/V.22bis Note: Used primarily for international data transmission Command Function &G0 Guard tone disabled &G1 Guard tone disabled &G2 1800Hz guard tone enabled S-REGISTER RESPONSE Type: Configuration Format: AT [cmds] &Jn [cmds] Description: This command included for compatibility. It performs no function. FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 RTS/CTS flow control enabled &K4 XON/XOFF flow control enabled &K5 Transparent XON/XOFF flow control enabled &K6 RTS/CTS and XON/XOFF flow control enabled LINE TYPE Type: Configuration Format: AT [cmds] &Ln [cmds] Description: Selects line type Command Line Type &L0 Switched line (PSTN/Dial-up) DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high while modem is handshaking or connected CONFIGURATION PROFILES Type: Immediate Format: AT [cmds] &V [cmds] Description: Displays active and stored configuration profiles Command Function &V1 Display connection statistics Extended AT Commands EXTENDED RESULT CODES Type: Configuration Format: AT [cmds] \Vn [cmds] Description: Selects extended result codes Command Function \V0 Connect messages are controlled by settings X, W, and S95 \V1 Connect messages are displayed in the single line format PLUG AND PLAY SERIAL NUMBER Type: Immediate Format: AT [cmds] %7 [cmds] Description: Returns the plug & play serial number PLUG AND PLAY VENDOR ID Type: Immediate Format: AT [cmds] %8 [cmds] Description: Returns the plug & play vendor ID and product number RPI MODE SELECTION Type: Configuration Format: AT [cmds] +Hn [cmds] Description: Sets the RPI mode Command Function +H0 RPI/video ready mode disabled +H1 RPI enabled and set DTE speed to 19200bps +H2 RPI enabled and set DTE speed to 38400bps +H3 RPI enabled and set DTE speed to 57600bps +H11 RPI+ mode enabled +H16 Video ready mode enabled DISTINCTIVE RING Type: Immediate Format: AT [cmds] -SDR=n [cmds] Description: Selects the distinctive ring settings Command Function -SDR=0 Distinctive ring disabled -SDR=1 Type 1 enabled -SDR=2 Type 2 enabled -SDR=3 Type 1 and 2 enabled -SDR=4 Type 3 enabled -SDR=5 Type 1 and 3 enabled -SDR=6 Type 2 and 3 enabled -SDR=7 Type 1, 2, and 3 enabled MNP10-EC Type: Configuration Format: AT [cmds] -SECn [cmds] Description: Controls MNP10-EC Command Function -SEC0 MNP10-EC disabled -SEC1 MNP10-EC enabled ans set transmit (TX) level to 0 - 30 S(status) -REGISTERS AUTOSYNC OPTIONS Type: Register Format AT [cmds] S19=n [cmds] Default: 0 Range: Unidentified Description: Sets the AutoSync option AUTOSYNC HDLC ADDRESS Type: Register Format AT [cmds] S20=n [cmds] Default: 0 Range: 0-255 Description: Sets the AutoSync HDLC address of BSC Sync charactyer